Sensitivity of centrifugal separator rotor material to stress concentrations

1989 ◽  
Vol 25 (7) ◽  
pp. 367-369
Author(s):  
S. M. Kutepov ◽  
V. A. Mikhailin
Keyword(s):  
Centrifugal Separator ◽  
Stress Concentrations ◽  
Separator Rotor

Sem Examinations of Glass Knives

1970 ◽  
Vol 28 ◽  
pp. 282-283
Author(s):  
J. Temple Black
Keyword(s):  
Plastic Deformation ◽  
Tensile Loading ◽  
Resultant Force ◽  
Stress Concentrations ◽  
Edge Chipping ◽  
Surface Flaws ◽  
Edge Defects ◽  
Microscopic Surface

There are two types of edge defects common to glass knives as typically prepared for microtomy purposes: 1) striations and 2) edge chipping. The former is a function of the free breaking process while edge chipping results from usage or bumping of the edge. Because glass has no well defined planes in its structure, it should be highly resistant to plastic deformation of any sort, including tensile loading. In practice, prevention of microscopic surface flaws is impossible. The surface flaws produce stress concentrations so that tensile strengths in glass are typically 10-20 kpsi and vary only slightly with composition. If glass can be kept in compression, wherein failure is literally unknown (1), it will remain intact for long periods of time. Forces acting on the tool in microtomy produce a resultant force that acts to keep the edge in compression.

Glass Knife Geometry as Seen by the SEM

1971 ◽  
Vol 29 ◽  
pp. 454-455
Author(s):  
J. Temple Black
Keyword(s):  
Low Cost ◽  
Amorphous Material ◽  
Stress Concentrations ◽  
Basic Tool ◽  
Tool Materials ◽  
Optical Inspection ◽  
Surface Flaws ◽  
Slip Planes ◽  
Glass Knife ◽  
Diamond Knife

In ultramicrotomy, the two basic tool materials are glass and diamond. Glass because of its low cost and ease of manufacture of the knife itself is still widely used despite the superiority of diamond knives in many applications. Both kinds of knives produce plastic deformation in the microtomed section due to the nature of the cutting process and microscopic chips in the edge of the knife. Because glass has no well defined slip planes in its structure (it's an amorphous material), it is very strong and essentially never fails in compression. However, surface flaws produce stress concentrations which reduce the strength of glass to 10,000 to 20,000 psi from its theoretical or flaw free values of 1 to 2 million psi. While the microchips in the edge of the glass or diamond knife are generally too small to be observed in the SEM, the second common type of defect can be identified. This is the striations (also termed the check marks or feathers) which are always present over the entire edge of a glass knife regardless of whether or not they are visable under optical inspection. These steps in the cutting edge can be observed in the SEM by proper preparation of carefully broken knives and orientation of the knife, with respect to the scanning beam.

“Cavity” formation in superplastically deformed aluminium alloys

1990 ◽  
Vol 48 (4) ◽  
pp. 958-959
Author(s):  
A. Cziráki ◽  
E. Ková-csetényi ◽  
T. Torma ◽  
T. Turmezey
Keyword(s):  
Grain Boundaries ◽  
Aluminium Alloys ◽  
Superplastic Deformation ◽  
Volume Fraction ◽  
Superplastic Forming ◽  
Polished Surface ◽  
Cavity Formation ◽  
Stress Concentrations ◽  
Electron Microscopic ◽  
Commercial Aluminium

It is known that the formation of cavities during superplastic deformation can be correlated with the development of stress concentrations at irregularities along grain boundaries such as particles, ledges and triple points. In commercial aluminium alloys Al-Fe-Si particles or other coarse constituents may play an important role in cavity formation.Cavity formation during superplastic deformation was studied by optical metallography and transmission scanning electron microscopic investigations on Al-Mg-Si and Al-Mg-Mn alloys. The structure of particles was characterized by selected area diffraction and X-ray micro analysis. The volume fraction of “voids” was determined on mechanically polished surface.It was found by electron microscopy that strongly deformed regions are formed during superplastic forming at grain boundaries and around coarse particles.According to electron diffraction measurements these areas consist of small micro crystallized regions. See Fig.l.Comparing the volume fraction and morphology of cavities found by optical microscopy a good correlation was established between that of micro crystalline regions.

