Stress-strain and limiting states of flywheels made of composite materials with spokes. Report 4. Experimental verification of calculation dependences

1989 ◽  
Vol 21 (1) ◽  
pp. 119-123
Author(s):  
V. M. Leshchenko ◽  
I. A. Kozlov ◽  
A. P. Pokhil'ko ◽  
A. B. Yudin
Keyword(s):  
Composite Materials ◽  
Experimental Verification ◽  
Stress Strain

scholarly journals A General Temperature-Dependent Stress–Strain Constitutive Model for Polymer-Bonded Composite Materials

Polymers ◽  
2021 ◽  
Vol 13 (9) ◽  
pp. 1393
Author(s):  
Xiaochang Duan ◽  
Hongwei Yuan ◽  
Wei Tang ◽  
Jingjing He ◽  
Xuefei Guan
Keyword(s):  
Composite Materials ◽  
Constitutive Model ◽  
Model Parameters ◽  
Temperature Dependent ◽  
Stress Strain ◽  
Proposed Model ◽  
Single Temperature ◽  
Testing Data ◽  
Bonded Composite ◽  
Tension And Compression

This study develops a general temperature-dependent stress–strain constitutive model for polymer-bonded composite materials, allowing for the prediction of deformation behaviors under tension and compression in the testing temperature range. Laboratory testing of the material specimens in uniaxial tension and compression at multiple temperatures ranging from −40 ∘C to 75 ∘C is performed. The testing data reveal that the stress–strain response can be divided into two general regimes, namely, a short elastic part followed by the plastic part; therefore, the Ramberg–Osgood relationship is proposed to build the stress–strain constitutive model at a single temperature. By correlating the model parameters with the corresponding temperature using a response surface, a general temperature-dependent stress–strain constitutive model is established. The effectiveness and accuracy of the proposed model are validated using several independent sets of testing data and third-party data. The performance of the proposed model is compared with an existing reference model. The validation and comparison results show that the proposed model has a lower number of parameters and yields smaller relative errors. The proposed constitutive model is further implemented as a user material routine in a finite element package. A simple structural example using the developed user material is presented and its accuracy is verified.

Mechanical characterization of a woven multi-layered hyperelastic composite laminate under uniaxial loading

2021 ◽  
pp. 002199832110115
Author(s):  
Shaikbepari Mohmmed Khajamoinuddin ◽  
Aritra Chatterjee ◽  
MR Bhat ◽  
Dineshkumar Harursampath ◽  
Namrata Gundiah
Keyword(s):  
Composite Materials ◽  
Energy Function ◽  
Strain Energy ◽  
Strain Energy Function ◽  
Mechanical Tests ◽  
Stress Strain ◽  
Aerospace Applications ◽  
Envelope Material ◽  
The Individual ◽  
High Dielectric

We characterize the material properties of a woven, multi-layered, hyperelastic composite that is useful as an envelope material for high-altitude stratospheric airships and in the design of other large structures. The composite was fabricated by sandwiching a polyaramid Nomex® core, with good tensile strength, between polyimide Kapton® films with high dielectric constant, and cured with epoxy using a vacuum bagging technique. Uniaxial mechanical tests were used to stretch the individual materials and the composite to failure in the longitudinal and transverse directions respectively. The experimental data for Kapton® were fit to a five-parameter Yeoh form of nonlinear, hyperelastic and isotropic constitutive model. Image analysis of the Nomex® sheets, obtained using scanning electron microscopy, demonstrate two families of symmetrically oriented fibers at 69.3°± 7.4° and 129°± 5.3°. Stress-strain results for Nomex® were fit to a nonlinear and orthotropic Holzapfel-Gasser-Ogden (HGO) hyperelastic model with two fiber families. We used a linear decomposition of the strain energy function for the composite, based on the individual strain energy functions for Kapton® and Nomex®, obtained using experimental results. A rule of mixtures approach, using volume fractions of individual constituents present in the composite during specimen fabrication, was used to formulate the strain energy function for the composite. Model results for the composite were in good agreement with experimental stress-strain data. Constitutive properties for woven composite materials, combining nonlinear elastic properties within a composite materials framework, are required in the design of laminated pretensioned structures for civil engineering and in aerospace applications.

