Numerical modeling of supersonic two-phase jet flows with explicit separation of shock waves

1987 ◽  
Vol 53 (1) ◽  
pp. 763-767
Author(s):  
�. I. Vitkin ◽  
L. T. Perel'man ◽  
Yu. V. Khodyko
Keyword(s):  
Numerical Modeling ◽  
Shock Waves ◽  
Jet Flows ◽  
Two Phase

The Numerical Modeling of Spherical Explosion in the Foam

2016 ◽  
Vol 11 (1) ◽  
pp. 60-65 ◽  
Author(s):  
R.Kh. Bolotnova ◽  
E.F. Gainullina
Keyword(s):  
Shock Wave ◽  
Numerical Modeling ◽  
Initial Pressure ◽  
Water Volume ◽  
Symmetric Model ◽  
Two Phase ◽  
Experimental Conditions ◽  
Initial Water ◽  
Aqueous Foam ◽  
Spherical Explosion

The spherical explosion propagation process in aqueous foam with the initial water volume content α10=0.0083 corresponding to the experimental conditions is analyzed numerically. The solution method is based on the one-dimensional two-temperature spherically symmetric model for two-phase gas-liquid mixture. The numerical simulation is built by the shock capturing method and movable Lagrangian grids. The amplitude and the width of the initial pressure pulse are found from the amount of experimental explosive energy. The numerical modeling results are compared to the real experiment. It’s shown, that the foam compression in the shock wave leads to the significant decrease in velocity and in amplitude of the shock wave.

Numerical Modeling of Evolution of Boundary Between Incompressible Gas and Liquid in Two-Dimensional Region

2006 ◽  
Vol 4 ◽  
pp. 224-236
Author(s):  
A.S. Topolnikov
Keyword(s):  
Numerical Modeling ◽  
Interphase Boundary ◽  
Incompressible Liquid ◽  
Stokes Equations ◽  
Numerical Code ◽  
Navier Stokes ◽  
Two Phase ◽  
Navier Stokes Equations ◽  
Incompressible Media ◽  
Good Agreement

The paper is devoted to numerical modeling of Navier–Stokes equations for incompressible media in the case, when there exist gas and liquid inside the rectangular calculation region, which are separated by interphase boundary. The set of equations for incompressible liquid accounting for viscous, gravitational and surface (capillary) forces is solved by finite-difference scheme on the spaced grid, for description of interphase boundary the ideology of Level Set Method is used. By developed numerical code the set of hydrodynamic problems is solved, which describe the motion of two-phase incompressible media with interphase boundary. As a result of numerical simulation the solutions are obtained, which are in good agreement with existing analytical and experimental solutions.

Features of spatial shock-wave flows in vapor-gas-liquid mixtures

2014 ◽  
Vol 10 ◽  
pp. 27-31
Author(s):  
R.Kh. Bolotnova ◽  
U.O. Agisheva ◽  
V.A. Buzina
Keyword(s):  
Shock Wave ◽  
High Pressure ◽  
Shock Waves ◽  
Liquid Mixture ◽  
Liquid Mixtures ◽  
Pressure Vessels ◽  
Water Mixture ◽  
Two Dimensional ◽  
Nonstationary Processes ◽  
Two Phase

The two-phase model of vapor-gas-liquid medium in axisymmetric two-dimensional formulation, taking into account vaporization is constructed. The nonstationary processes of boiling vapor-water mixture outflow from high-pressure vessels as a result of depressurization are studied. The problems of shock waves action on filled by gas-liquid mixture volumes are solved.

Numerical modeling of two-phase binary fluid mixing using mixed finite elements

2012 ◽  
Vol 16 (4) ◽  
pp. 1101-1124 ◽  
Author(s):  
Shuyu Sun ◽  
Abbas Firoozabadi ◽  
Jisheng Kou
Keyword(s):  
Numerical Modeling ◽  
Finite Elements ◽  
Mixed Finite Elements ◽  
Fluid Mixing ◽  
Two Phase ◽  
Binary Fluid

Experimental and Numerical Modeling of Gaseous Carbon Dioxide Injecting Into Aqueous Water in Bottle Filler System

2001 ◽  
Author(s):  
Y. H. Zheng ◽  
R. S. Amano
Keyword(s):  
Carbon Dioxide ◽  
Numerical Modeling ◽  
Tap Water ◽  
Co2 Injection ◽  
Operating Characteristics ◽  
Two Phase ◽  
Carbonation Process ◽  
Filling System ◽  
Gas System ◽  
Gaseous Carbon Dioxide

Abstract An efficient enhancement of the carbonation rate in the bottle filling stage can substantially increase the production in beverage industries. The bottle filling system currently used in most of the manufacturers can still be improved for a better performance of carbonation by designing the injection tube system. This paper reports on an experimental and numerical mass transfer modeling that can simulate the dissolution process of gaseous carbon dioxide into aqueous water in the bottle filler system. In order to establish the operating characteristics of the bottle filler system, an ordinary tap water and pure carbon dioxide were used as the liquid-gas system. The two-phase numerical modeling was developed that can serve as a framework for the continuous improvement of the design of the carbonation process in the bottle filler system. For an optimal design of CO2 injection tube and flow conditions, a computational fluid dynamics (CFD) approach is one of the most power tools. However, since only limited experimental data are available in the open literature to verify the computational results, an experiment study was performed to obtain measurements of CO2 level, temperature, and pressure during the carbonation process in the bottle filled with liquid. Both experimental and numerical studies of various flow condition and different sizes of injection tube are presented in this paper.

Analysis of Transient Two-Phase Flow in Pressure Safety Valve Outlet Headers

2018 ◽  
Author(s):  
Maral Taghva ◽  
Lars Damkilde
Keyword(s):  
Steady State ◽  
Shock Waves ◽  
High Speed ◽  
Two Phase Flow ◽  
Safety Valve ◽  
Strong Shock ◽  
Flow Property ◽  
Phase Flow ◽  
Transient Pressure ◽  
Two Phase

To protect a pressurized system from overpressure, one of the most established strategies is to install a Pressure Safety Valve (PSV). Therefore, the excess pressure of the system is relieved through a vent pipe when PSV opens. The vent pipe is also called “PSV Outlet Header”. After the process starts, a transient two-phase flow is formed inside the outlet header consisting of high speed pressurized gas interacting with existing static air. The high-speed jet compresses the static air towards the end tail of the pipe until it is discharged to the ambiance and eventually, the steady state is achieved. Here, this transient process is investigated both analytically and numerically using the method of characteristics. Riemann’s solvers and Godunov’s method are utilized to establish the solution. Propagation of shock waves and flow property alterations are clearly demonstrated throughout the simulations. The results show strong shock waves as well as high transient pressure take place inside the outlet header. This is particularly important since it indicates the significance of accounting for shock waves and transient pressure, in contrast to commonly accepted steady state calculations. More precisely, shock waves and transient pressure could lead to failure, if the pipe thickness is chosen only based on conventional steady state calculations.

Sign in / Sign up

Export Citation Format

Share Document