The state of stress of an anisotropic half-plane with an elliptic inclusion

1993 ◽  
Vol 65 (6) ◽  
pp. 1995-2002
Author(s):  
L. G. Smirnov ◽  
S. V. Priimak ◽  
I. I. Fedik
Keyword(s):  
Half Plane ◽  
The State ◽  
Elliptic Inclusion ◽  
State Of Stress

scholarly journals Half-plane contacts subject to remote tension

2021 ◽  
pp. 030932472098844
Author(s):  
Nils Cwiekala ◽  
David A Hills
Keyword(s):  
Contact Problem ◽  
Half Plane ◽  
Asymptotic Form ◽  
Fretting Fatigue ◽  
The State ◽  
Partial Slip ◽  
Practical Relevance ◽  
Plane Contact ◽  
State Of Stress ◽  
Plane Contact Problem

The state of stress present in an elastic half-plane contact problem, where one or both bodies is subject to remote tension has been investigated, both for conditions of full stick and partial slip. The state of stress present near the contact edges is studied for different loading scenarios in an asymptotic form. This is of practical relevance to the study of contacts experiencing fretting fatigue, and enables the environment in which cracks nucleate to be specified.

The state of stress near the singularities created by a plane punch

1978 ◽  
Vol 13 (4) ◽  
pp. 231-236 ◽  
Author(s):  
N P Andrianopoulos ◽  
P S Theocaris
Keyword(s):  
Stress Distribution ◽  
Half Plane ◽  
Taylor Series ◽  
Stress Function ◽  
Complex Stress ◽  
The State ◽  
Singular Points ◽  
State Of Stress ◽  
Contact Surfaces ◽  
Complex Stress Function

An attempt is made to obtain photoelastically the stress distribution in the near vicinity of singular points, when a punch is indenting an elastic half-plane. The punch is to be assumed flat and rough so that friction is developed between the contact surfaces. By expanding the complex stress function into a Taylor series, an extrapolation law is obtained, which allows the calculation of stresses at the vicinity of the singular points by means of photoelastic measurements at positions remote from these points. The error limits of this technique are defined and, finally, a relation between the order of singularity and the parameters of the photoelastic pattern is established.

scholarly journals Effect of the Rock Stress on the Water Jet Cutting Performance

2021 ◽  
Author(s):  
Battista Grosso ◽  
Valentina Dentoni ◽  
Augusto Bortolussi
Keyword(s):  
Numerical Models ◽  
Step Function ◽  
Water Jet ◽  
The State ◽  
Cutting Performance ◽  
Lagrangian Analysis ◽  
State Of Stress ◽  
Water Jet Cutting ◽  
Cutting Rate ◽  
Available Technology

AbstractUnderground quarrying is rarely adopted for granite extraction due to the difficulties in the implementation of traditional technologies (drilling and explosive). As alternative to drilling and explosive, the combination of diamond wire and water jet seems to be the most promising available technology. The cutting performance achievable with the water jet technology depends on the operative parameters, the material characteristics and the state of stress within the rock massif. To assess the effect of the state of stress on the cutting rate, laboratory tests have been performed with an oscillating water jet machine on granite samples subjected to a static load. The stress distribution in the layer of rock to be removed has been evaluated by numerical simulation with the FLAC code (Fast Lagrangian Analysis of Continua). The correlation between the results of the cutting tests and the numerical models of the rock samples has been inferred. Starting from a conceptual model, which theoretically describes the relationship between the cutting rate and the stress, a step function was defined that indicates the ranges of stress where predefined values of the cutting rate are workable.

scholarly journals Sub-Level Stoping in an Underground Limestone Quarry: An Analysis of the State of Stress in an Evolutionary Scenario

2016 ◽  
Vol 61 (1) ◽  
pp. 199-216 ◽  
Author(s):  
Marilena Cardu ◽  
Sergio Dipietromaria ◽  
Pierpaolo Oreste
Keyword(s):  
Numerical Models ◽  
The State ◽  
In Situ Tests ◽  
Future Scenario ◽  
Limestone Quarry ◽  
Geomechanical Properties ◽  
State Of Stress ◽  
Upper Level ◽  
Pillar Structure

Abstract The aim of this study was to evaluate the state of stress of a „voids-pillar“ structure excavated by means of the sub-level stoping method in an underground limestone quarry near Bergamo (Italy). Both the current structure of the quarry (i.e. the rooms exploited till now) and a possible future scenario were analysed using the (FDM) FLAC 2D code. The quarry has been in operation since 1927; at present, exploitation is carried out underground via the sub-level stoping method. Exploitation involves two levels, with 5 rooms on the upper level and 9 rooms on the lower level. After analysing data obtained from laboratory and in situ tests carried out on rock samples and natural discontinuities, the geomechanical properties of the medium, knowledge of which is essential in order to establish the parameters that must be included in the numerical model, were evaluated. The implementation of three numerical models made it possible to study both the present conditions of quarry exploitation and the evolution of the exploited rooms, as well as a possible expansion involving a third level of rooms. Using the results obtained regarding the stress-strain present in the pillars, a potential change in room geometry was proposed aimed at reducing the stress state inside the pillars, decreasing plasticity and increasing overall quarry safety.

Experimental Determination of the Two-Dimensional State of Stress and the Orthotropic Elasticity Coefficients for Coatings

1990 ◽  
Vol 203 ◽  
Author(s):  
Richard J. Farris ◽  
M. A. Maden ◽  
K. Tong
Keyword(s):  
Elastic Constants ◽  
Physical Property ◽  
The State ◽  
Normal Stresses ◽  
Free Standing ◽  
Vibrationally Excited ◽  
Plane Shear ◽  
Plane Normal ◽  
State Of Stress ◽  
The One

ABSTRACTThe state of stress for a uniform coating away from the edges reduces to that of plane stress, two in-plane normal stresses, and an in-plane shear stress. For this state, the interface between the coating and the substrate is totally stress free. Since the substrate and the coating are not interacting mechanically, an internal section of the substrate can be removed creating a tensioned drum-like membrane without altering the stress state. Holographic interferometry of vibrationally excited membranes is used to evaluate the stress. Using this technique, up to thirty vibrational modes can be obtained. This high degree of redundancy enables one to determine the one shear and two normal stresses that act in the plane of the coating. The only physical property requires is the coating density. The density is obtained from commonly reported literature values. Simple variations on the membrane vibration scheme, e.g., cutting the membrane to create a uniaxially tensioned ribbon, enables one to determine the in-plane Poisson's ratio and shearmodulus.In separate but related experiments on commercially made free-standing films with residual orientation, the above techniques, combined with special free and axially constrainedcompressibility experiments should enable all of the Poisson's ratios and elasticmoduli for an orthotropic material (nine elastic constants) to be determined. Methods for measuring the state of stress and the elastic constants are required to predict the state of stress in complex coating geometries.

Sign in / Sign up

Export Citation Format

Share Document