Features of nonlinear in-plane shear deformation of a unidirectional and orthogonally reinforced polymer sheets of composite materials

2021 ◽  
Vol 87 (5) ◽  
pp. 47-55
Author(s):  
A. O. Polovyi ◽  
N. V. Matiushevski ◽  
N. G. Lisachenko
Keyword(s):  
Experimental Data ◽  
Composite Materials ◽  
Shear Modulus ◽  
Maximum Deviation ◽  
Linear Section ◽  
Stress Strain ◽  
Plane Shear ◽  
End Point ◽  
Reinforced Polymer ◽  
Failure Point

A comparative analysis of typical stress-strain diagrams obtained for in-plain shear of the 25 unidirectional and cross-ply reinforced polymer matrix composites under quasi-static loading was carried out. Three of them were tested in the framework of this study, and the experimental data on other materials were taken from the literature. The analysis of the generalized shear-strength curves showed that most of the tested materials exhibit the similar deformation pattern depending on their initial shear modulus: a linear section is observed at the beginning of loading, whereas further increase of the load decreases the slope of the curve reaching the minimum in the failure point. For the three parameters (end point the linear part, maximum reduced deviation of the diagram, tangent shear modulus at the failure point) characterizing the individual features of the presented stress-strain diagrams, approximating their dependences on the value of the reduced initial shear modulus are obtained. At the characteristic points of the deformation diagrams, boundary conditions are determined that can be used to find the parameters of the approximating functions. A condition is proposed for determination of the end point of the linear section on the experimental stress-strain curve, according to which the maximum deviation between the experimental and calculated (according to Hooke’s law) values of the shear stress in this section is no more than 1%, thus ensuring rather high accuracy of approximation on the linear section of the diagram. The results of this study are recommended to use when developing universal and relatively simple in structure approximating functions that take into account the characteristic properties of the experimental curves of deformation of polymer composite materials under in-plane shear of the sheet. The minimum set of experimental data is required to determine the parameters of these functions.

Stress-Strain State Exploration of Stringer Made of Composite Materials Depending on Layers Stacking Structure

2018 ◽  
Vol 284 ◽  
pp. 71-76
Author(s):  
P.V. Solovyev ◽  
A.I. Gomzin ◽  
L.A. Ishbulatov ◽  
S.N. Galyshev ◽  
F.F. Musin
Keyword(s):  
Composite Materials ◽  
Cross Section ◽  
Strain State ◽  
Stress Strain ◽  
Stress Strain State ◽  
Airplane Wing ◽  
External Loads ◽  
Stacking Structure ◽  
Composite Carbon ◽  
Shaped Cross Section

In this article the results of stress-strain state investigation for composite airplane wing stringer with different layers stacking structures are presented. As an object of research, a stringer made of composite carbon with V-shaped cross-section is considered. Due to the stress-strain state analysis of various stringer structures, the most effective structure for stringer layers stacking is selected, both in the view of providing the most rigidity and optimal perception by the stringer the field of external loads, which are most typical for the conditions of its operation.

The Study of Dielectric Constant Inversion of Coconut Fiber/Gypsum Composite Based on the λ/4 Absorption Spectrum

2014 ◽  
Vol 1030-1032 ◽  
pp. 400-403
Author(s):  
Qian Qian Chu ◽  
Hui Chao Zhao ◽  
Wan Jun Hao ◽  
Ying Ying Yi ◽  
Yi Feng Dong ◽  
...  
Keyword(s):  
Dielectric Constant ◽  
Composite Material ◽  
Absorption Spectrum ◽  
Composite Materials ◽  
Experimental Verification ◽  
Complex Permittivity ◽  
Functional Materials ◽  
Coconut Fiber ◽  
Inversion Theory ◽  
Equivalent Complex

The measurement of the complex permittivity of big structure composite material has always been a key and difficulty in the preparation of electromagnetic functional materials. In this paper the average dielectric constant inversion of coconut fiber/gypsum composite in S band is studied based on λ/4 absorption spectrum. First the absorbing effects of the prepared coconut fiber gypsum composite materials are tested with method of flat reflection. Then the equivalent complex permittivity is inversed with the inversion theory. Further the experimental verification is preceded that the theoretical and experimental absorbing curves whose peak positions are respectively at 3.05GHz and 2.45GHz are quite matched. And the study shows that this method is scientific and effective, and it can provide technical support for the baroque electromagnetic functional composite materials.

Sign in / Sign up

Export Citation Format

Share Document