Thermoluminescence and Magnetic Properties of irradiated Sodium Chloride

1962 ◽  
Vol 166 (5) ◽  
pp. 577-581 ◽  
Author(s):  
A. Choudhury
Keyword(s):  
Magnetic Properties ◽  
Sodium Chloride

Corrosion of Amorphous Fe73.5Si13.5B9Nb3Cu1 Alloys on the Synergistic Effect of Chloride and Hydroxyl Ions

2011 ◽  
Vol 284-286 ◽  
pp. 1550-1553
Author(s):  
Ming Sheng Li ◽  
Dan Zhang ◽  
Yi Ming Jiang ◽  
Jin Li
Keyword(s):  
Magnetic Properties ◽  
Electrochemical Impedance Spectroscopy ◽  
Sodium Chloride ◽  
Impedance Spectroscopy ◽  
Service Life ◽  
Corrosion Rate ◽  
Electrochemical Impedance ◽  
Soft Magnetic Properties ◽  
High Concentration ◽  
Soft Magnetic

The soft-magnetic properties and service life of amorphous or nanocrystalline Fe73.5Si13.5B9Nb3Cu1 have been influenced by the corrosion of the alloy. In this study, the electrochemical corrosions of amorphous Fe73.5Si13.5B9Nb3Cu1 in the blend solutions of sodium chloride and sodium hydroxide were investigated by linear polarization (PLZ) and electrochemical impedance spectroscopy (EIS) technique. The presence of OH- in the blend solution gave rise to typical passivation of the alloy. A suitable concentration of OH- was required for the low corrosion rate. And the higher concentration of OH- led to a faster corrosion. Increase of concentration of Cl- aroused more obvious corrosion. These results were ascribed to the deteriorating effect of Cl- and high-concentration OH- on the passive film formed on the surface of amorphous Fe73.5Si13.5B9Nb3Cu1.

Morphology and magnetic properties of NiFe 2 O 4 powders prepared in molten sodium chloride

2021 ◽  
Vol 52 (6) ◽  
pp. 677-681
Author(s):  
J.L. Ni ◽  
X. Lin ◽  
Q. Wang ◽  
C.Y. Sun ◽  
F.Y. Du ◽  
...  
Keyword(s):  
Magnetic Properties ◽  
Sodium Chloride ◽  
Molten Sodium

AEM analysis of crystallization in Ti-based amorphous alloys

1983 ◽  
Vol 41 ◽  
pp. 270-271
Author(s):  
A.R. Pelton ◽  
A.F. Marshall ◽  
Y.S. Lee
Keyword(s):  
Magnetic Properties ◽  
Amorphous Alloys ◽  
Amorphous Materials ◽  
Isothermal Annealing ◽  
Amorphous Matrix ◽  
Nucleation And Growth ◽  
Current Interest ◽  
Amorphous Films ◽  
Electrical And Magnetic Properties

Amorphous materials are of current interest due to their desirable mechanical, electrical and magnetic properties. Furthermore, crystallizing amorphous alloys provides an avenue for discerning sequential and competitive phases thus allowing access to otherwise inaccessible crystalline structures. Previous studies have shown the benefits of using AEM to determine crystal structures and compositions of partially crystallized alloys. The present paper will discuss the AEM characterization of crystallized Cu-Ti and Ni-Ti amorphous films.Cu60Ti40: The amorphous alloy Cu60Ti40, when continuously heated, forms a simple intermediate, macrocrystalline phase which then transforms to the ordered, equilibrium Cu3Ti2 phase. However, contrary to what one would expect from kinetic considerations, isothermal annealing below the isochronal crystallization temperature results in direct nucleation and growth of Cu3Ti2 from the amorphous matrix.

Microstructure in soft magnetic E3 (S1, Al) (Sendust) alloys

1988 ◽  
Vol 46 ◽  
pp. 770-771
Author(s):  
June D. Kim
Keyword(s):  
Electron Microscopy ◽  
Magnetic Properties ◽  
Ternary Phase Diagram ◽  
Vertical Tube ◽  
Vacuum Induction Melting ◽  
Induction Melting ◽  
Soft Magnetic ◽  
Quenching Temperature ◽  
Thin Foils ◽  
Vertical Tube Furnace

Iron-base alloys containing 8-11 wt.% Si, 4-8 wt.% Al, known as “Sendust” alloys, show excellent soft magnetic properties. These magnetic properties are strongly dependent on heat treatment conditions, especially on the quenching temperature following annealing. But little has been known about the microstructure and the Fe-Si-Al ternary phase diagram has not been established. In the present investigation, transmission electron microscopy (TEM) has been used to study the microstructure in a Sendust alloy as a function of temperature.An Fe-9.34 wt.% Si-5.34 wt.% Al (approximately Fe3Si0.6Al0.4) alloy was prepared by vacuum induction melting, and homogenized at 1,200°C for 5 hrs. Specimens were heat-treated in a vertical tube furnace in air, and the temperature was controlled to an accuracy of ±2°C. Thin foils for TEM observation were prepared by jet polishing using a mixture of perchloric acid 15% and acetic acid 85% at 10V and ∼13°C. Electron microscopy was performed using a Philips EM 301 microscope.

Magnetic properties of new charge-transfer complexes based on manganese porphyrins

1997 ◽  
Vol 90 (3) ◽  
pp. 407-413
Author(s):  
MARC KELEMEN ◽  
CHRISTOPH WACHTER ◽  
HUBERT WINTER ◽  
ELMAR DORMANN ◽  
RUDOLF GOMPPER ◽  
...  
Keyword(s):  
Magnetic Properties ◽  
Charge Transfer ◽  
Charge Transfer Complexes ◽  
Manganese Porphyrins
Sign in / Sign up

Export Citation Format

Share Document