Optimal winding of filament-wound reinforced plastic shells designed to resist buckling under external pressure or axial compression

1972 ◽  
Vol 4 (4-6) ◽  
pp. 696-704
Author(s):  
V. I. Mikisheva
Keyword(s):  
Axial Compression ◽  
External Pressure ◽  
Filament Wound ◽  
Reinforced Plastic

Buckling of Circular Cylindrical Shells Using a Displacement Function

1974 ◽  
Vol 96 (4) ◽  
pp. 1322-1327
Author(s):  
Shun Cheng ◽  
C. K. Chang
Keyword(s):  
Boundary Conditions ◽  
Axial Compression ◽  
Cylindrical Shells ◽  
External Pressure ◽  
Displacement Function ◽  
Combined Loading ◽  
Trial Solution ◽  
Governing Differential Equation ◽  
Circular Cylindrical Shells ◽  
The Stability

The buckling problem of circular cylindrical shells under axial compression, external pressure, and torsion is investigated using a displacement function φ. A governing differential equation for the stability of thin cylindrical shells under combined loading of axial compression, external pressure, and torsion is derived. A method for the solutions of this equation is also presented. The advantage in using the present equation over the customary three differential equations for displacements is that only one trial solution is needed in solving the buckling problems as shown in the paper. Four possible combinations of boundary conditions for a simply supported edge are treated. The case of a cylinder under axial compression is carried out in detail. For two types of simple supported boundary conditions, SS1 and SS2, the minimum critical axial buckling stress is found to be 43.5 percent of the well-known classical value Eh/R3(1−ν2) against the 50 percent of the classical value presently known.

Enhancement of vibration characteristics in filament wound FRP composite shafts using nitinol wires

2018 ◽  
Vol 47 (5) ◽  
pp. 377-385 ◽  
Author(s):  
Kannan Murugesan ◽  
Kalaichelvan K. ◽  
M.P. Jenarthanan ◽  
Sornakumar T.
Keyword(s):  
Natural Frequency ◽  
Damping Ratio ◽  
Filament Winding ◽  
Fiber Reinforced ◽  
Content Type ◽  
Fiber Reinforced Plastic ◽  
Damping Characteristics ◽  
Filament Wound ◽  
Reinforced Plastic ◽  
Hollow Shafts

Purpose The purpose of this paper is to investigate the use of embedded Shape Memory Alloy (SMA) nitinol wire for the enhancement of vibration and damping characteristics of filament-wound fiber-reinforced plastic composite hollow shafts. Design/methodology/approach The plain Glass Fiber-Reinforced Plastic (GFRP) and plain Carbon Fiber-Reinforced Plastic (CFRP) hollow shafts were manufactured by filament winding technique. Experimental modal analysis was conducted for plain hollow shafts of C1045 steel, GFRP and CFRP by subjecting them to flexural vibrations as per ASTM standard C747, with both ends clamped (C-C) end condition to investigate their vibration and damping behavior in terms of first natural frequency, damping time and damping ratio. Nitinol wires pre-stressed at various pre-strains (2, 4 and 6 per cent) were embedded with CFRP hollow shafts following same manufacturing technique, and similar experimental modal analysis was carried out by activating nitinol wires. The first natural frequencies of all the shaft materials were also predicted theoretically and compared with experimental measurements. Findings Among the three materials C1045 steel, plain GFRP and plain CFRP, the vibration and damping behavior were found to be the best for plain CFRP. Hence, CFRP shafts were considered for further improvement by embedding nitinol wires at pre-stressed condition. For CFRP shafts embedded with nitinol wires, the damping time decreased; and damping ratio and first natural frequency increased with increase in percentage of pre-strain. In comparison with plain CFRP, 7 per cent increase in first natural frequency and 100 per cent increase in damping ratio were observed for nitinol embedded CFRP shafts with 6 per cent pre-strain. Theoretical predictions of the first natural frequencies agree well with the experimental results for all the shaft materials. Originality/value The effect of nitinol on vibration and damping characteristics of filament wound hollow CFRP composite shafts with different pre-strains has not been studied extensively by the previous researchers. This paper addresses the effect of embedded nitinol wires pre-stressed at three varied pre-strains, that is, 2, 4 and 6 per cent on the vibration and damping characteristics of composite hollow CFRP shafts manufactured by filament winding technique.

Design of a Large Diameter Steel Reinforced Plastic Pipe

2011 ◽  
Author(s):  
Jun Shi ◽  
Jing Rao ◽  
Jianfeng Shi ◽  
Ping Xu ◽  
Taiqing Shao ◽  
...  
Keyword(s):  
Structural Parameters ◽  
Steel Wire ◽  
Large Diameter ◽  
Small Diameter ◽  
High Strength ◽  
External Pressure ◽  
Wire Mesh ◽  
Plastic Pipe ◽  
Reinforced Plastic ◽  
Steel Wire Mesh

A steel reinforced plastic pipe (PSP), which is composed of two layers of high density polyethylene (HDPE) matrix and a high strength steel wire mesh skeleton, has wide applications in many industrial areas, such as gas and petroleum transportation, etc. In order to achieve higher efficency and lower costs, a large diameter PSP has been developed. However, requirements of the large diameter PSP in safety and economy are much higher, compared with those small diameter PSPs, and some potential problems should be taken into account. In this paper, relevant structural parameters of the large diameter PSP are determined, based on a previously proposed model, and a short-term burst test is carried out. The experiment results agree with the theoretical results quite well. Subsequently, the resistance of vertical pressure and uniform external pressure are evaluated by using experiment investigation and finite element method, respectively. And corresponding results indicate the large diameter PSP with determined structural parameters is qualified to use.

Sign in / Sign up

Export Citation Format

Share Document