Certain characteristics of fluctuations in arc current and voltage and in the brightness of the jet in eddy-type plasmotrons

1973 ◽  
Vol 11 (5) ◽  
pp. 867-870 ◽  
Author(s):  
A. S. An'shakov ◽  
G. Yu. Dautov ◽  
A. N. Timoshevskii
Keyword(s):  
Arc Current ◽  
Arc Current And Voltage

FIELD STRENGTH IN PULSED MERCURY ARCS

1965 ◽  
Vol 43 (4) ◽  
pp. 670-675 ◽  
Author(s):  
B. Ahlborn ◽  
A. J. Barnard ◽  
H. D. Campbell
Keyword(s):  
Field Strength ◽  
Mercury Vapor ◽  
Average Field ◽  
Arc Plasma ◽  
Cathode Fall ◽  
Arc Current ◽  
Mercury Electrodes ◽  
The Relationship ◽  
Pulsed Arc ◽  
Arc Current And Voltage

In a pulsed arc with mercury electrodes the average column field strength Eco was measured for different currents I, and the relationship [Formula: see text] was found. The variations of arc current and voltage with time indicate that the anode and cathode fall regions have a combined thickness of 3 × 10−6 cm, and an average field strength of 2 × 106 V/cm. The arc plasma is formed mainly from mercury vapor, rather than from the surrounding gas.

scholarly journals Simulation of wire and arc additive manufacturing of 308L stainless steel with cold arc gas metal arc welding

2021 ◽  
Vol 1 (1) ◽  
pp. 88-96
Author(s):  
Nur Izan Syahriah Hussein ◽  
Nur Aisyah Nabilah Mohd Jmmani ◽  
Mohamad Nizam Ayof‬ ◽  
Toibah Abd Rahim ◽  
Muhammad Zaimi Zainal Abidin ◽  
...  
Keyword(s):  
Stainless Steel ◽  
Welding Speed ◽  
Gas Metal Arc Welding ◽  
Base Plate ◽  
Weld Bead ◽  
304L Stainless Steel ◽  
Metal Arc Welding ◽  
Steel Base ◽  
Arc Current ◽  
Arc Current And Voltage

This research focuses on the capabilities of coldArc GMAW in the behavior of heat input to the weld bead dimension. In this study, the effect of process GMAW of 308L stainless steel filler wire with a thickness of 1.2 mm and 304L stainless steel base plate, with a dimension of 120 mm x 25 mm x 10 mm (height x width x thickness) by applying WAAM. The data was collected using MATLAB of a Smart Weld Rosenthal’s Steady-State 3D Isotherms. A Taguchi response was used in the DOE method with Minitab software to analyze the effect of process parameters on height, width, and depth of weld bead dimension during GMAW. The experiments were conducted following the low, mid, and high input parameters will show the different structures of weld bead dimension, which include 70 A, 75 A, and 78 A (arc current), 15 V, 16 V, and 17 V (voltage), 400 mm/min, 600 mm/min, and 800 mm/min (welding speed). Hence, the optimum value is 75 A, 16 V, and 800 mm/min, and the most significant parameters to deposit stainless steel with coldArc GMAW were welding speed followed by arc current and voltage.

Study on the characteristics of secondary arc current of UHV high compensation degree TCSC line under the fine-tuning mode

2021 ◽  
Vol 0 (0) ◽  
Author(s):  
Baina He ◽  
Yadi Xie ◽  
Jingru Zhang ◽  
Nirmal-Kumar C. Nair ◽  
Xingmin He ◽  
...  
Keyword(s):  
Transmission Line ◽  
Transmission Lines ◽  
Stability Margin ◽  
Transmission Capacity ◽  
Fine Tuning ◽  
Series Compensation ◽  
Arc Current ◽  
Compensation Device ◽  
The Stability ◽  
Recovery Voltage

Abstract In the transmission line, the series compensation device is often used to improve the transmission capacity. However, when the fixed series capacitor (FSC) is used in high compensation series compensation device, the stability margin cannot meet the requirements. Therefore, thyristor controlled series compensator (TCSC) is often installed in transmission lines to improve the transmission capacity of the line and the stability of the system. For cost considerations, the hybrid compensation mode of FSC and TCSC is often adopted. However, when a single-phase grounding fault occurs in a transmission line with increased series compensation degree, the unreasonable distribution of FSC and TCSC will lead to the excessive amplitude of secondary arc current, which is not conducive to rapid arc extinguishing. To solve this problem, this paper is based on 1000 kV Changzhi-Nanyang-Jingmen UHV series compensation transmission system, using PSCAD simulation program to established UHV series compensation simulation model, The variation law of secondary arc current and recovery voltage during operation in fine tuning mode after adding TCSC to UHV transmission line is analyzed, and the effect of increasing series compensation degree on secondary arc current and recovery voltage characteristics is studied. And analyze the secondary arc current and recovery voltage when using different FSC and TCSC series compensation degree schemes, and get the most reasonable series compensation configuration scheme. The results show that TCSC compensation is more beneficial to arc extinguishing under the same series compensation. Compared with several series compensation schemes, it is found that with the increase of the proportion of TCSC, the amplitude of secondary arc current and recovery voltage vary greatly. Considering various factors, the scheme that is more conducive to accelerating arc extinguishing is chosen.

Impact of 750kV Transmission Line Series Compensation Capacity on Power Frequency Overvoltage

2014 ◽  
Vol 986-987 ◽  
pp. 330-333
Author(s):  
Ding Jun Wen ◽  
Xiu Bin Zhang ◽  
Hong Gang Chen ◽  
Feng Jiang ◽  
Ya Ming Sun
Keyword(s):  
Transmission Line ◽  
Single Phase ◽  
Power Transmission ◽  
Series Compensation ◽  
Two Phase ◽  
Transient Model ◽  
Power Frequency ◽  
Arc Current ◽  
Recovery Voltage ◽  
Insulation Coordination

The overvoltage calculation of 750kV transmission line with series compensation has great significance on the design, insulation coordination and protection of the line. In this paper, a transient model of 750kV power transmission system with series compensation is established. Effects of different capacity on no-load capacitive rise overvoltage, single-phase grounding overvoltage, two-phase grounding overvoltage are calculated. Secondary arc current and recovery voltage of different series compensation capacity in single-phase grounding is also calculated.

Sign in / Sign up

Export Citation Format

Share Document