Rheological properties of disperse systems at low shear stresses

1982 ◽  
Vol 21 (1) ◽  
pp. 72-80 ◽  
Author(s):  
A. Zosel
1972 ◽  
Vol 5 (6) ◽  
pp. 861-865
Author(s):  
G. M. Bartenev ◽  
L. G. Glukhatkina

1982 ◽  
Vol 24 (6) ◽  
pp. 1488-1494 ◽  
Author(s):  
N.P. Zoteyev ◽  
G.M. Bartenev ◽  
N.V. Yermilova ◽  
O.I. Zoteyeva

2018 ◽  
Vol 42 (3) ◽  
pp. 151-157 ◽  
Author(s):  
Antony P McNamee ◽  
Kieran Richardson ◽  
Jarod Horobin ◽  
Lennart Kuck ◽  
Michael J Simmonds

Introduction: Accumulating evidence demonstrates that subhaemolytic mechanical stresses, typical of circulatory support, induce physical and biochemical changes to red blood cells. It remains unclear, however, whether cell age affects susceptibility to these mechanical forces. This study thus examined the sensitivity of density-fractionated red blood cells to sublethal mechanical stresses. Methods: Red blood cells were isolated and washed twice, with the least and most dense fractions being obtained following centrifugation (1500 g × 5 min). Red blood cell deformability was determined across an osmotic gradient and a range of shear stresses (0.3–50 Pa). Cell deformability was also quantified before and after 300 s exposure to shear stresses known to decrease (64 Pa) or increase (10 Pa) red blood cell deformability. The time course of accumulated sublethal damage that occurred during exposure to 64 Pa was also examined. Results: Dense red blood cells exhibited decreased capacity to deform when compared with less dense cells. Cellular response to mechanical stimuli was similar in trend for all red blood cells, independent of density; however, the magnitude of impairment in cell deformability was exacerbated in dense cells. Moreover, the rate of impairment in cellular deformability, induced by 64 Pa, was more rapid for dense cells. Relative improvement in red blood cell deformability, due to low-shear conditioning (10 Pa), was consistent for both cell populations. Conclusion: Red blood cell populations respond differently to mechanical stimuli: older (more dense) cells are highly susceptible to sublethal mechanical trauma, while cell age (density) does not appear to alter the magnitude of improved cell deformability following low-shear conditioning.


2020 ◽  
Vol 6 (22) ◽  
pp. eaba1529
Author(s):  
Christopher J. Tulley ◽  
Åke Fagereng ◽  
Kohtaro Ujiie

The rheology of the metamorphosed oceanic crust may be a critical control on megathrust strength and deformation style. However, little is known about the strength and deformation style of metamorphosed basalt. Exhumed megathrust shear zones exposed on Kyushu, SW Japan, contain hydrous metabasalts deformed at temperatures between ~300° and ~500°C, spanning the inferred temperature-controlled seismic-aseismic transition. Field and microstructural observations of these shear zones, combined with quartz grain-size piezometry, indicate that metabasalts creep at shear stresses <100 MPa at ~370°C and at shear stresses <30 MPa at ~500°C. These values are much lower than those suggested by viscous flow laws for basalt. The implication is that relatively weak, hydrous, metamorphosed oceanic crust can creep at low viscosities over a wide shear zone and have a critical influence on plate interface strength and deformation style around the seismic-aseismic transition.


1976 ◽  
Vol 55 (3) ◽  
pp. 353-356 ◽  
Author(s):  
M. Braden ◽  
Ratna Perera

Six commercial fluoride gels have been studied, using a cone and plate viscometer. Also, the thickening agents have been analyzed using infrared spectroscopy. All gels showed stress thinning, which is the decrease of viscosity with shear rate. Such shear rate dependence is clinically convenient in that the gel will flow readily at the high shear stresses present when the gel is applied but will not flow readily under its own weight when on the tooth. Five materials containing hydroxyalkyl celluloses showed similar degrees of shear thinning. One material with a non-cellulosic thickener showed much more extreme stress thinning together with elastic behavior at low shear rates; such behavior may be clinically advantageous. All of the gels showed only slight temperature dependence of rheological properties.


2016 ◽  
Vol 256 ◽  
pp. 133-138 ◽  
Author(s):  
Marialaura Tocci ◽  
Christoph Zang ◽  
Ines Cadòrniga Zueco ◽  
Annalisa Pola ◽  
Michael Modigell

Rheological properties of liquid metals are difficult to investigate experimentally because of the extreme border conditions to consider. One difficulty is related to the low viscosity of liquid metals. Surface tension effects can cause forces that can be considerably higher than the viscous forces in the liquid metals. Evaluating the experimental data without considering these effects leads to an apparent shear thinning behavior of the material. In the present study, experiments were performed by means of a Searle rheometer changing the dimension of the measuring system with metals of high surface tension, as mercury and tin. It became evident that surface tension plays a significant role in the effects that falsify measurements at low shear rate. Conclusions can be drawn to what extent measurements of semi-solid metals are affected.


2013 ◽  
Vol 739 ◽  
pp. 117-122
Author(s):  
Hojjatollah Sadeghipour ◽  
Farshid Ghorbani ◽  
Mohammad Reza Jafari Felavarjani ◽  
Hassan Ebadi-Dehaghani ◽  
Davoud Ashouri ◽  
...  

The effect of several types of nanoparticles on the rheological properties of polycarbonate (PC) was compared. Four polycarbonate nanocomposites containing 5 wt% of layered silica (SiO2), Iron oxide (Fe3O4), Iron oxide (α-Fe2O3), cupric oxide (CuO) nanoparticles were prepared via melt compounding at 260 °C. Compression molded samples were prepared and the dynamic rheological properties of the nanocomposites were investigated. The incorporation of the nanoparticles increased the storage modulus and consequently decreased the damping factor. In the Cole-Cole plot, PC filled layered silica and Fe2O3 nanoparticles showed more semi-circle pattern comparing to that of other nanocomposites implied more compatibility between PC and layered silica and also Fe2O3 nanofillers. While other nanocomposites showed more deviation from this pattern. Rotational mode in rheological studies showed that at low shear rate the viscosities of nanocomposites are higher than that of pure Polycarbonate. While at higher shear rate the viscosity of filled samples tend to approach the viscosity of pure PC.


Sign in / Sign up

Export Citation Format

Share Document