Use of lubricants with filters in rotary drawing of shell-shaped heads

1987 ◽  
Vol 23 (1) ◽  
pp. 34-36
Author(s):  
Yu. I. Kozlov ◽  
Yu. E. Lotarev
Keyword(s):  
Rotary Drawing

Constructive-Technological Features of a Rotary Drawing of Geometrically Complex Hollow Shafts for Gas Turbine Engines

2017 ◽  
Vol 46 (6) ◽  
pp. 596-602 ◽  
Author(s):  
M. I. Nagimov ◽  
Sh. Kh. Mukhtarov ◽  
G. I. Raab ◽  
R. Yu. Sukhorukov ◽  
F. Z. Utyashev
Keyword(s):  
Gas Turbine ◽  
Turbine Engines ◽  
Gas Turbine Engines ◽  
Rotary Drawing ◽  
Geometrically Complex ◽  
Hollow Shafts

Limiting deformation in rotary drawing of anisotropic pipe blanks with wall thinning

2016 ◽  
Vol 36 (6) ◽  
pp. 472-475
Author(s):  
S. S. Yakovlev ◽  
V. I. Tregubov ◽  
E. V. Osipova
Keyword(s):  
Wall Thinning ◽  
Rotary Drawing ◽  
Pipe Blanks

scholarly journals DEVELOPMENT OF THE COMBINED TECHNOLOGICAL PROCESS OF BLANK STACKS FLANGES FORMATION BY THE METHOD OF STAMPING BY ROLLING AND ROTARY DRAWING

2021 ◽  
pp. 111-121
Author(s):  
Viktor Matviychuk ◽  
Mykola Kolisnyk
Keyword(s):  
Technological Process ◽  
Stable Process ◽  
Neck Formation ◽  
Maximum Width ◽  
Distillation Columns ◽  
Compressive Stresses ◽  
Rotary Drawing ◽  
Peripheral Areas ◽  
Plain Strain ◽  
Critical Strains

The article presents the results of the development and research of the combined technological process of forming the outer and inner flanges of the lids of fractional and distillation columns on sheet blanks by the method of stamping by rolling and rotary drawing. For this purpose, equipment has been developed that allows to form both outer and inner flanges of the blank in one run of the conical roll. Studies have shown that technological capabilities of the process are limited by the risk of destruction of the top layers of the outer flange bending center and its corrugation, as well as by the neck formation or destruction of the peripheral areas of the inner flange. To assess the deformability of the outer flange, the stress-strain state of its bending center was investigated. According to the set stress values, the stress state of the material is determined, the maximum value of which on the surface of the bending zone is Formula for determining the minimum radius of the mandrel, which when using the values of the critical ductility of the material allows to prevent destruction. As well, an expression for determining the maximum width of the flange, provided that the destruction of peripheral areas is prevented, is obtained. As corrugations formation is the main danger in forming the external flanges by the stamping by rolling method (SR), the expression for determining the maximum width of the flange under the condition of a stable process is obtained. If it is necessary to get more developed flanges, it is proposed to provide thinning of their walls by rotary extraction at the second stage. When forming the inner flanges of the blank stacks radial compressive stresses and tangential tensile stresses in the material are brought about. The action of tangential stresses causes loss of stability of the flange by way of neck formation. The value of the critical strains increases with the approach to the state of plain-strain deformation. Therefore, it is recommended to develop process parameters based on construction of the critical strains diagrams.

Rotary drawing of axisymmetric shells with distribution of the deformation zone

2015 ◽  
Vol 35 (4) ◽  
pp. 270-276 ◽  
Author(s):  
S. S. Yakovlev ◽  
V. I. Tregubov ◽  
O. V. Pilipenko ◽  
K. S. Remnev
Keyword(s):  
Deformation Zone ◽  
Rotary Drawing ◽  
Axisymmetric Shells

scholarly journals Relationship of the method of obtaining the original billet with the accuracy of manufacturing of the extended axisymmetric bodies

2020 ◽  
pp. 25-28
Author(s):  
A. S. Yamnikov ◽  
E. N. Rodionova ◽  
I. A. Matveev
Keyword(s):  
Heat Treatment ◽  
Quality Parameters ◽  
Rolled Stock ◽  
Low Temperature Annealing ◽  
Rotary Drawing ◽  
Output Quality ◽  
Statistical Studies ◽  
Hot Rolled ◽  
Relationship Of ◽  
Axisymmetric Bodies

A comparative description of the technology for producing blanks for the artillery shell cases or the rocket shell bodies using flat rolled stock or rolled tubular products is given. It is noted that the lower cost of flat rolled stock leads to its wider application for stamping blanks of cartridge caps or bodies, including cutting a circle from flat rolled stock, convolution and several transitions of drawing, alternating with heat treatment. It is noted that the disadvantage of this technology are the errors in the shape of the blanks, amounting to 0.75÷1.5 of the tolerance for diametrical dimensions. When machining, these errors decrease according to the laws of copying the errors, however, the anisotropy of the material of the part blank leads to the appearance of errors in the shape-ovality and curvature of the pipe, which lead to the formation of a large radial runout of the prefabricated rocket body. It has been found that the scattering fields of all output quality parameters exceed the existing tolerances: radial runout of the assembled body by 1.3 times; ovality of the middle centering bulge by 2.15 times. It is shown that the technological process of manufacturing prefabricated housings using initial blanks from flat rolled stock does not provide the required precision technology reliability. For the manufacture of monolithic extended axisymmetric bodies, hot-rolled thickwalled pipes are used as an initial billet. The operations are performed in the following sequence: cutting pipes into dimensional workpieces; machining (turning, boring); heat treatment (quenching, tempering); machining (fine turning, boring); rotary drawing (first and second transitions); crimping the thickening; low temperature annealing. Statistical studies have found a regression equation showing at a confidence level β = 0.95, dependence of the diameter of the base hole of the workpiece after drawing in from the current value of the diameter before drawing.

Sign in / Sign up

Export Citation Format

Share Document