Two-dimensional flow in porous strata with conductivity varying discontinuously along second-order curves

1993 ◽  
Vol 28 (1) ◽  
pp. 90-97
Author(s):  
V. F. Piven'
Keyword(s):  
Second Order ◽  
Two Dimensional ◽  
Dimensional Flow ◽  
Two Dimensional Flow ◽  
Porous Strata

AVERAGING PRINCIPLE FOR QUASI-LINEAR PARABOLIC PDEs AND RELATED DIFFUSION PROCESSES

2012 ◽  
Vol 12 (01) ◽  
pp. 1150008 ◽  
Author(s):  
MARK FREIDLIN ◽  
LEONID KORALOV
Keyword(s):  
Small Parameter ◽  
Diffusion Processes ◽  
First Integral ◽  
Second Order ◽  
Averaging Principle ◽  
Two Dimensional ◽  
Parabolic Pdes ◽  
Dimensional Flow ◽  
Linear Perturbations ◽  
Two Dimensional Flow

Quasi-linear perturbations of a two-dimensional flow with a first integral and the corresponding parabolic PDEs with a small parameter at the second-order derivatives are considered in this paper.

Two-Dimensional Flow of Polymer Solutions Through Porous Media

1999 ◽  
Vol 2 (3) ◽  
pp. 251-262
Author(s):  
P. Gestoso ◽  
A. J. Muller ◽  
A. E. Saez
Keyword(s):  
Porous Media ◽  
Polymer Solutions ◽  
Two Dimensional ◽  
Dimensional Flow ◽  
Two Dimensional Flow

STUDY OF NON-ISOTHERMAL TWO-DIMENSIONAL FLOW OVER A SQUARE CYLINDER IMMERSED IN A CHANNEL

2019 ◽  
Author(s):  
Gabriel Machado dos Santos ◽  
Ítalo Augusto Magalhães de Ávila ◽  
Hélio Ribeiro Neto ◽  
João Marcelo Vedovoto
Keyword(s):  
Two Dimensional ◽  
Square Cylinder ◽  
Dimensional Flow ◽  
Two Dimensional Flow

scholarly journals Two-dimensional flow field distribution characteristics of flocking drainage pipes in tunnel

Open Physics ◽  
2020 ◽  
Vol 18 (1) ◽  
pp. 139-148
Author(s):  
Shiyang Liu ◽  
Xuefu Zhang ◽  
Feng Gao ◽  
Liangwen Wei ◽  
Qiang Liu ◽  
...  
Keyword(s):  
Flow Field ◽  
Field Distribution ◽  
Rapid Development ◽  
Maximum Velocity ◽  
Distribution Characteristics ◽  
Two Dimensional ◽  
Dimensional Flow ◽  
Laboratory Test Results ◽  
Transverse Distance ◽  
Two Dimensional Flow

AbstractWith the rapid development of traffic infrastructure in China, the problem of crystal plugging of tunnel drainage pipes becomes increasingly salient. In order to build a mechanism that is resilient to the crystal plugging of flocking drainage pipes, the present study used the numerical simulation to analyze the two-dimensional flow field distribution characteristics of flocking drainage pipes under different flocking spacings. Then, the results were compared with the laboratory test results. According to the results, the maximum velocity distribution in the flow field of flocking drainage pipes is closely related to the transverse distance h of the fluff, while the longitudinal distance h of the fluff causes little effect; when the transverse distance h of the fluff is less than 6.25D (D refers to the diameter of the fluff), the velocity between the adjacent transverse fluffs will be increased by more than 10%. Moreover, the velocity of the upstream and downstream fluffs will be decreased by 90% compared with that of the inlet; the crystal distribution can be more obvious in the place with larger velocity while it is less at the lower flow rate. The results can provide theoretical support for building a mechanism to deal with and remove the crystallization of flocking drainage pipes.

Contracting ducts of finite length

1951 ◽  
Vol 2 (4) ◽  
pp. 254-271 ◽  
Author(s):  
L. G. Whitehead ◽  
L. Y. Wu ◽  
M. H. L. Waters
Keyword(s):  
Stream Function ◽  
Finite Length ◽  
Velocity Potential ◽  
Three Dimensional ◽  
Relaxation Method ◽  
Two Dimensional ◽  
Dimensional Flow ◽  
Hodograph Plane ◽  
Two Dimensional Flow ◽  
Working Section

SummmaryA method of design is given for wind tunnel contractions for two-dimensional flow and for flow with axial symmetry. The two-dimensional designs are based on a boundary chosen in the hodograph plane for which the flow is found by the method of images. The three-dimensional method uses the velocity potential and the stream function of the two-dimensional flow as independent variables and the equation for the three-dimensional stream function is solved approximately. The accuracy of the approximate method is checked by comparison with a solution obtained by Southwell's relaxation method.In both the two and the three-dimensional designs the curved wall is of finite length with parallel sections upstream and downstream. The effects of the parallel parts of the channel on the rise of pressure near the wall at the start of the contraction and on the velocity distribution across the working section can therefore be estimated.

Sign in / Sign up

Export Citation Format

Share Document