Influence of prior plastic deformation on the thermal-martensitic-transformation in an Fe-Ni-Al alloy

1987 ◽  
Vol 6 (4) ◽  
pp. 491-494 ◽  
Author(s):  
N. Jost ◽  
E. Hornbogen
Keyword(s):  
Plastic Deformation ◽  
Martensitic Transformation ◽  
Al Alloy ◽  
Prior Plastic Deformation

Effect of Plastic Deformation on the Isothermal FCC/HCP Phase Transformation during Aging of Co-27Cr-5Mo-0.05C Alloy

2007 ◽  
Vol 560 ◽  
pp. 23-28
Author(s):  
A. Mani-Medrano ◽  
Armando Salinas-Rodríguez
Keyword(s):  
Plastic Deformation ◽  
Martensitic Transformation ◽  
Tensile Deformation ◽  
Internal Stresses ◽  
X Ray Diffraction ◽  
Thermally Activated ◽  
Prior Plastic Deformation ◽  
Last Stage ◽  
Isothermal Martensitic Transformation

The effects of tensile deformation on the amount of hcp phase formed during a 3 hour isothermal aging at 800 °C is studied using in-situ X-ray diffraction and scanning electron microscopy. It is shown that the start of the isothermal martensitic transformation during aging of this material is delayed by prior plastic deformation. Nevertheless, the total amount of hcp phase present in the microstructure at the beginning of aging increases at a continuously decreasing rate due to stress-assisted transformation. This behavior is attributed to the relieving of internal stresses produced by plastic deformation prior to aging. Finally, during the last stage of aging, the amount of hcp phase in the microstructure increases as a result of isothermal martensitic transformation. It is suggested that the presence of mechanically-induced hcp phase during aging inhibits the thermally activated nucleation process that leads to the isothermal martensitic transformation.

scholarly journals Evidence of Martensitic Transformation in Fe-Mn-Al Steel Similar to Maraging Steel

2020 ◽  
Vol 52 (1) ◽  
pp. 26-33
Author(s):  
Gurumayum Robert Kenedy ◽  
Yi-Jyun Lin ◽  
Wei-Chun Cheng
Keyword(s):  
Martensitic Transformation ◽  
Maraging Steel ◽  
Trip Steel ◽  
Single Phase ◽  
Lath Martensite ◽  
Al Alloy ◽  
Air Cooling ◽  
Small Temperature Gradient ◽  
Austenite Grains ◽  
Equilibrium Phases

AbstractThe Fe-Mn-Al steels claim a low density, and some fall into the category of transformation-induced plasticity (TRIP) steel. In Fe-Mn-Al TRIP steel development, phase transformations play an important role. Herein, the martensitic transformation of an Fe-16.7 Mn-3.4 Al ternary alloy (wt pct) was experimentally discovered, whose equilibrium phases are a single phase of austenite at 1373 K and dual phases of ferrite and austenite at low temperature. Ferritic lath martensite forms in the prior austenite grains after cooling from 1373 K under various cooling rates via quenching, air cooling, and furnace cooling. The formation mechanism of the ferritic lath martensite is different from that of traditional ferritic lath martensite in steel and quite similar to that in maraging steel. A slight strain energy coupled with a small temperature gradient can lead to the formation of ferritic lath martensite in the Fe-Mn-Al alloy after cooling from high temperature. It is also found that micro-twins exist in the ferritic lath martensite.

Microstructural Change of Beta Type Titanium Alloy by Intense Plastic Deformation

2006 ◽  
Vol 503-504 ◽  
pp. 705-710 ◽  
Author(s):  
Goroh Itoh ◽  
Hisashi Hasegawa ◽  
Tsing Zhou ◽  
Yoshinobu Motohashi ◽  
Mitsuo Niinomi
Keyword(s):  
Plastic Deformation ◽  
Work Hardening ◽  
Static Recrystallization ◽  
True Strain ◽  
Microstructural Change ◽  
Intense Plastic Deformation ◽  
Rolled Plate ◽  
Al Alloy ◽  
Hot Rolled ◽  
Zr Alloy

Usual static recrystallization treatment and a method to provide intense plastic deformation, ARB namely Accumulative Roll-Bonding, have been applied to two beta type titanium alloys, i.e. Ti-29Nb-13Ta-4.6Zr and Ti-15V-3Cr-3Sn-3Al. Microstructural change as well as work-hardening behavior was examined as a function of plastic strain. Both the work-hardening rate and the hardness at the initial as-hot-rolled state were smaller in the Ti-Nb-Ta-Zr alloy than in the Ti-V-Cr-Sn-Al alloy. Recrystallized grains of 14μm in size were obtained by the usual static recrystallization treatment, which was significantly smaller than that of the starting as-hot-rolled plate of 38μm. No significant change other than flattening and elongating of the original grains was found in the optical microscopic scale. It was revealed, however, from a TEM observation combined with selected area diffraction technique that geometric dynamic recrystallization occurred in the Ti-Nb-Ta-Zr alloy deformed at room temperature by a true strain of 5, resulting in an ultra-fine-grained microstructure where the grain size was roughly estimated to be about 100nm.

Ferromagnetism caused by severe plastic deformation of the Fe – 35% Al alloy

2011 ◽  
Vol 53 (12) ◽  
pp. 1325-1330
Author(s):  
Ya. A. Abzgildin ◽  
R. F. Al’mukhametov ◽  
N. G. Zaripov ◽  
H. Ya. Mulyukov
Keyword(s):  
Plastic Deformation ◽  
Severe Plastic Deformation ◽  
Al Alloy
Sign in / Sign up

Export Citation Format

Share Document