Attractancy toOryzaephilus surinamensis (L.) of volatile materials isolated from vacuum distillate of heat-treated carobs

1985 ◽  
Vol 11 (5) ◽  
pp. 565-581 ◽  
Author(s):  
M. R. Stubbs ◽  
J. Chambers ◽  
S. B. Schofield ◽  
J. P. G. Wilkins
Keyword(s):  
Vacuum Distillate ◽  
Heat Treated ◽  
Volatile Materials

scholarly journals The Roles of Amino Acids and Sugars in the Production of Volatile Materials in Microwave Heated Tobacco Dust Suspensions

1997 ◽  
Vol 17 (3) ◽  
pp. 75-95 ◽  
Author(s):  
WM Coleman ◽  
TA Perfetti
Keyword(s):  
Amino Acids ◽  
Amino Acid ◽  
Volatile Compounds ◽  
Reaction Pathways ◽  
Low Molecular Weight ◽  
Heat Treated ◽  
Strecker Aldehyde ◽  
Major Reaction ◽  
First Time ◽  
Volatile Materials

AbstractFor the first time, the role(s) of selected amino acids and sugars in the production of volatile compounds in microwave prepared heat treated tobacco suspensions (HTTS) has been unambiguously defined. The role can be expressed in two major reaction pathways:1) Strecker degradation of amino acids and 2) amino acid/sugar Maillard-type reactions. The mechanism of the Strecker degradation was confirmed by the addition of selected13C- labelled amino acids to the reaction suspension. The addition of the amino acid resulted in a dramatic increase in the concentration of the specific, appropriate, low molecular weight Strecker aldehyde in the headspace above the reaction suspension. The mechanism of the amino acid/sugar Maillard-type reactions was substantiated by: 1) adding a wide array of amino acids to the suspension;2) by employing15N-labelled amino acids; and3) employing13C-labelled sugars. Addition of amino acids to the suspension followed by heat treatment resulted in significant increases (2 ×) in the concentration of volatile pyrazines relative to the control. Most amino acids significantly increased the concentration of headspace pyrazines. Reactivity differences, as a function of sugars, was also demonstrated. Analysis of the headspace above suspensions incorporating15N-labelled amino acids and13C-labelled sugars revealed the15N and13C atoms to have been distributed throughout a wide array of volatile pyrazines. The distribution of the15N atoms within the pyrazines was unique to the amino acid and the distribution of the 13C atoms was linked to the type of sugar employed. These results have documented for the first time in a heat treated tobacco formulation the mechanisms of amino acids and sugars in the production of volatile compounds which have documented intense sensory characteristics.

Direct Observation of Crystalline Ordering In Naturally Graphitized Carbon Produced by Low Grade Metamorphism

1977 ◽  
Vol 35 ◽  
pp. 162-163
Author(s):  
Thomas R. McKee ◽  
Peter R. Buseck
Keyword(s):  
Crystallite Size ◽  
Sedimentary Rocks ◽  
Carbonaceous Material ◽  
Low Grade ◽  
X Ray ◽  
Graphitized Carbon ◽  
Transmission Electron ◽  
Heat Treated ◽  
Commercial Carbon ◽  
Metamorphic Zone

Sediments commonly contain organic material which appears as refractory carbonaceous material in metamorphosed sedimentary rocks. Grew and others have shown that relative carbon content, crystallite size, X-ray crystallinity and development of well-ordered graphite crystal structure of the carbonaceous material increases with increasing metamorphic grade. The graphitization process is irreversible and appears to be continous from the amorphous to the completely graphitized stage. The most dramatic chemical and crystallographic changes take place within the chlorite metamorphic zone.The detailed X-ray investigation of crystallite size and crystalline ordering is complex and can best be investigated by other means such as high resolution transmission electron microscopy (HRTEM). The natural graphitization series is similar to that for heat-treated commercial carbon blacks, which have been successfully studied by HRTEM (Ban and others).

Effect of Shock Loading on the Microstructure of Uniloy 326

1974 ◽  
Vol 32 ◽  
pp. 504-505
Author(s):  
K. P. Staudhammer ◽  
L. E. Murr
Keyword(s):  
Grain Size ◽  
Shock Loading ◽  
Current Investigation ◽  
Two Phase ◽  
05 C ◽  
Shock Deformation ◽  
Heat Treated

The effect of shock loading on a variety of steels has been reviewed recently by Leslie. It is generally observed that significant changes in microstructure and microhardness are produced by explosive shock deformation. While the effect of shock loading on austenitic, ferritic, martensitic, and pearlitic structures has been investigated, there have been no systematic studies of the shock-loading of microduplex structures.In the current investigation, the shock-loading response of millrolled and heat-treated Uniloy 326 (thickness 60 mil) having a residual grain size of 1 to 2μ before shock loading was studied. Uniloy 326 is a two phase (microduplex) alloy consisting of 30% austenite (γ) in a ferrite (α) matrix; with the composition.3% Ti, 1% Mn, .6% Si,.05% C, 6% Ni, 26% Cr, balance Fe.

