Discussions on “An asymptotic elastic plastic analysis in plane strain deformation near a crack tip”

1981 ◽  
Vol 2 (6) ◽  
pp. 779-781
Author(s):  
Meng Xian-gang
Keyword(s):  
Plane Strain ◽  
Crack Tip ◽  
Elastic Plastic ◽  
Plane Strain Deformation ◽  
Plastic Analysis

scholarly journals A Numerical Analysis of Selected Elastic-Plastic Fracture Parameters for DEN(T) Plates under Plane Strain Conditions

2017 ◽  
Vol 22 (1) ◽  
pp. 49-80 ◽  
Author(s):  
M. Graba
Keyword(s):  
Numerical Analysis ◽  
Fracture Mechanics ◽  
Plane Strain ◽  
Plastic Material ◽  
Crack Tip ◽  
Limit Load ◽  
Material Model ◽  
Crack Tip Opening Displacement ◽  
Opening Displacement ◽  
Elastic Plastic

Abstract This paper provides a numerical analysis of selected parameters of fracture mechanics for double-edge notched specimens in tension, DEN(T), under plane strain conditions. The analysis was performed using the elastic-plastic material model. The study involved determining the stress distribution near the crack tip for both small and large deformations. The limit load solution was verified. The J-integral, the crack tip opening displacement, and the load line displacement were determined using the numerical method to propose the new hybrid solutions for calculating these parameters. The investigations also aimed to identify the influence of the plate geometry and the material characteristics on the parameters under consideration. This paper is a continuation of the author’s previous studies and simulations in the field of elastic-plastic fracture mechanics [4, 6, 16, 17, 31].

Computational Aspect of Nonlinear Fracture Mechanics Application

2015 ◽  
Author(s):  
Igor Orynyak ◽  
Andrii Oryniak
Keyword(s):  
Residual Stress ◽  
Fracture Mechanics ◽  
Thermal Stresses ◽  
Crack Tip ◽  
Pressure Vessels ◽  
Point Of View ◽  
Computational Aspect ◽  
J Integral ◽  
Elastic Plastic ◽  
Plastic Analysis

The development of powerful commercial computer programs made the concept of J-integral as computational parameter of fracture mechanics to be a very attractive one. It is equivalent to SIF in linear case, it converges in numerical calculation and the same results are obtained by different codes (programs). Besides, it is widely thought that elastic-plastic analysis gives bigger values than elastic SIF ones what is good from regulatory point of view. Such stand was reflected in the recommended by IAEA TECDOC 1627 (February 2010) devoted to pressurized thermal shock analysis of reactor pressure vessels, where the embedded crack in FEM mesh, elastic-plastic analysis with simultaneous determination of J-integral was stated as the best option of analysis. But at that time all the most widely used software were not able to treat the residual stresses, the thermal stresses in case of two different materials. Such a contradiction between requirements and the possibilities made a lot of problems for honest contractors especially in countries where the regulator had no own experience in calculation and completely relied on the authority of international documents. This means that at that time the said recommendations were harmful. The main reason of such a situation was the absence of the carefully elaborated examples. Now the capabilities and accuracy of such software are increasing. Nevertheless, some principal ambiguities and divergences of computations results in various J-integral contours around the crack tip still exist. They are exhibited when the large plastic zone emerges at the crack tip. Other problem is influence of the history of loading and the specification of the time of crack insertion in the mesh including the time of emergence of residual stress. This paper is invitation for discussion of the accuracy and restriction of computational J-integral. With this aim the detailed analysis of some simplified 2D examples of calculation of elastic -plastic J-integral for surface crack with accounting for residual stress, thermal stress and inner pressure are performed and commented. The attainment of consensus among the engineering society for treating the outcome results is the prerequisite for practical application of computational elastic plastic J-integral.

Sign in / Sign up

Export Citation Format

Share Document