Experimental study of sound velocity in some liquid hydrocarbons of the ethylene series within a wide range of pressures and temperatures

1971 ◽  
Vol 14 (8) ◽  
pp. 1153-1155
Author(s):  
A. L. Badalyan ◽  
N. F. Otpushchennikov ◽  
Yu. S. Shoitov
Keyword(s):  
Experimental Study ◽  
Sound Velocity ◽  
Liquid Hydrocarbons ◽  
Wide Range ◽  
Ethylene Series

Experimental Study of Particle Size, Sound Velocity, and Resonance Phenomena in a Two-Phase Foam Flow

2001 ◽  
Vol 32 (4-6) ◽  
pp. 5
Author(s):  
A. P. Sevast'yanov ◽  
I. V. An ◽  
S. I. Vainshtein ◽  
Yu. A. Sevast'yanov ◽  
A. V. Sidnev ◽  
...  
Keyword(s):  
Experimental Study ◽  
Particle Size ◽  
Sound Velocity ◽  
Two Phase ◽  
Foam Flow ◽  
Resonance Phenomena

scholarly journals Improvement of Pump Performance at Off-Design Conditions

1985 ◽  
Author(s):  
J. Paulon ◽  
C. Fradin ◽  
J. Poulain
Keyword(s):  
Experimental Study ◽  
Flow Field ◽  
Mass Flow ◽  
Flow Characteristic ◽  
Three Dimensional ◽  
Operating Conditions ◽  
Pump Performance ◽  
Wide Range ◽  
Mass Flows ◽  
Design Value

Industrial pumps are generally used in a wide range of operating conditions from almost zero mass flow to mass flows larger than the design value. It has been often noted that the head-mass flow characteristic, at constant speed, presents a negative bump as the mass flow is somewhat smaller than the design mass flows. Flow and mechanical instabilities appear, which are unsafe for the facility. An experimental study has been undertaken in order to analyze and if possible to palliate these difficulties. A detailed flow analyzis has shown strong three dimensional effects and flow separations. From this better knowledge of the flow field, a particular device was designed and a strong attenuation of the negative bump was obtained.

scholarly journals Strength Comparison of FDM 3D Printed PLA Made by Different Manufacturers

TEM Journal ◽  
2020 ◽  
pp. 966-970
Author(s):  
Damir Hodžić ◽  
Adi Pandžić ◽  
Ismar Hajro ◽  
Petar Tasić
Keyword(s):  
Experimental Study ◽  
Additive Manufacturing ◽  
Fused Deposition Modelling ◽  
Fused Deposition ◽  
Manufacturing Technique ◽  
Plastic Materials ◽  
Wide Range ◽  
3D Printed ◽  
The Difference ◽  
Printing Parameters

Widely used additive manufacturing technique for plastic materials is Fused Deposition Modelling (FDM). The FDM technology has gained interest in industry for a wide range of applications, especially today when large number of different materials on the market are available. There are many different manufacturers for the same FDM material where the difference in price goes up to 50%. This experimental study investigates possible difference in strength of the 3D printed PLA material of five different manufacturers. All specimens are 3D printed on Ultimaker S5 printer with the same printing parameters, and they are all the same colour.

scholarly journals An experimental study of the dynamics of ascent of the bubble system in the presence of a surfactant

2018 ◽  
Vol 194 ◽  
pp. 01002
Author(s):  
Alexandra Antonnikova ◽  
Sergey Basalaev ◽  
Anna Usanina ◽  
Eugene Maslov
Keyword(s):  
Experimental Study ◽  
Reynolds Numbers ◽  
Experimental Setup ◽  
Bubble Cluster ◽  
Bubble System ◽  
Wide Range ◽  
Compact Cluster ◽  
Glycerol Medium

This paper presents investigations on the new experimental setup for obtaining a compact cluster of monodisperse bubbles of a given diameter is presented. Also we provided the results of experimental study of the bubble cluster floating-up in the presence of a surfactant in a wide range of Reynolds numbers. There was held a comparison of the dynamics of the floating-up of a monodisperse bubble cluster in a glycerol medium and in the medium glycerin supplemented with a surfactant.

scholarly journals Investigation of a promising method for spraying liquid hydrocarbons using the shadow photography method

2019 ◽  
Vol 196 ◽  
pp. 00010 ◽  
Author(s):  
Igor Anufriev ◽  
Evgeniy Shadrin ◽  
Evgeniy Kopyev
Keyword(s):  
High Speed ◽  
Superheated Steam ◽  
Promising Method ◽  
Size Distributions ◽  
Liquid Hydrocarbons ◽  
Droplet Flow ◽  
Fuel Droplets ◽  
Composition And Structure ◽  
Wide Range ◽  
Photography Method

A promising method for spraying liquid hydrocarbons by a high-speed jet of superheated steam was studied experimentally. Information on the disperse composition and structure of the gas-droplet flow during the spraying of used transmission automotive oil was obtained using the method of shadow photography. Size distributions of fuel droplets were obtained in a wide range of operating parameters (flow rate and temperature of steam, fuel consumption).

Experimental Study of Liquid Hydrocarbons Pyrolysis to Acetylene in H2/Ar Plasma

2012 ◽  
Vol 32 (6) ◽  
pp. 1203-1214 ◽  
Author(s):  
Binhang Yan ◽  
Pengcheng Xu ◽  
Xuan Li ◽  
Cliff Yi Guo ◽  
Yong Jin ◽  
...  
Keyword(s):  
Experimental Study ◽  
Liquid Hydrocarbons ◽  
Ar Plasma

Experimental Study of Machining of Smart Materials Using Submerged Abrasive Waterjet Micromachining Process

2018 ◽  
Author(s):  
Sagil James ◽  
Anurag Mahajan
Keyword(s):  
Experimental Study ◽  
Smart Materials ◽  
Thermal Stresses ◽  
Piezoelectric Materials ◽  
High Hardness ◽  
Machining Process ◽  
Critical Parameters ◽  
Abrasive Waterjet ◽  
Parameter Study ◽  
Wide Range

Smart materials are new generation materials which possess great properties to mend themselves with a change in environment. Smart materials find applications in a wide range of industries including biomedical, aerospace, defense and energy sector and so on. These materials possess unique properties including high hardness, high strength, high melting point and low creep behavior. Manufacturing of these materials is a huge challenge, particularly at the micron scale. Abrasive waterjet micromachining (AWJMM) is a non-traditional material removal process which has the capability of machining extremely hard and brittle materials such as glasses and ceramics. AWJMM process is usually performed with nozzle and workpiece placed in air. However, machining in the air causes spreading of the waterjet resulting in low machining quality. Performing the AWJMM process with a submerged nozzle and workpiece could eliminate this problem and also reduce noise, splash, and airborne debris particles during the machining process. This research investigates Submerged Abrasive Waterjet Machining (SAWJMM) process for micromachining smart ceramic materials. The research involves experimental study on micromachining of smart materials using an in-house fabricated SAWJMM setup. The effect of critical parameters including stand-off distance, abrasive grain size and material properties on the cavity size, kerf angle and MRR during SAWJMM and AWJMM processes are studied. The study found that SAWJMM process is capable of successfully machining smart materials including shape memory alloys and piezoelectric materials at the micron scale. The machined surfaced are free of thermal stresses and did not show any cracking around the edges. The critical process parameter study revealed that stand-off distance and abrasive grit size significantly affect the machining results.

Sign in / Sign up

Export Citation Format

Share Document