Phase Transformation In Ti-6al-4v Alloys

1972 ◽  
Vol 30 ◽  
pp. 584-585
Author(s):  
Shiro Fujishiro
Keyword(s):  
Phase Transformation ◽  
Grain Boundary ◽  
Cryogenic Temperature ◽  
Β Phase ◽  
Heat Treated ◽  
Mixed Microstructure ◽  
Ductile Behavior

The Ti-6 wt.% Al-4 wt.% V commercial alloys have exhibited an improved formability at cryogenic temperature when the alloys were heat-treated prior to the tests. The author was interested in further investigating this unusual ductile behavior which may be associated with the strain-induced transformation or twinning of the a phase, enhanced at lower temperatures. The starting materials, supplied by RMI Co., Niles, Ohio were rolled mill products in the form of 40 mil sheets. The microstructure of the as-received materials contained mainly ellipsoidal α grains measuring between 1 and 5μ. The β phase formed an undefined grain boundary around the a grains. The specimens were homogenized at 1050°C for one hour, followed by aging at 500°C for two hours, and then quenched in water to produce the α/β mixed microstructure.

Microstructural Evolution in Reduced TiO2

1981 ◽  
Vol 39 ◽  
pp. 74-75
Author(s):  
W. T. Donlon ◽  
S. Shinozaki ◽  
E. M. Logothetis ◽  
W. Kaizer
Keyword(s):  
Microstructural Evolution ◽  
Point Defects ◽  
Extended Defects ◽  
Small Deviations ◽  
Controlled Atmospheres ◽  
Limited Solubility ◽  
Thin Foils ◽  
Heat Treated ◽  
Porous Polycrystalline ◽  
Crystallographic Shear

Since point defects have a limited solubility in the rutile (TiO2) lattice, small deviations from stoichiometry are known to produce crystallographic shear (CS) planes which accomodate local variations in composition. The material used in this study was porous polycrystalline TiO2 (60% dense), in the form of 3mm. diameter disks, 1mm thick. Samples were mechanically polished, ion-milled by conventional techniques, and initially examined with the use of a Siemens EM102. The electron transparent thin foils were then heat-treated under controlled atmospheres of CO/CO2 and H2 and reexamined in the same manner.The “as-received” material contained mostly TiO2 grains (∼5μm diameter) which had no extended defects. Several grains however, aid exhibit a structure similar to micro-twinned grains observed in reduced rutile. Lattice fringe images (Fig. 1) of these grains reveal that the adjoining layers are not simply twin related variants of a single TinO2n-1 compound. Rather these layers (100 - 250 Å wide) are alternately comprised of stoichiometric TiO2 (rutile) and reduced TiO2 in the form of Ti8O15, with the Ti8O15 layers on either side of the TiO2 being twin related.

Characterization of carbides in M50NiL

1991 ◽  
Vol 49 ◽  
pp. 606-607
Author(s):  
L. S. Lin ◽  
K. P. Gumz ◽  
A. V. Karg ◽  
C. C. Law
Keyword(s):  
Temperature Effects ◽  
Base Composition ◽  
Lattice Parameter ◽  
Control Surface ◽  
Carbide Formation ◽  
Particle Sizes ◽  
Low Carbon ◽  
Fee Structure ◽  
Heat Treated

Carbon and temperature effects on carbide formation in the carburized zone of M50NiL are of great importance because they can be used to control surface properties of bearings. A series of homogeneous alloys (with M50NiL as base composition) containing various levels of carbon in the range of 0.15% to 1.5% (in wt.%) and heat treated at temperatures between 650°C to 1100°C were selected for characterizations. Eleven samples were chosen for carbide characterization and chemical analysis and their identifications are listed in Table 1.Five different carbides consisting of M6C, M2C, M7C3 and M23C6 were found in all eleven samples examined as shown in Table 1. M6C carbides (with least carbon) were found to be the major carbide in low carbon alloys (<0.3% C) and their amounts decreased as the carbon content increased. In sample C (0.3% C), most particles (95%) encountered were M6C carbide with a particle sizes range between 0.05 to 0.25 um. The M6C carbide are enriched in both Mo and Fe and have a fee structure with lattice parameter a=1.105 nm (Figure 1).

