Temperature stresses in a heat-source heated plate strip with heat transfer

1967 ◽  
Vol 3 (3) ◽  
pp. 48-54 ◽  
Author(s):  
Yu. M. Kolyano ◽  
E. A. Pakula
Keyword(s):  
Heat Transfer ◽  
Heat Source ◽  
Heated Plate ◽  
Temperature Stresses ◽  
Plate Strip

scholarly journals EFFECT OF NON-UNIFORM HEAT SOURCE AND RADIATION ON UNSTEADY MHD FREE CONVECTION FLOW PAST AN INFINITE HEATED VERTICAL PLATE IN POROUS MEDIUM

2020 ◽  
Vol 9 (4) ◽  
pp. 219
Author(s):  
PRATIBHA MISHRA ◽  
SWETA TRIPATHI
Keyword(s):  
Heat Transfer ◽  
Porous Medium ◽  
Heat Source ◽  
Free Convection ◽  
Skin Friction ◽  
Time Dependent ◽  
Convection Flow ◽  
Heated Plate ◽  
Free Convection Flow ◽  
Uniform Heat

Influence of radiation and non-uniform heat source on unsteady, magneto-hydrodynamic free convection flow of viscous incompressible fluid past an infinite vertical heated plate embedded in porous medium of an optically thin environment with time dependent suction and viscous dissipation is investigated in this paper. Analytical solutions of the coupled non-linear equations are obtained for the velocity field and temperature distribution using oscillating time-dependent perturbation technique. Expressions for skin-friction and heat transfer rate are also derived. The effects of the material parameters on velocity, temperature, skin-friction, and rate of heat transfer are discussed quantitatively.

scholarly journals Parametric analysis of the heat transfer behavior of the nano-particle ionic-liquid flow between concentric cylinders

2021 ◽  
Vol 13 (6) ◽  
pp. 168781402110240
Author(s):  
Rehan Ali Shah ◽  
Hidayat Ullah ◽  
Muhammad Sohail Khan ◽  
Aamir Khan
Keyword(s):  
Heat Transfer ◽  
Ionic Liquid ◽  
Partial Differential Equations ◽  
Differential Equations ◽  
Heat Source ◽  
Ordinary Differential Equations ◽  
Heat Transfer Rate ◽  
Transfer Rate ◽  
Volume Fraction ◽  
Concentric Cylinders

This paper investigates the enhanced viscous behavior and heat transfer phenomenon of an unsteady two di-mensional, incompressible ionic-nano-liquid squeezing flow between two infinite parallel concentric cylinders. To analyze heat transfer ability, three different type nanoparticles such as Copper, Aluminum [Formula: see text], and Titanium oxide [Formula: see text] of volume fraction ranging from 0.1 to 0.7 nm, are added to the ionic liquid in turns. The Brinkman model of viscosity and Maxwell-Garnets model of thermal conductivity for nano particles are adopted. Further, Heat source [Formula: see text], is applied between the concentric cylinders. The physical phenomenon is transformed into a system of partial differential equations by modified Navier-Stokes equation, Poisson equation, Nernst-Plank equation, and energy equation. The system of nonlinear partial differential equations, is converted to a system of coupled ordinary differential equations by opting suitable transformations. Solution of the system of coupled ordinary differential equations is carried out by parametric continuation (PC) and BVP4c matlab based numerical methods. Effects of squeeze number ( S), volume fraction [Formula: see text], Prandtle number (Pr), Schmidt number [Formula: see text], and heat source [Formula: see text] on nano-ionicliquid flow, ions concentration distribution, heat transfer rate and other physical quantities of interest are tabulated, graphed, and discussed. It is found that [Formula: see text] and Cu as nanosolid, show almost the same enhancement in heat transfer rate for Pr = 0.2, 0.4, 0.6.

scholarly journals Analysis and Comparison of Some Low-Temperature Heat Sources for Heat Pumps

Energies ◽  
2019 ◽  
Vol 12 (10) ◽  
pp. 1853 ◽  
Author(s):  
Pavel Neuberger ◽  
Radomír Adamovský
Keyword(s):  
Heat Transfer ◽  
Low Temperature ◽  
Heat Source ◽  
Heat Pump ◽  
Heat Exchangers ◽  
Ambient Air ◽  
Heat Transfer Fluid ◽  
Heat Sources ◽  
Ground Heat Exchangers ◽  
Temperature Heat

The efficiency of a heat pump energy system is significantly influenced by its low-temperature heat source. This paper presents the results of operational monitoring, analysis and comparison of heat transfer fluid temperatures, outputs and extracted energies at the most widely used low temperature heat sources within 218 days of a heating period. The monitoring involved horizontal ground heat exchangers (HGHEs) of linear and Slinky type, vertical ground heat exchangers (VGHEs) with single and double U-tube exchanger as well as the ambient air. The results of the verification indicated that it was not possible to specify clearly the most advantageous low-temperature heat source that meets the requirements of the efficiency of the heat pump operation. The highest average heat transfer fluid temperatures were achieved at linear HGHE (8.13 ± 4.50 °C) and double U-tube VGHE (8.13 ± 3.12 °C). The highest average specific heat output 59.97 ± 41.80 W/m2 and specific energy extracted from the ground mass 2723.40 ± 1785.58 kJ/m2·day were recorded at single U-tube VGHE. The lowest thermal resistance value of 0.07 K·m2/W, specifying the efficiency of the heat transfer process between the ground mass and the heat transfer fluid, was monitored at linear HGHE. The use of ambient air as a low-temperature heat pump source was considered to be the least advantageous in terms of its temperature parameters.

Sign in / Sign up

Export Citation Format

Share Document