The analyses of the three-dimensional stress structure near the crack tip of mode I CT specimens in elastic-plastic state (I)—The analyses of constraint parameters and fracture parameters

1993 ◽  
Vol 14 (7) ◽  
pp. 659-668 ◽  
Author(s):  
Yue Zhu-feng ◽  
Zheng Chang-qing
Keyword(s):  
Three Dimensional ◽  
Crack Tip ◽  
Plastic State ◽  
Mode I ◽  
Elastic Plastic ◽  
Fracture Parameters

On the Extent of Dominance of Asymptotic Elastodynamic Crack-Tip Fields: Part II—Numerical Investigation of Three-Dimensional and Transient Effects

1991 ◽  
Vol 58 (1) ◽  
pp. 95-103 ◽  
Author(s):  
Sridhav Krishnaswamy ◽  
Ares J. Rosakis ◽  
G. Ravichandran
Keyword(s):  
Three Dimensional ◽  
Crack Tip ◽  
Experimental Results ◽  
Mode I ◽  
Transient Effects ◽  
Adequate Description ◽  
Crack Tip Field ◽  
Drop Weight ◽  
The Impact ◽  
Laboratory Specimen

In Part I of this paper, the question of the extent of dominance of the mode I asymptotic elastodynamic crack-tip field (the KdI-field) was studied experimentally. Here, the results of two and three-dimensional elastodynamic finite element simulations of the drop-weight experiments are reported. The load records as obtained from the impact hammer and supports of the drop-weight loading device were used as boundary tractions in the numerical simulations. For the laboratory specimen studied, the results of the simulations indicate that the asymptotic elastodynamic field is not an adequate description of the actual fields prevailing over any sizeable region around the crack tip. This confirms the experimental results of Part I which showed that three-dimensional and transient effects necessarily have to be taken into account for valid interpretation of experimental results.

Elastic-plastic J-Tz dominance in bending and tension loadings

2019 ◽  
Vol 10 (5) ◽  
pp. 644-659
Author(s):  
Feizal Yusof ◽  
Karh Heng Leong
Keyword(s):  
Crack Length ◽  
Power Law ◽  
Crack Front ◽  
Three Dimensional ◽  
Crack Tip ◽  
Content Type ◽  
Elastic Plastic ◽  
Crack Tip Fields ◽  
Out Of Plane ◽  
Crack Tip Stress

Purpose Crack tip stresses are used to relate the ability of structures to perform under the influence of cracks and defects. One of the methods to determine three-dimensional crack tip stresses is through the J-Tz method. The J-Tz method has been used extensively to characterize the stresses of cracked geometries that demonstrate positive T-stress but limited in characterizing negative T-stresses. The purpose of this paper is to apply the J-Tz method to characterize a three-dimensional crack tip stress field in a changing crack length from positive to negative T-stress geometries. Design/methodology/approach Elastic-plastic crack border fields of deep and shallow cracks in tension and bending loads were investigated through a series of three-dimensional finite element (FE) and analytical J-Tz solutions for a range of crack lengths ranging from 0.1⩽a/W⩽0.5 for two thickness extremes of B/(W − a)=1 and 0.05. Findings Both the FE and the J-Tz approaches showed that the combined in-plane and the out-of-plane constraint loss were differently affected by the T-stress and the out-of-plane size effects when the crack length changed from deep to shallow cracks. The conditions of the J-Tz dominance on the three-dimensional crack front tip were shown to be limited to positive T-stress geometries, and the J-Tz-Q2D approach can extend the crack border dominance of the three-dimensional deep and shallow bend models along the crack front tip until perturbed by an elastic-plastic corner field. Practical implications The paper reports the limitation of the J-Tz approach, which is used to calculate the state of three-dimensional crack tip stresses in power law hardening materials. The results from this paper suggest that the characterization of the three-dimensional crack tip stress in power law hardening materials is still an open issue and requires other suitable solutions to solve the problem. Originality/value This paper demonstrates a thorough analysis of a three-dimensional elastic-plastic crack tip fields for geometries that are initially either fully constrained (positive T-stress) or unconstrained (negative T-stress) crack tip fields but, subsequently, the T-stress sign changes due to crack length reduction and specimen thickness increase. The J-Tz stress-based method has been tested and its dominance over the crack tip field is shown to be affected by the combined in-plane and the out-of-plane constraints and the corner field effects.

On the Extent of Dominance of Asymptotic Elastodynamic Crack-Tip Fields: Part I—An Experimental Study Using Bifocal Caustics

1991 ◽  
Vol 58 (1) ◽  
pp. 87-94 ◽  
Author(s):  
Sridhar Krishnaswamy ◽  
Ares J. Rosakis
Keyword(s):  
High Speed ◽  
Dynamic Stress ◽  
Dynamic Stress Intensity Factor ◽  
Three Dimensional ◽  
Crack Tip ◽  
Mode I ◽  
Transient Effects ◽  
Crack Tip Fields ◽  
Optical Configuration ◽  
Point Bend

The question of the domain of dominance of mode I asymptotic elastodynamic crack-tip fields is investigated experimentally for the cases of dynamically loaded stationary cracks as well as dynamically propagating cracks. The experiments reported are on three-point bend specimens loaded dynamically using a drop-weight tower. An optical configuration leading to a bifocal high-speed camera is proposed. This is used in conjunction with the method of caustics to obtain apparent dynamic stress intensity factor measurements simultaneously from two different regions around the crack tip. The results of this study indicate that three-dimensional and transient effects necessarily have to be taken into account in the interpretation of dynamic fracture experiments.

Sign in / Sign up

Export Citation Format

Share Document