Equilibrium Profile of Modern Belted Radial Ply Tires: Its Determination and Performance Benefits

2013 ◽  
Vol 41 (2) ◽  
pp. 127-151
Author(s):  
Rudolf F. Bauer
Keyword(s):  
Finite Element ◽  
Aspect Ratio ◽  
Finite Element Methods ◽  
Mathematical Analysis ◽  
Internal Stresses ◽  
Stress Concentrations ◽  
Equilibrium Profiles ◽  
Equilibrium Profile ◽  
And Performance ◽  
Beneficial Property

ABSTRACT The benefits of a tire's equilibrium profile have been suggested by several authors in the published literature, and mathematical procedures were developed that represented well the behavior of bias ply tires. However, for modern belted radial ply tires, and particularly those with a lower aspect ratio, the tire constructions are much more complicated and pose new problems for a mathematical analysis. Solutions to these problems are presented in this paper, and for a modern radial touring tire the equilibrium profile was calculated together with the mold profile to produce such tires. Some construction modifications were then applied to these tires to render their profiles “nonequilibrium.” Finite element methods were used to analyze for stress concentrations and deformations within all tires that did or did not conform to equilibrium profiles. Finally, tires were built and tested to verify the predictions of these analyses. From the analysis of internal stresses and deformations on inflation and loading and from the actual tire tests, the superior durability of tires with an equilibrium profile was established, and hence it is concluded that an equilibrium profile is a beneficial property of modern belted radial ply tires.

A new type of cracks adding to Griffith–Irwin cracks

2019 ◽  
Vol 485 (2) ◽  
pp. 162-165
Author(s):  
V. A. Babeshko ◽  
O. M. Babeshko ◽  
O. V. Evdokimova
Keyword(s):  
Stress Intensity Factor ◽  
Stress Intensity ◽  
Intensity Factor ◽  
Crack Tip ◽  
Stress Concentrations ◽  
New Type

The distinctions in the description of the conditions of cracking of materials are revealed. For Griffith–Irwin cracks, fracture is determined by the magnitude of the stress-intensity factor at the crack tip; in the case of the new type of cracks, fracture occurs due to an increase in the stress concentrations up to singular concentrations.

scholarly journals Effect of Crystallographic Orientation and Grain Boundaries on Martensitic Transformation and Superelastic Response of Oligocrystalline Fe–Mn–Al–Ni Shape Memory Alloys

2021 ◽  
Author(s):  
A. Bauer ◽  
M. Vollmer ◽  
T. Niendorf
Keyword(s):  
Martensitic Transformation ◽  
Grain Boundary ◽  
Shape Memory Alloys ◽  
Shape Memory ◽  
Grain Boundaries ◽  
Tensile Tests ◽  
Image Correlation ◽  
Stress Concentrations ◽  
Grain Orientations ◽  
High Degree

AbstractIn situ tensile tests employing digital image correlation were conducted to study the martensitic transformation of oligocrystalline Fe–Mn–Al–Ni shape memory alloys in depth. The influence of different grain orientations, i.e., near-〈001〉 and near-〈101〉, as well as the influence of different grain boundary misorientations are in focus of the present work. The results reveal that the reversibility of the martensite strongly depends on the type of martensitic evolving, i.e., twinned or detwinned. Furthermore, it is shown that grain boundaries lead to stress concentrations and, thus, to formation of unfavored martensite variants. Moreover, some martensite plates seem to penetrate the grain boundaries resulting in a high degree of irreversibility in this area. However, after a stable microstructural configuration is established in direct vicinity of the grain boundary, the transformation begins inside the neighboring grains eventually leading to a sequential transformation of all grains involved.

Effective Convergence Checks for Verifying Finite Element Stresses at Three-Dimensional Stress Concentrations

2018 ◽  
Vol 3 (3) ◽  
Author(s):  
J. R. Beisheim ◽  
G. B. Sinclair ◽  
P. J. Roache
Keyword(s):  
Finite Element ◽  
Error Estimation ◽  
A Posteriori Error Estimates ◽  
Three Dimensional ◽  
Posteriori Error ◽  
Test Problems ◽  
A Posteriori ◽  
Stress Concentrations ◽  
Element Analysis ◽  
A Posteriori Error

Current computational capabilities facilitate the application of finite element analysis (FEA) to three-dimensional geometries to determine peak stresses. The three-dimensional stress concentrations so quantified are useful in practice provided the discretization error attending their determination with finite elements has been sufficiently controlled. Here, we provide some convergence checks and companion a posteriori error estimates that can be used to verify such three-dimensional FEA, and thus enable engineers to control discretization errors. These checks are designed to promote conservative error estimation. They are applied to twelve three-dimensional test problems that have exact solutions for their peak stresses. Error levels in the FEA of these peak stresses are classified in accordance with: 1–5%, satisfactory; 1/5–1%, good; and <1/5%, excellent. The present convergence checks result in 111 error assessments for the test problems. For these 111, errors are assessed as being at the same level as true exact errors on 99 occasions, one level worse for the other 12. Hence, stress error estimation that is largely reasonably accurate (89%), and otherwise modestly conservative (11%).

Sign in / Sign up

Export Citation Format

Share Document