Structure of the reaction zone of a two-phase detonation

1978 ◽  
Vol 12 (3) ◽  
pp. 481-484
Author(s):  
A. M. Gladilin
Keyword(s):  
Reaction Zone ◽  
Two Phase

Position of the reaction zone in polyesterification in two phase systems

1979 ◽  
Vol 21 (6) ◽  
pp. 1540-1545 ◽  
Author(s):  
T.V. Kudim ◽  
L.B. Sokolov ◽  
V.S. Naumov ◽  
A.N. Shevchenko
Keyword(s):  
Reaction Zone ◽  
Two Phase ◽  
Phase Systems

Detonation reaction zone in two-phase mixtures

1970 ◽  
Vol 6 (3) ◽  
pp. 327-336 ◽  
Author(s):  
A. A. Borisov ◽  
B. E. Gel'fand ◽  
S. A. Gubin ◽  
S. M. Kogarko ◽  
A. L. Podgrebenkov
Keyword(s):  
Reaction Zone ◽  
Two Phase ◽  
Detonation Reaction

Stability of homogeneous-solid deflagration with two-phase flow in the reaction zone

1990 ◽  
Vol 79 (2) ◽  
pp. 199-213 ◽  
Author(s):  
Stephen B. Margolis ◽  
Forman A. Williams
Keyword(s):  
Reaction Zone ◽  
Two Phase Flow ◽  
Phase Flow ◽  
Two Phase

Effect of Shock Loading on the Microstructure of Uniloy 326

1974 ◽  
Vol 32 ◽  
pp. 504-505
Author(s):  
K. P. Staudhammer ◽  
L. E. Murr
Keyword(s):  
Grain Size ◽  
Shock Loading ◽  
Current Investigation ◽  
Two Phase ◽  
05 C ◽  
Shock Deformation ◽  
Heat Treated

The effect of shock loading on a variety of steels has been reviewed recently by Leslie. It is generally observed that significant changes in microstructure and microhardness are produced by explosive shock deformation. While the effect of shock loading on austenitic, ferritic, martensitic, and pearlitic structures has been investigated, there have been no systematic studies of the shock-loading of microduplex structures.In the current investigation, the shock-loading response of millrolled and heat-treated Uniloy 326 (thickness 60 mil) having a residual grain size of 1 to 2μ before shock loading was studied. Uniloy 326 is a two phase (microduplex) alloy consisting of 30% austenite (γ) in a ferrite (α) matrix; with the composition.3% Ti, 1% Mn, .6% Si,.05% C, 6% Ni, 26% Cr, balance Fe.

Exsolution and inversion in pigeonite from the Whin Sill, Northern England

1978 ◽  
Vol 36 (1) ◽  
pp. 474-475
Author(s):  
P.P.K. Smith
Keyword(s):  
High Temperature ◽  
Low Temperature ◽  
Homogeneous Nucleation ◽  
Silicate Mineral ◽  
Antiphase Boundaries ◽  
Two Phase ◽  
Primitive Form ◽  
The Core ◽  
Nucleation Mechanisms ◽  
And Inversion

Grains of pigeonite, a calcium-poor silicate mineral of the pyroxene group, from the Whin Sill dolerite have been ion-thinned and examined by TEM. The pigeonite is strongly zoned chemically from the composition Wo8En64FS28 in the core to Wo13En34FS53 at the rim. Two phase transformations have occurred during the cooling of this pigeonite:- exsolution of augite, a more calcic pyroxene, and inversion of the pigeonite from the high- temperature C face-centred form to the low-temperature primitive form, with the formation of antiphase boundaries (APB's). Different sequences of these exsolution and inversion reactions, together with different nucleation mechanisms of the augite, have created three distinct microstructures depending on the position in the grain.In the core of the grains small platelets of augite about 0.02μm thick have farmed parallel to the (001) plane (Fig. 1). These are thought to have exsolved by homogeneous nucleation. Subsequently the inversion of the pigeonite has led to the creation of APB's.

TEM characterization of reaction zone in a SiC fiber-reinforced titanium alloy

1988 ◽  
Vol 46 ◽  
pp. 738-739
Author(s):  
G. Das ◽  
R. E. Omlor
Keyword(s):  
Titanium Alloys ◽  
Reaction Zone ◽  
Carbon Layer ◽  
Fiber Reinforced ◽  
Reaction Products ◽  
Sic Fibers ◽  
Sic Fiber ◽  
The Matrix ◽  
Immense Potential

