On the impact end in longitudinal dynamic plastic wave propagation

1978 ◽  
Vol 29 (1-4) ◽  
pp. 75-92 ◽  
Author(s):  
D. W. Nicholson ◽  
A. Phillips
Keyword(s):  
Wave Propagation ◽  
Plastic Wave ◽  
Longitudinal Dynamic ◽  
The Impact

Rails Deformation Pattern in Frontal Impact

2002 ◽  
Author(s):  
Joseph Hassan ◽  
Guy Nusholtz ◽  
Ke Ding
Keyword(s):  
Wave Propagation ◽  
Real World ◽  
Stress Waves ◽  
Stress Wave Propagation ◽  
Deformation Pattern ◽  
Frontal Impact ◽  
Rigid Barrier ◽  
Final Deformation ◽  
Deformation Patterns ◽  
The Impact

During a vehicle crash stress waves can be generated at the impact point and propagate through the vehicle structure. The generation of these waves is dependent, in general, on the crash type and, in particular, on the impact contact characteristics. This has consequences with respect to different crash barrier interfaces for vehicle evaluation. The two barriers most commonly used to evaluate the response of a vehicle in a frontal impact are the rigid barrier and the offset deformable barrier. They constitute different crash modes, full frontal and offset. Consequently it would be expected that there are different deformation patterns between the two. However, an additional possible contributor to the difference is that an impact into a rigid barrier generates waves of significantly greater stress than impacts with the deformable one. If stress waves are a significant component of real world final deformation patterns then, the choice of barrier interface and its effective stiffness is critical. To evaluate this conjecture, models of two types of rails each undergoing two different types of impacts, are analyzed using an explicit dynamic finite element code. Results show that the energy perturbation along the rail depends on the barrier type and that the early phase of wave propagation has very little effect on the final deformation pattern. This implies that in the real world conditions, the stress wave propagation along the rail has very little effect on the final deformed shape of the rail.

scholarly journals A numerical study into the longitudinal dynamic stability of the tailless aircraft

2019 ◽  
Vol 91 (3) ◽  
pp. 428-436 ◽  
Author(s):  
Agnieszka Kwiek
Keyword(s):  
Stability Analysis ◽  
Dynamic Stability ◽  
Numerical Study ◽  
Aircraft Design ◽  
Content Type ◽  
Preliminary Stage ◽  
Longitudinal Dynamic ◽  
Stability Derivatives ◽  
The Impact ◽  
Tailless Aircraft

Purpose The purpose of this research is a study into a mathematical approach of a tailless aircraft dynamic stability analysis. This research is focused on investigation of influence of elevons (elevator) on stability derivatives and consequently on the aircraft longitudinal dynamic stability. The main research question is to determine whether this impact should be taken into account on the conceptual and preliminary stage of the analysis of the longitudinal dynamic stability. Design/methodology/approach Aerodynamic coefficients and longitudinal stability derivatives were computed by Panukl (panel methods). The analysis of the dynamic stability of the tailless aircraft was made by the Matlab code and SDSA package. Findings The main result of the research is a comparison of the dynamic stability of the tailless aircraft for different approaches, with and without the impact of elevator deflection on the trim drag and stability derivatives. Research limitations/implications This paper presents research that mostly should be considered on the preliminary stage of aircraft design and dynamic stability analysis. The impact of elevons deflection on the aircraft moment of inertia has been omitted. Practical implications The results of this research will be useful for the further design of small tailless unmanned aerial vehicles (UAVs). Originality/value This research reveals that in case of the analysis of small tailless UAVs, the impact of elevons deflection on stability derivatives is bigger than the impact of a Mach number. This impact should be taken into consideration, especially for a phugoid mode.

Investigation of Stress Wave Propagation in Brain Tissues Through the Use of Finite Element Method

2010 ◽  
Author(s):  
Biaobiao Zhang ◽  
W. Steve Shepard ◽  
Candace L. Floyd
Keyword(s):  
Finite Element ◽  
Wave Propagation ◽  
Brain Injury ◽  
Stress Wave ◽  
Brain Research ◽  
Complex Structure ◽  
Stress Wave Propagation ◽  
Wave Loads ◽  
The Impact ◽  
The Brain

Because axons serve as the conduit for signal transmission within the brain, research related to axon damage during brain injury has received much attention in recent years. Although myelinated axons appear as a uniform white matter, the complex structure of axons has not been thoroughly considered in the study of fundamental structural injury mechanisms. Most axons are surrounded by an insulating sheath of myelin. Furthermore, hollow tube-like microtubules provide a form of structural support as well as a means for transport within the axon. In this work, the effects of microtubule and its surrounding protein mediums inside the axon structure are considered in order to obtain a better understanding of wave propagation within the axon in an attempt to make progress in this area of brain injury modeling. By examining axial wave propagation using a simplified finite element model to represent microtubule and its surrounding proteins assembly, the impact caused by stress wave loads within the brain axon structure can be better understood. Through conducting a transient analysis as the wave propagates, some important characteristics relative to brain tissue injuries are studied.

Wave Propagation in an Elastic Rod Exhibiting Internal Coulomb Friction, Considered as a Model for a Ring Spring

1956 ◽  
Vol 23 (3) ◽  
pp. 367-372
Author(s):  
E. H. Lee ◽  
A. J. Wang
Keyword(s):  
Wave Propagation ◽  
Stress Wave ◽  
Coulomb Friction ◽  
Stress Wave Propagation ◽  
Infinite Length ◽  
Input Energy ◽  
Elastic Rod ◽  
Total Input ◽  
Conical Bearing ◽  
The Impact

Abstract The problem of stress-wave propagation in a ring spring is considered. A ring spring consists of rings placed normal to the spring axis with alternate internal and external conical bearing surfaces. The friction between these surfaces causes a loading-unloading relation which is strongly irreversible, leading to marked energy absorption for oscillatory stressing. The attenuation of a pulse of stress is analyzed in detail as it is propagated down a spring of infinite length. The influence of certain spring characteristics is evaluated. Concentration of the absorption of the total input energy is found in the region of the impact end of the spring, and particular examples are presented.

Sign in / Sign up

Export Citation Format

Share Document