Formation Mechanisms for Multiply Twinned Particles During Nucleation in the Au/MICA System

1975 ◽  
Vol 33 ◽  
pp. 84-85
Author(s):  
Eal H. Lee ◽  
Helmut Poppa
Keyword(s):  
Deposition Time ◽  
High Vacuum ◽  
Dark Field ◽  
Ultra High Vacuum ◽  
Formation Mechanisms ◽  
Heat Treated ◽  
Cluster Density ◽  
Diffraction Patterns ◽  
Crystal Particle ◽  
Multiply Twinned Particles

The formation of thin films of gold on mica has been studied in ultra-high vacuum (5xl0-10 torr) . The mica substrates were heat-treated for 24 hours at 375°C, cleaved, and annealed for 15 minutes at the deposition temperature of 300°C prior to deposition. An impingement flux of 3x1013 atoms cm-2 sec-1 was used. These conditions were found to give high number densities of multiple twin particles and are based on a systematic series of nucleation experiments described elsewhere. Individual deposits of varying deposition time were made and examined by bright and dark field TEM after "cleavage preparation" of highly transparent specimens. In the early stages of growth, the films generally consist of small particles which are either single crystals or multiply twinned; a strong preference for multiply twinned particles was found whenever the particle number densities were high. Fig. 1 shows the stable cluster density ns and the variation with deposition time of multiple twin particle and single crystal particle densities, respectively. Corresponding micrographs and diffraction patterns are shown in Fig. 2.

Effect of a Complex Heat Treatment on the Structure of 300M Steel

1981 ◽  
Vol 39 ◽  
pp. 312-313
Author(s):  
R. Padmanabhan ◽  
W. E. Wood
Keyword(s):  
Heat Treatment ◽  
Metal Carbides ◽  
Austenite Grain Size ◽  
300M Steel ◽  
Heat Treated ◽  
Strain Fracture ◽  
Prior Austenite Grain Size ◽  
Short Time ◽  
Final Tempering ◽  
Similar Yield

Intermediate high temperature tempering prior to subsequent reaustenitization has been shown to double the plane strain fracture toughness as compared to conventionally heat treated UHSLA steels, at similar yield strength levels. The precipitation (during tempering) of metal carbides and their subsequent partial redissolution and refinement (during reaustenitization), in addition to the reduction in the prior austenite grain size during the cycling operation have all been suggested to contribute to the observed improvement in the mechanical properties. In this investigation, 300M steel was initially austenitized at 1143°K and then subjected to intermediate tempering at 923°K for 1 hr. before reaustenitizing at 1123°K for a short time and final tempering at 583°K. The changes in the microstructure responsible for the improvement in the properties have been studied and compared with conventionally heat treated steel. Fig. 1 shows interlath films of retained austenite produced during conventionally heat treatment.

Carbide precipitation and chromium depletion on coherent twin boundaries in deformed 304 stainless steels

1992 ◽  
Vol 50 (2) ◽  
pp. 1216-1217
Author(s):  
A.H. Advani ◽  
L.E. Murr ◽  
D.J. Matlock ◽  
W.W. Fisher ◽  
P.M. Tarin ◽  
...  
Keyword(s):  
Grain Boundaries ◽  
Stainless Steels ◽  
Interfacial Free Energy ◽  
Carbide Precipitation ◽  
Twin Boundaries ◽  
Invariant Structure ◽  
Heat Treated ◽  
Constant Structure ◽  
Cr Depletion

Coherent annealing-twin boundaries are constant structure and energy interfaces with an average interfacial free energy of ∼19mJ/m2 versus ∼210 and ∼835mJ/m2 for incoherent twins and “regular” grain boundaries respectively in 304 stainless steels (SS). Due to their low energy, coherent twins form carbides about a factor of 100 slower than grain boundaries, and limited work has also shown differences in Cr-depletion (sensitization) between twin versus grain boundaries. Plastic deformation, may, however, alter the kinetics and thermodynamics of twin-sensitization which is not well understood. The objective of this work was to understand the mechanisms of carbide precipitation and Cr-depletion on coherent twin boundaries in deformed SS. The research is directed toward using this invariant structure and energy interface to understand and model the role of interfacial characteristics on deformation-induced sensitization in SS. Carbides and Cr-depletion were examined on a 20%-strain, 0.051%C-304SS, heat treated to 625°C-4.5h, as described elsewhere.

Sign in / Sign up

Export Citation Format

Share Document