Flame propagation of burning solid material with moisture

1971 ◽  
Vol 7 (3) ◽  
pp. 243-250 ◽  
Author(s):  
Shuh-Jing Ying
Keyword(s):  
Flame Propagation ◽  
Solid Material

Effect of an electric field on the flame propagation over a solid material surface

1992 ◽  
Vol 28 (3) ◽  
pp. 244-246 ◽  
Author(s):  
A. F. Panteleev ◽  
G. A. Popkov ◽  
S. G. Tsarichenko ◽  
Yu. N. Shebeko
Keyword(s):  
Electric Field ◽  
Flame Propagation ◽  
Solid Material ◽  
Material Surface

Effects of Ion Beam Milling on Surface Topography

1973 ◽  
Vol 31 ◽  
pp. 84-85
Author(s):  
P.G. Pawar ◽  
P. Duhamel ◽  
G.W. Monk
Keyword(s):  
Surface Topography ◽  
Ion Beam ◽  
Solid Material ◽  
Beam Current ◽  
Atomic Mass ◽  
Micro Milling ◽  
Ion Milling ◽  
Controlled Atmospheres ◽  
Milling Operations ◽  
Sufficient Energy

A beam of ions of mass greater than a few atomic mass units and with sufficient energy can remove atoms from the surface of a solid material at a useful rate. A system used to achieve this purpose under controlled atmospheres is called an ion miliing machine. An ion milling apparatus presently available as IMMI-III with a IMMIAC was used in this investigation. Unless otherwise stated, all the micro milling operations were done with Ar+ at 6kv using a beam current of 100 μA for each of the two guns, with a specimen tilt of 15° from the horizontal plane.It is fairly well established that ion bombardment of the surface of homogeneous materials can produce surface topography which resembles geological erosional features.

Contrast and Resolution in Alfresco Microscopy and Thick Specimens

1972 ◽  
Vol 30 ◽  
pp. 570-571
Author(s):  
J. R. Sellar ◽  
J. M. Cowley
Keyword(s):  
Solid Material ◽  
Cell Design ◽  
Current Interest ◽  
High Voltage Electron Microscopy ◽  
Voltage Electron ◽  
Transmission Electron ◽  
Environmental Cell ◽  
Scanning Transmission ◽  
Conventional Transmission Electron Microscope ◽  
Transmission Microscope

Current interest in high voltage electron microscopy, especially in the scanning mode, has prompted the development of a method for determining the contrast and resolution of images of specimens in controlled-atmosphere stages or open to the air, hydrated biological specimens being a good example. Such a method would be of use in the prediction of microscope performance and in the subsequent optimization of environmental cell design for given circumstances of accelerating voltage, cell gas pressure and constitution, and desired resolution.Fig. 1 depicts the alfresco cell of a focussed scanning transmission microscope with a layer of gas L (and possibly a thin window W) between the objective O and specimen T. Using the principle of reciprocity, it may be considered optically equivalent to a conventional transmission electron microscope, if the beams were reversed. The layer of gas or solid material after the specimen in the STEM or before the specimen in TEM has no great effect on resolution or contrast and so is ignored here.

Numerical study of pressure and composition influence on laminar flame propagation in nitrogen-diluted H2-O2 mixtures

2020 ◽  
Vol 65 (6) ◽  
pp. 529-537
Author(s):  
Domnina RAZUS ◽  
◽  
Maria MITU ◽  
Venera GIURCAN ◽  
Codina MOVILEANU ◽  
...  
Keyword(s):  
Flame Propagation ◽  
Laminar Flame ◽  
Numerical Study

Atomic disruption beam theory

2016 ◽  
pp. 3524-3528
Author(s):  
Casey Ray McMahon
Keyword(s):  
Neutron Beam ◽  
Beam Theory ◽  
Solid Material ◽  
Material Matter ◽  
Solid Matter ◽  
Plasma Generation ◽  
Resulting Effect ◽  
Drilling Operations ◽  
The Stability

In this paper, I discuss the theory behind the use of a dense, concentrated neutron particle-based beam. I look at the particle based physics behind such a beam, when it is focused against solid material matter. Although this idea is still only theoretical, it appears that such a beam may be capable of disrupting the stability of the atoms within solid matter- in some cases by passing great volumes of neutrons between the electron and nucleus thus effectively “shielding” the electron from the charge of the nucleus. In other cases, by disrupting the nucleus by firing neutrons into it, disrupting the nucleus and weakening its bond on electrons. In either case- the resulting effect would be a disruption of the atom, which in the case of material matter would cause said material matter to fail, which would appear to the observer as liquification with some plasma generation. Thus, a dense neutron particle based beam could be used to effectively liquefy material matter. Such a beam could bore through rock, metal, or even thick, military grade armour, like that used on tanks- causing such materials to rapidly liquefy. The denser and thicker the neutron beam, the more devastating the effect of the beam- thus the faster material matter will liquefy and the greater the area of liquification. Such a beam would have applications in Defence, mining and drilling operations.

Sign in / Sign up

Export Citation Format

Share Document