Multilayer spherical shell subjected to a uniformly distributed load over the area

1970 ◽  
Vol 6 (7) ◽  
pp. 738-744
Author(s):  
E. I. Trush
Keyword(s):  
Spherical Shell ◽  
Distributed Load ◽  
Uniformly Distributed Load

scholarly journals Effects of additional load at different heights on gait initiation: A statistical parametric mapping of center of pressure and center of mass behavior

PLoS ONE ◽  
2021 ◽  
Vol 16 (6) ◽  
pp. e0242892
Author(s):  
Marcus Fraga Vieira ◽  
Fábio Barbosa Rodrigues ◽  
Alfredo de Oliveira Assis ◽  
Eduardo de Mendonça Mesquita ◽  
Thiago Santana Lemes ◽  
...  
Keyword(s):  
Time Series ◽  
Center Of Pressure ◽  
Center Of Mass ◽  
Statistical Parametric Mapping ◽  
Gait Initiation ◽  
Experimental Conditions ◽  
Distributed Load ◽  
Uniformly Distributed Load ◽  
Reaction Forces ◽  
Controlled Object

The purpose of this study was to investigate the effects of different vertical positions of an asymmetrical load on the anticipatory postural adjustments phase of gait initiation. Sixty-eight college students (32 males, 36 females; age: 23.65 ± 3.21 years old; weight: 69.98 ± 8.15 kg; height: 1.74 ± 0.08 m) were enrolled in the study. Ground reaction forces and moments were collected using two force platforms. The participants completed three trials under each of the following random conditions: no-load (NL), waist uniformly distributed load (WUD), shoulder uniformly distributed load (SUD), waist stance foot load (WST), shoulder stance foot load (SST), waist swing foot load (WSW), and shoulder swing foot load (SSW). The paired Hotelling’s T-square test was used to compare the experimental conditions. The center of pressure (COP) time series were significantly different for the SUD vs. NL, SST vs. NL, WST vs. NL, and WSW vs. NL comparisons. Significant differences in COP time series were observed for all comparisons between waist vs. shoulder conditions. Overall, these differences were greater when the load was positioned at the shoulders. For the center of mass (COM) time series, significant differences were found for the WUD vs. NL and WSW vs. NL conditions. However, no differences were observed with the load positioned at the shoulders. In conclusion, only asymmetrical loading at the waist produced significant differences, and the higher the extra load, the greater the effects on COP behavior. By contrast, only minor changes were observed in COM behavior, suggesting that the changes in COP (the controller) behavior are adjustments to maintain the COM (controlled object) unaltered.

scholarly journals Analysis of Cantilever Beam Deflection under Uniformly Distributed Load using Artificial Neural Networks

2019 ◽  
Vol 255 ◽  
pp. 06004
Author(s):  
T.M.Y.S Tuan Ya ◽  
Reza Alebrahim ◽  
Nadziim Fitri ◽  
Mahdi Alebrahim
Keyword(s):  
Neural Networks ◽  
Artificial Neural Networks ◽  
Cantilever Beam ◽  
Training Data ◽  
Beam Deflection ◽  
Problem Solver ◽  
Distributed Load ◽  
Uniformly Distributed Load ◽  
Non Linear ◽  
Artificial Neural

In this study the deflection of a cantilever beam was simulated under the action of uniformly distributed load. The large deflection of the cantilever beam causes the non-linear behavior of beam. The prupose of this study is to predict the deflection of a cantilever beam using Artificial Neural Networks (ANN). The simulation of the deflection was carried out in MATLAB by using 2-D Finite Element Method (FEM) to collect the training data for the ANN. The predicted data was then verified again through a non linear 2-D geometry problem solver, FEM. Loads in different magnitudes were applied and the non-linear behaviour of the beam was then recorded. It was observed that, there is a close agreement between the predicted data from ANN and the results simulated in the FEM.

scholarly journals Calculation of orthotropic plates for creep taking into account shear deformations

2018 ◽  
Vol 196 ◽  
pp. 01002 ◽  
Author(s):  
Anton Chepurnenko ◽  
Batyr Yazyev ◽  
Angelica Saibel
Keyword(s):  
Differential Equations ◽  
Transverse Shear ◽  
System Of Differential Equations ◽  
Orthotropic Plates ◽  
Shear Deformations ◽  
Tangential Stresses ◽  
Distributed Load ◽  
Uniformly Distributed Load ◽  
Basic Hypothesis

A system of differential equations is obtained for calculating the creep of orthotropic plates taking into account the deformations of the transverse shear. The basic hypothesis is a parabolic change in tangential stresses over the thickness of the plate. An example of the calculation is given for a GRP plate hinged on the contour under the action of a uniformly distributed load.

Parallelogrammic elements in the solution of rhombic cantilever plate problems

1966 ◽  
Vol 1 (3) ◽  
pp. 223-230 ◽  
Author(s):  
D. J. Dawe
Keyword(s):  
Finite Element Method ◽  
Finite Element ◽  
Natural Frequencies ◽  
Cantilever Plate ◽  
Plate Element ◽  
The Finite Element Method ◽  
Skew Angle ◽  
Distributed Load ◽  
Uniformly Distributed Load ◽  
Element Method

The finite element method is applied to the calculation of the deflection under a uniformly distributed load and the natural frequencies of the rhombic cantilever plate. This has required the derivation of stiffness and inertia matrices for a plate element of parallelogrammic planform. Although, in common with the work of past investigators, the accuracy of the results decreases with increase in skew angle it is shown that the method is adequate for angles up to about 45°.

Sign in / Sign up

Export Citation Format

Share Document