Fiber reinforced titanium alloys hold immense potential for applications in the aerospace industry. However, chemical reaction between the fibers and the titanium alloys at fabrication temperatures leads to the formation of brittle reaction products which limits their development. In the present study, coated SiC fibers have been used to evaluate the effects of surface coating on the reaction zone in the SiC/IMI829 system.IMI829 (Ti-5.5A1-3.5Sn-3.0Zr-0.3Mo-1Nb-0.3Si), a near alpha alloy, in the form of PREP powder (-35 mesh), was used a茸 the matrix. CVD grown AVCO SCS-6 SiC fibers were used as discontinuous reinforcements. These fibers of 142μm diameter contained an overlayer with high Si/C ratio on top of an amorphous carbon layer, the thickness of the coating being ∽ 1μm. SCS-6 fibers, broken into ∽ 2mm lengths, were mixed with IMI829 powder (representing < 0.1vol%) and the mixture was consolidated by HIP'ing at 871°C/0. 28GPa/4h.

Shock consolidation of Ni-Ti alloy powder

1986 ◽  
Vol 44 ◽  
pp. 430-431
Author(s):  
Naresh N. Thadhani ◽  
Thad Vreeland ◽  
Thomas J. Ahrens
Keyword(s):  
Alloy Powder ◽  
Amorphous Material ◽  
Ti Alloy ◽  
Two Phase ◽  
Near Surface ◽  
Optical Micrograph ◽  
Shock Compaction ◽  
Powder Particles ◽  
Ti Powder ◽  
Rapidly Solidified

A spherically-shaped, microcrystalline Ni-Ti alloy powder having fairly nonhomogeneous particle size distribution and chemical composition was consolidated with shock input energy of 316 kJ/kg. In the process of consolidation, shock energy is preferentially input at particle surfaces, resulting in melting of near-surface material and interparticle welding. The Ni-Ti powder particles were 2-60 μm in diameter (Fig. 1). About 30-40% of the powder particles were Ni-65wt% and balance were Ni-45wt%Ti (estimated by EMPA).Upon shock compaction, the two phase Ni-Ti powder particles were bonded together by the interparticle melt which rapidly solidified, usually to amorphous material. Fig. 2 is an optical micrograph (in plane of shock) of the consolidated Ni-Ti alloy powder, showing the particles with different etching contrast.

A Comparison of Tem and Apfim to the Interpretation of Modulated Microstructures

1985 ◽  
Vol 43 ◽  
pp. 70-71
Author(s):  
M.G. Burke ◽  
M.K. Miller
Keyword(s):  
Low Temperature ◽  
Microstructural Characterization ◽  
Superlattice Reflection ◽  
High Volume ◽  
Atom Probe ◽  
Dark Field ◽  
Miscibility Gap ◽  
Second Phase ◽  
Two Phase ◽  
Probe Field

Interpretation of fine-scale microstructures containing high volume fractions of second phase is complex. In particular, microstructures developed through decomposition within low temperature miscibility gaps may be extremely fine. This paper compares the morphological interpretations of such complex microstructures by the high-resolution techniques of TEM and atom probe field-ion microscopy (APFIM).The Fe-25 at% Be alloy selected for this study was aged within the low temperature miscibility gap to form a <100> aligned two-phase microstructure. This triaxially modulated microstructure is composed of an Fe-rich ferrite phase and a B2-ordered Be-enriched phase. The microstructural characterization through conventional bright-field TEM is inadequate because of the many contributions to image contrast. The ordering reaction which accompanies spinodal decomposition in this alloy permits simplification of the image by the use of the centered dark field technique to image just one phase. A CDF image formed with a B2 superlattice reflection is shown in fig. 1. In this CDF micrograph, the the B2-ordered Be-enriched phase appears as bright regions in the darkly-imaging ferrite. By examining the specimen in a [001] orientation, the <100> nature of the modulations is evident.

A TEM study of the influence of microstructure on the superplastic behavior of a U-5.8 wt.% Nb alloy

1986 ◽  
Vol 44 ◽  
pp. 568-569
Author(s):  
G. Mackiewicz Ludtka
Keyword(s):  
Grain Size ◽  
Heating Rate ◽  
Phase Field ◽  
Single Phase ◽  
Superplastic Behavior ◽  
Two Phase ◽  
Single Phase Field

Historically, metals exhibit superplasticity only while forming in a two-phase field because a two-phase microstructure helps ensure a fine, stable grain size. In the U-5.8 Nb alloy, superplastici ty exists for up to 2 h in the single phase field (γ1) at 670°C. This is above the equilibrium monotectoid temperature of 647°C. Utilizing dilatometry, the superplastic (SP) U-5.8 Nb alloy requires superheating to 658°C to initiate the α+γ2 → γ1 transformation at a heating rate of 1.5°C/s. Hence, the U-5.8 Nb alloy exhibits an anomolous superplastic behavior.

Sign in / Sign up

Export Citation Format

Share Document