Evaluation of the influence of residual internal microstresses on the strength of 18Kh2N4VA steel with the use of the criterion of tensile stresses

1986 ◽  
Vol 18 (4) ◽  
pp. 482-487 ◽  
Author(s):  
V. M. Mishin ◽  
V. I. Sarrak
Keyword(s):  
Tensile Stresses ◽  
18Kh2n4va Steel ◽  
Internal Microstresses

Variation of Stresses Ahead of The Internal Cracks in ReNI5 Powders During Hydrogen Charging and Discharging Cycles

1997 ◽  
Vol 496 ◽  
Author(s):  
S. B. Biner
Keyword(s):  
Modulus Of Elasticity ◽  
Spherical Particles ◽  
Tensile Stresses ◽  
Hydrogen Charging ◽  
Coupled Diffusion ◽  
Stress States

ABSTRACTIn this study, the evolution of the stress-states ahead of the penny shaped internal cracks in both spherical and disk shaped ReNi5 particles during hydrogen charging and discharging cycles were investigated using coupled diffusion/deformation FEM analyses. The results indicate that large tensile stresses, on the order of 20–50% of the modulus of elasticity, develop in the particles. The disk shaped particles, in addition to having faster charging/discharging cycles, may offer better resistance to fracture than the spherical particles.

scholarly journals Morphology Development and Flow Characteristics during High Moisture Extrusion of a Plant-Based Meat Analogue

Foods ◽  
2021 ◽  
Vol 10 (8) ◽  
pp. 1753
Author(s):  
Patrick Wittek ◽  
Felix Ellwanger ◽  
Heike P. Karbstein ◽  
M. Azad Emin
Keyword(s):  
Transition Zone ◽  
Flow Characteristics ◽  
Phase System ◽  
Shear Stresses ◽  
High Moisture ◽  
Tensile Stresses ◽  
Morphology Development ◽  
A Minor ◽  
Multi Phase ◽  
High Moisture Extrusion

Plant-based meat analogues that mimic the characteristic structure and texture of meat are becoming increasingly popular. They can be produced by means of high moisture extrusion (HME), in which protein-rich raw materials are subjected to thermomechanical stresses in the extruder at high water content (>40%) and then forced through a cooling die. The cooling die, or generally the die section, is known to have a large influence on the products’ anisotropic structures, which are determined by the morphology of the underlying multi-phase system. However, the morphology development in the process and its relationship with the flow characteristics are not yet well understood and, therefore, investigated in this work. The results show that the underlying multi-phase system is already present in the screw section of the extruder. The morphology development mainly takes place in the tapered transition zone and the non-cooled zone, while the cooled zone only has a minor influence. The cross-sectional contraction and the cooling generate elongational flows and tensile stresses in the die section, whereas the highest tensile stresses are generated in the transition zone and are assumed to be the main factor for structure formation. Cooling also has an influence on the velocity gradients and, therefore, the shear stresses; the highest shear stresses are generated towards the die exit. The results further show that morphology development in the die section is mainly governed by deformation and orientation, while the breakup of phases appears to play a minor role. The size of the dispersed phase, i.e., size of individual particles, is presumably determined in the screw section and then stays the same over the die length. Overall, this study reveals that morphology development and flow characteristics need to be understood and controlled for a successful product design in HME, which, in turn, could be achieved by a targeted design of the extruders die section.

Competing fracture modes in brittle materials subject to concentrated cyclic loading in liquid environments: Bilayer structures

2005 ◽  
Vol 20 (10) ◽  
pp. 2792-2800 ◽  
Author(s):  
Sanjit Bhowmick ◽  
Yu Zhang ◽  
Brian R. Lawn
Keyword(s):  
Cyclic Loading ◽  
Driving Forces ◽  
Plate Thickness ◽  
Brittle Materials ◽  
Illustrative Case ◽  
Initial Growth ◽  
Tensile Stresses ◽  
Fracture Modes ◽  
Plate Flexure ◽  
Radial Cracks

