Influence of dynamic loads due to a cutter-loader on the strength of consolidated stowage material

1978 ◽  
Vol 14 (3) ◽  
pp. 322-324
Author(s):  
M. I. Veskov ◽  
M. P. Mokhnachev ◽  
N. V. Gromova ◽  
N. N. Vanifatov
Keyword(s):  
Dynamic Loads ◽  
Stowage Material

Study of the dynamics of ТПА 350 automatic mill working stand elements

2020 ◽  
Vol 76 (8) ◽  
pp. 830-840
Author(s):  
S. R. Rakhmanov ◽  
V. V. Povorotnii
Keyword(s):  
Mechanical System ◽  
Dynamic Model ◽  
Maximum Amplitude ◽  
Calculation Scheme ◽  
Dynamic Loads ◽  
Forced Oscillations ◽  
Mass Model ◽  
Automatic Mill ◽  
Hollow Billet ◽  
Oscillation Movement

To form a necessary geometry of a hollow billet to be rolled at a pipe rolling line, stable dynamics of the base equipment of the automatic mill working stand has a practical meaning. Among the forces, acting on its parts and elements, significant by value short-time dynamic loads are the least studied phenomena. These dynamic loads arise during transient interaction of the hollow billet, rollers, mandrel and other mill parts at the forced grip of the hollow billet. Basing of the calculation scheme and dynamic model of the mechanical system of the ТПА 350 automatic mill working stand was accomplished. A mathematical model of dynamics of the system “hollow billet (pipe) – working stand” within accepted calculation scheme and dynamic model of the mechanical system elaborated. Influence of technological load of the rolled hollow billet variation in time was accounted, as well as variation of the mechanical system mass, and rigidity of the ТПА 350 automatic mill working stand. Differential equations of oscillation movement for four-mass model of forked sub-systems of the automatic mill working stand were made up, results of their digital calculation quoted. Dynamic displacement of the stand elements in the inter-roller gap obtained, which enabled to estimate the results of amplitude and frequency characteristics of the branches of the mill rollers setting. It was defined by calculation, that the maximum amplitude of the forced oscillations of elements of the ТПА 350 automatic mill working stand within the inter-roller gap does not exceed 2 mm. It is much higher than the accepted value of adjusting parameters of the deformation center of the ТПА 350 automatic mill. A scheme of comprehensive modernization of the rollers setting in the ТПА 350 automatic mill working stand was proposed. It was shown, that increase of rigidity of rollers setting in the ТПА 350 automatic mill working stand enables to stabilize the amplitude of forced oscillations of the working stand elements within the inter-rollers gap and considerably decrease the induced nonuniform hollow billet wall thickness and increase quality of the rolled pipes at ТПА 350.

Reducing dynamic loads in the mechatronic system of a rolling mill

2020 ◽  
pp. 45-48
Author(s):  
S.I. Malafeev ◽  
A.A. Malafeeva ◽  
V.I. Konyashin
Keyword(s):  
Direct Current ◽  
Electric Drive ◽  
Rolling Mill ◽  
Correction Method ◽  
System Model ◽  
Dynamic Loads ◽  
Dynamic Processes ◽  
Mechatronic System

A correction method for regulating the mechatronic system of a «DUO-300» rolling mill with a direct current electric drive is considered. The results of the study of dynamic processes in the mechatronic system with the proposed correction are presented. Keywords rolling mill, mechatronic system, model, electric drive, engine, regulator, correction. [email protected]

Modeling of Dynamic Loads on the Polished Rod of Pumping Unit in Case of Mulfunction of Rod Pump Operating

2014 ◽  
Vol 10 ◽  
pp. 95-101
Author(s):  
A.S. Topolnikov
Keyword(s):  
Multiphase Flow ◽  
Satisfactory Agreement ◽  
Model Simulation ◽  
Theoretical Modeling ◽  
Dynamic Loads ◽  
Plunger Pump ◽  
Proposed Model ◽  
Pumping Unit ◽  
Polished Rod

The paper presents the results of theoretical modeling of joined movement of pump rods and plunger pump and multiphase flow in a well for determination of dynamic loads on the polished rod of pumping unit. The specificity of the proposed model is the possibility of taking into account for complications in rod pump operating, such as leakage in valve steam, presence of gas and emulsion, incorrect fitting of plunger inside the cylinder pump. The satisfactory agreement of results of the model simulation with filed measurements are obtained.

Sign in / Sign up

Export Citation Format

Share Document