Fracture mechanical properties of high-performance concrete—Influence of silica fume

2000 ◽  
Vol 33 (9) ◽  
pp. 552-558 ◽  
Author(s):  
K. O. Kjellsen ◽  
M. Hallgren ◽  
O. H. Wallevik
Keyword(s):  
Mechanical Properties ◽  
Silica Fume ◽  
High Performance ◽  
High Performance Concrete

scholarly journals Effect of different curing conditions on the mechanical properties of reactive powder concrete

2018 ◽  
Vol 162 ◽  
pp. 02014
Author(s):  
Mazin Abdulrahman ◽  
Alyaa Al-Attar ◽  
Marwa Ahmad
Keyword(s):  
Mechanical Properties ◽  
Silica Fume ◽  
High Performance ◽  
High Performance Concrete ◽  
Material Constant ◽  
Hot Water ◽  
Modulus Of Rupture ◽  
Reactive Powder Concrete ◽  
Curing Conditions ◽  
Reactive Powder

Reactive Powder Concrete (RPC) is an ultra-high performance concrete which has superior mechanical and physical properties, and composed of cement and very fine powders such as quartz sand and silica fume with very low water/ binder ratio and Superplasticizer. Heat treatment is a well-known method that can further improve the performance of (RPC). The current research including an experimental study of the effect of different curing conditions on mechanical properties of reactive powder concrete (compressive strength, modulus of rupture and splitting tensile strength), the curing conditions includes three type of curing; immersion in water at temperature of 35 OC (which is considered as the reference-curing situation), immersion in water at temperature of 90 OC for 5 hours daily and curing with hot steam for 5 hours daily) until 28 days according to ASTM C684-99 [8]. This research includes also the study of effect of adding silica fume as percentage of cement weight on mechanical properties of reactive powder concrete for different percentage ratios (5%,10% and 15%). Super plasticizer is also used with ratio of (1.8%) by weight of cementitious material; constant water cement ratio (0.24) was used for all mixes. For each reactive concrete mix, it has been cast into a cubes of (150*150*150) (to conduct the compression test), a cylinders of 150mm diameter with 300mm height (to conduct split test) and prisms of (500*100*100)mm to conduct the modulus of rupture test. The results showed that the best method of curing (according to its enhancing the RPC mechanical properties) is the method of immersion in hot water at temperature 90 OC for the all silica fume percentages, and the best used silica fume percentage was (10%) for the all used curing methods.

Effect of the Type of Silica Fume and Filler on Mechanical Properties of Ultra High Performance Concrete

2018 ◽  
Vol 774 ◽  
pp. 349-354 ◽  
Author(s):  
Kyung Taek Koh ◽  
Seung Hun Park ◽  
Gum Sung Ryu ◽  
Gi Hong An ◽  
Byung Suk Kim
Keyword(s):  
Mechanical Properties ◽  
Silica Fume ◽  
High Performance ◽  
High Performance Concrete ◽  
Strength Loss ◽  
Limestone Powder ◽  
Cement Kiln ◽  
Ultra High Performance Concrete ◽  
Silica Powder ◽  
Kiln Dust

The large quantities of expensive materials such as steel fiber, silica fume, filler and superplasticizer required in the composition of Ultra-High Performance Concrete (UHPC) make its fabrication cost significantly higher than ordinary concrete. This study evaluates the effect of the type of silica fume and filler on mechanical properties of UHPC. The evaluation shows that the use of Zr silica powder instead of common silica fume improves significantly the fluidity of UHPC without loss of the strength and enables to reduce the amount of superplasticizer by maximum 70%. Moreover, the evaluation of the effect of the type and size of the filler reveals that modifying the size of the filler from 2 μm to 4 μm enhances the fluidity without strength loss and that the use of cement kiln dust (CKD) and limestone powder can achieve UHPC with compressive strength higher than 150 MPa. These results show that the use of the materials such as Zr silica powder, CKD and limestone powder can help to fabricate more economic UHPC.

An Experimental Study on Evaluation of Mechanical Properties in High Performance Concrete Using Admixture

2013 ◽  
Vol 372 ◽  
pp. 231-234
Author(s):  
Jeong Eun Kim ◽  
Wan Shin Park ◽  
Nam Yong Eom ◽  
Sun Woong Kim ◽  
Do Gyeum Kim ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Compressive Strength ◽  
Silica Fume ◽  
Modulus Of Elasticity ◽  
High Performance ◽  
High Performance Concrete ◽  
Splitting Tensile Strength ◽  
Experimental Investigations ◽  
Binder Ratio

In this study, some experimental investigations on the development of mechanical properties with age of high performance concrete (HPC) incorporated with blast furnace slag with fly ash or silica fume have been reported. Four different blended HPC were prepared in 0.40 water-binder ratio. At every four mixtures, the compressive strength, splitting tensile strength and modulus of elasticity at 7 and 28 days have been observed for HPC developments. Consequently, only replacement of silica fume significantly increases the mechanical properties in terms of compressive strength, splitting tensile strength and modulus of elasticity.

scholarly journals Physico-mechanical properties of high performance concrete using different aggregates in presence of silica fume

HBRC Journal ◽  
2014 ◽  
Vol 10 (1) ◽  
pp. 43-48 ◽  
Author(s):  
Salah A. Abo-El-Enein ◽  
Hamdy A. El-Sayed ◽  
Ali H. Ali ◽  
Yasser T. Mohammed ◽  
Hisham M. Khater ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Silica Fume ◽  
High Performance ◽  
High Performance Concrete
Sign in / Sign up

Export Citation Format

Share Document