Fracture process of a low carbon low alloy steel relevant to charpy toughness at ductile-brittle fracture transition region

1995 ◽  
Vol 26 (2) ◽  
pp. 391-399 ◽  
Author(s):  
T. Tani ◽  
M. Nagumo
Keyword(s):  
Brittle Fracture ◽  
Transition Region ◽  
Alloy Steel ◽  
Fracture Process ◽  
Low Carbon ◽  
Low Alloy Steel ◽  
Fracture Transition

Effect of thermomechanical treatment on the resistance of low-carbon low-alloy steel to brittle fracture

2015 ◽  
Vol 116 (2) ◽  
pp. 189-199 ◽  
Author(s):  
V. M. Schastlivtsev ◽  
T. I. Tabatchikova ◽  
I. L. Yakovleva ◽  
S. Yu. Del’gado Reina ◽  
S. A. Golosienko ◽  
...  
Keyword(s):  
Brittle Fracture ◽  
Alloy Steel ◽  
Thermomechanical Treatment ◽  
Low Carbon ◽  
Low Alloy Steel

Research of Recrystallization Processes in Low-Carbon Low-Alloy Steel in Modeling High-Temperature Rolling

2019 ◽  
Vol 10 (6) ◽  
pp. 1301-1308 ◽  
Author(s):  
S. V. Korotovskaya ◽  
O. V. Sych ◽  
E. I. Khlusova ◽  
E. A. Yashina
Keyword(s):  
High Temperature ◽  
Alloy Steel ◽  
Low Carbon ◽  
Low Alloy Steel

scholarly journals Applied Aspects of Low-carbon and Low-alloy Steel Recrystallization

2015 ◽  
Vol 11 (10) ◽  
pp. 1075-1083
Author(s):  
Elena Smirnova ◽  
Valery Gordienko ◽  
Evgeny Gordienko
Keyword(s):  
Alloy Steel ◽  
Low Carbon ◽  
Low Alloy Steel

Study of Low Carbon Low Alloy Steel Annealing Process Parameters Optimization

2013 ◽  
Vol 631-632 ◽  
pp. 649-659
Author(s):  
Mao Yu Zhao ◽  
Qian Wang Chen
Keyword(s):  
Yield Strength ◽  
Alloy Steel ◽  
Process Parameters ◽  
Orthogonal Experiment ◽  
Annealing Process ◽  
Parameters Optimization ◽  
Grey Theory ◽  
Low Carbon ◽  
Low Alloy Steel ◽  
Sem Images

A suitable match of annealing process parameters is critical for obtaining the fine microstructure of material. Low carbon low alloy steel (20CrMnTi) was heated for various durations near Ac temperature to achieve fine pearlite and ferrite grains. Annealing temperature and time were used as independent variables, and material property data were acquired by orthogonal experiment under intercritical annealing followed by subcritical annealing process (IASAP). The weights of plasticity (hardness, yield strength, section shrinkage, and elongation) of annealing material were calculated by analytic hierarchy process, and then the process parameters were optimized by using the grey theory system. The results observed by SEM images show that the optimized material microstructure consists of refining and distributing uniformly ferrite-pearlite grains, and smaller lamellar cementites. Morphologies on tension fracture surface of the optimized material indicates that the numbers of dimple fracture show more finer toughness obviously comparing with other annealing materials. Moreover, the yield strength value of the optimized material decreases apparently measured by tensile test. Thus, the new optimized strategy is accurate and feasible.

scholarly journals Relation between Inclusion Surface and Acicular Ferrite in Low Carbon Low Alloy Steel Weld

2009 ◽  
Vol 49 (7) ◽  
pp. 1059-1062 ◽  
Author(s):  
Tomonori Yamada ◽  
Hidenori Terasaki ◽  
Yu-ichi Komizo
Keyword(s):  
Alloy Steel ◽  
Acicular Ferrite ◽  
Steel Weld ◽  
Low Carbon ◽  
Low Alloy Steel
Sign in / Sign up

Export Citation Format

Share Document