Effect of orthotropy on the stress distribution near a hole in a conical shell

1979 ◽  
Vol 15 (6) ◽  
pp. 544-547
Author(s):  
P. Z. Lugovoi
Keyword(s):  
Stress Distribution ◽  
Conical Shell

The concerted use of SEM, TEM, and SCM for examination of resin-dentin interfaces

1994 ◽  
Vol 52 ◽  
pp. 476-477
Author(s):  
B. Van Meerbeek ◽  
L. J. Conn ◽  
E. S. Duke
Keyword(s):  
Surface Layer ◽  
Stress Distribution ◽  
Phosphoric Acid ◽  
Bonding Mechanism ◽  
Restorative Dentistry ◽  
Dental Adhesive ◽  
Low Viscosity ◽  
Dentin Adhesives ◽  
Acid Etch ◽  
Tooth Tissue

Restoration of decayed teeth with tooth-colored materials that can be bonded to tooth tissue has been a highly desirable property in restorative dentistry for many years. Advantages of such an adhesive restorative technique over conventional techniques using non-adhesive metal-based restoratives include improved restoration retention with minimal sacrifice of sound tooth tissue for retention purposes, superior adaptation and sealing of the restoration margins in prevention of caries recurrence, improved stress distribution across the tooth-restoration interface throughout the whole tooth, and even reinforcement of weakened tooth structures. The dental adhesive technology is rapidly changing. An efficient resin bond to enamel has already long been achieved. Its bonding mechanism has been fully elucidated and has proven to be a durable and reliable clinical treatment. However, bonding to dentin represents a greater challenge. After the failures of a dentin acid-etch technique in imitation of the enamel phosphoric-acid-etch technique and a bonding procedure based on chemical adhesion, modern dentin adhesives are currently believed to bond to dentin by a micromechanical hybridization process. This process is developed by an initial demineralization of the dentin surface layer with acid etchants exposing a collagen fibril arrangement with interfibrillar microporosities that subsequently become impregnated by low-viscosity monomers. Although the development of such a hybridization process has well been documented in the literature, questions remain with respect to parameters of-primary importance to adhesive efficacy.

ANALYSIS OF THE INFLUENCE OF DIMENSIONS OF THE ROPE MIDWATER TRAWLS ON THEIR PERFORMANCE SUBJECT TO GEOMETRIC PROPERTIES OF CONE SHELLS

2017 ◽  
pp. 25-33
Author(s):  
Alexander Vasilievich Dvernik
Keyword(s):  
Surface Properties ◽  
Conical Shell ◽  
Side Surface ◽  
Theoretic Analysis ◽  
Good Convergence ◽  
Large Size ◽  
Quality Coefficient ◽  
Geometric Quality ◽  
The Relationship ◽  
Parameters Calculation

The article studies different shell constructions of mid-water trawls and their properties. The problem settled is suggested to be solved taking into account real geometric interrelations between spacious and surface properties of cone shells. The author suggests to accept a so-called geometric quality coefficient as a criterion of the properties of a conical shell, which represents the ratio of the shell to the area of its side surface and by analogy to use it to the shell of the trawl. The relationship between the trawl dimensions and geometric quality coefficient have been studied. Comparing these figures with the actual characteristics of trawls showed good convergence. According to the results of theoretic analysis and parameters calculation, trawl large-size shells will always have advantages in geometric characteristics over mid-size and, especially, small-size shells. The results of the analysis can be used for approximate calculations of the parameters of the trawl and justification of ways to improve the performance of existing mid-water trawls.

Stress Distribution of a Large Deck Block During Turnover

1975 ◽  
Vol 1975 (138) ◽  
pp. 349-355
Author(s):  
Yoshiro Manabe ◽  
Yasuhiko Ono ◽  
Yoshikatsu Kitamura ◽  
Nobukazu Kozai ◽  
Nobuo Mori
Keyword(s):  
Stress Distribution
Sign in / Sign up

Export Citation Format

Share Document