High temperature plastic deformation of two V-Ga alloys with A15 structure

1986 ◽  
Vol 17 (3) ◽  
pp. 519-525 ◽  
Author(s):  
Gregory B. Soscia ◽  
Roger N. Wright
Keyword(s):  
Plastic Deformation ◽  
High Temperature

scholarly journals Structural Transformations and Mechanical Properties of Metastable Austenitic Steel under High Temperature Thermomechanical Treatment

Metals ◽  
2021 ◽  
Vol 11 (4) ◽  
pp. 645
Author(s):  
Igor Litovchenko ◽  
Sergey Akkuzin ◽  
Nadezhda Polekhina ◽  
Kseniya Almaeva ◽  
Evgeny Moskvichev
Keyword(s):  
Plastic Deformation ◽  
Grain Size ◽  
High Temperature ◽  
Austenitic Steel ◽  
Structural Transformations ◽  
Initial State ◽  
Twin Boundaries ◽  
Metastable Austenitic Steel ◽  
Average Grain Size ◽  
Heating Up

The effect of high-temperature thermomechanical treatment on the structural transformations and mechanical properties of metastable austenitic steel of the AISI 321 type is investigated. The features of the grain and defect microstructure of steel were studied by scanning electron microscopy with electron back-scatter diffraction (SEM EBSD) and transmission electron microscopy (TEM). It is shown that in the initial state after solution treatment the average grain size is 18 μm. A high (≈50%) fraction of twin boundaries (annealing twins) was found. In the course of hot (with heating up to 1100 °C) plastic deformation by rolling to moderate strain (e = 1.6, where e is true strain) the grain structure undergoes fragmentation, which gives rise to grain refining (the average grain size is 8 μm). Partial recovery and recrystallization also occur. The fraction of low-angle misorientation boundaries increases up to ≈46%, and that of twin boundaries decreases to ≈25%, compared to the initial state. The yield strength after this treatment reaches up to 477 MPa with elongation-to-failure of 26%. The combination of plastic deformation with heating up to 1100 °C (e = 0.8) and subsequent deformation with heating up to 600 °C (e = 0.7) reduces the average grain size to 1.4 μm and forms submicrocrystalline fragments. The fraction of low-angle misorientation boundaries is ≈60%, and that of twin boundaries is ≈3%. The structural states formed after this treatment provide an increase in the strength properties of steel (yield strength reaches up to 677 MPa) with ductility values of 12%. The mechanisms of plastic deformation and strengthening of metastable austenitic steel under the above high-temperature thermomechanical treatments are discussed.

High temperature plastic deformation of multilayered YTZP/ZTA composites obtained by tape casting

1998 ◽  
Vol 46 (11) ◽  
pp. 3995-4004 ◽  
Author(s):  
M. Jiménez-Melendo ◽  
C. Clauss ◽  
A. Domi ́nguez-Rodri ́guez ◽  
G. de Portu ◽  
E. Roncari ◽  
...  
Keyword(s):  
Plastic Deformation ◽  
High Temperature ◽  
Tape Casting

Intermetallics of Aluminum

2019 ◽  
Author(s):  
Georg Frommeyer ◽  
Sven Knippscheer
Keyword(s):  
Crystal Structure ◽  
Mechanical Properties ◽  
Plastic Deformation ◽  
High Temperature ◽  
Physical Properties ◽  
Intermetallic Compounds ◽  
Oxidation Behavior ◽  
Physical And Mechanical Properties ◽  
Structural Materials

Aluminum-rich intermetallic compounds of the Al3X-type with transmission metals (X = Ti. Zr, Nb, V) of Groups IVb and Vb are of interest in the development of novel high-temperature and lightweight structural materials. This article describes the important physical and mechanical properties of trialuminides with DO22 structure and their L12 variations. Topical coverage includes: crystal structure and selected physical properties, plastic deformation, oxidation behavior, and applications.

Plastic Deformation of Approximants: Dislocations vs. Phason Lines

1998 ◽  
Vol 553 ◽  
Author(s):  
H. Klein ◽  
M. Feuerbacher ◽  
P. Schall ◽  
K. Urban
Keyword(s):  
Plastic Deformation ◽  
High Temperature ◽  
Single Crystals ◽  
Periodic Lattice ◽  
Length Scale ◽  
Relative Importance ◽  
Line Lattice ◽  
Burgers Vector ◽  
Mechanisms Of Plastic Deformation

AbstractDeformation experiments were performed on single crystals of the ξ-AIPdMn approximant in bending geometry at high temperature. Two different mechanisms of plastic deformation are shown to exist in this phase: one based on dislocations and another novel mechanism based on the motion of phason lines. Burgers vector and line directions of dislocations were determined. Phason lines are shown to build a periodic lattice. The interaction of a dislocation with the phason line lattice results in dislocations on another length scale. This meta-dislocation in the periodic phason line lattice has a Burgers vector of magnitude 165 Å. The relative importance of phason lines and dislocations for the plastic deformation is discussed as a function of the orientation of the sample with respect to the bending geometry.

Sign in / Sign up

Export Citation Format

Share Document