A preceding study of the competition between fracture modes in monolithic brittle materials in cyclic loading with curved indenters in liquid environments is here extended to brittle layers on compliant substrates. The fracture modes include outer and inner cone cracks and radial cracks that initiate from the near-contact zone and penetrate downward. Outer cone cracks are driven by stresses from superposed Hertzian and plate flexure fields; inner cone cracks also grow within these fields but are augmented by mechanical driving forces from hydraulic pumping into the crack fissures. Radial cracks are augmented by mechanical driving forces from developing quasiplasticity zones beneath the indenter. Basically, the crack-growth rates are governed by a crack velocity relation. However, the hydraulic and quasiplastic mechanical forces can cumulate in intensity with each cycle, strongly enhancing fatigue. Plate flexure generates compressive stresses at the top surface of the brittle layer, somewhat inhibiting the initiation, and tensile stresses at the lower surface, strongly enhancing the far-field propagation. The tensile stresses promote instability in the crack propagation, resulting in through-thickness penetration (failure). Experiments on a model bilayer system consisting of glass plates bonded to thick polycarbonate bases are presented as an illustrative case study. In situ observations of the crack evolution from initial growth to failure reveal that each fracture mode can dominate under certain test conditions, depending on plate thickness, maximum load, and sphere radius. Implications concerning the failure of practical layer systems, notably dental crowns, are discussed.

Study of Ductile-to-Brittle Transition in Single Grit Diamond Scribing of Silicon: Application to Wire Sawing of Silicon Wafers

2012 ◽  
Vol 134 (4) ◽  
Author(s):  
Hao Wu ◽  
Shreyes N. Melkote
Keyword(s):  
Hydrostatic Pressure ◽  
Silicon Wafers ◽  
Depth Of Cut ◽  
Critical Depth ◽  
External Hydrostatic Pressure ◽  
Tensile Stresses ◽  
Brittle Transition ◽  
Ductile Mode Cutting ◽  
Critical Depth Of Cut ◽  
Ductile To Brittle Transition

The ductile-to-brittle cutting mode transition in single grit diamond scribing of monocrystalline silicon is investigated in this paper. Specifically, the effects of scriber tip geometry, coefficient of friction, and external hydrostatic pressure on the critical depth of cut associated with ductile-to-brittle transition and crack generation are studied via an eXtended Finite Element Method (XFEM) based model, which is experimentally validated. Scribers with a large tip radius are shown to produce lower tensile stresses and a larger critical depth of cut compared with scribers with a sharp tip. Spherical tipped scribers are shown to generate only surface cracks, while sharp tipped scribers (conical, Berkovich and Vickers) are found to create large subsurface tensile stresses, which can lead to nucleation of subsurface median/lateral cracks. Lowering the friction coefficient tends to increase the critical depth of cut and hence the extent of ductile mode cutting. The results also show that larger critical depth of cut can be obtained under external hydrostatic pressure. This knowledge is expected to be useful in optimizing the design and application of the diamond coated wire employed in fixed abrasive diamond wire sawing of photovoltaic silicon wafers.

The Influence of Different Subbase Materials on the Crack of Cement Stabilized Macadam Base during Construction

2012 ◽  
Vol 591-593 ◽  
pp. 955-959 ◽  
Author(s):  
Xiao Feng Liao ◽  
Fen Xiao ◽  
Zhong Da Chen ◽  
Lei Xing
Keyword(s):  
Tensile Stress ◽  
Shrinkage Strain ◽  
Mechanical Parameters ◽  
Tensile Stresses ◽  
Shrinkage Crack ◽  
Dry Shrinkage ◽  
Base Course ◽  
Shrinkage Coefficient ◽  
Crack Space

According to actual axle load data and the measured mechanical parameters of cement stabilized macadam material with different cement dosages, the bottom tensile stresses of different subbase structures are calculated and the results show that: to graded gravel subbase, the weight of construction vehicle is inadvisable to be more than 35t and the cement dosage of base course shall be more than 3.0%; and, the maximum bottom tensile stress of graded gravel subbase shall be much more than that of lime-flyash soil subbase. According to the measured dry shrinkage strain and dry shrinkage coefficient, the dry shrinkage crack space of base course is analyzed and the results show that: under the same cement dosage, the crack space of the base course with graded gravel subbase is smaller than that of lime-flyash soil subbase; with the increase of cement dosage, the crack space of base course increase first and then decrease, and when the cement dosage is 3.5%, the dry shrinkage strain and dry shrinkage coefficient is minimum and the crack space of base course is maximum.

Sign in / Sign up

Export Citation Format

Share Document