Effect of particle size on the properties of atomized high-speed steel powders and blanks produced from such powders

1976 ◽  
Vol 15 (5) ◽  
pp. 346-350 ◽  
Author(s):  
A. K. Petrov ◽  
E. N. Smirnova ◽  
I. Ya. Kondratov ◽  
L. V. Ocheretovaya
Keyword(s):  
Particle Size ◽  
High Speed ◽  
High Speed Steel ◽  
Effect Of Particle Size

The Effect of particle size on the burying ability of the brown shrimp Crangon crangon

1993 ◽  
Vol 73 (2) ◽  
pp. 365-377 ◽  
Author(s):  
Eunice H. Pinn ◽  
Alan D. Ansell
Keyword(s):  
Particle Size ◽  
High Speed ◽  
Size Range ◽  
Influencing Factor ◽  
Video Recording ◽  
Crangon Crangon ◽  
Recording Equipment ◽  
High Speed Video ◽  
Naturally Occurring ◽  
Effect Of Particle Size

The burial mechanism of Crangon crangon was examined in detail using high-speed video-recording equipment. Four stages of burial were identified which were associated with three modes of burial. As the mode of burial changed, a change in the angle of substratum penetration was also noted.The effect of particle size on the burying ability of three discrete size classes of shrimp was examined using both artificially graded and naturally occurring sediments. Particle size was found to be a major influencing factor on the degree of burial achieved by C. crangon, but no significant effect of shrimp size on burying ability was found over the size range tested.

Effect of particle size on erosion measurements and predictions in annular flow for an elbow

Wear ◽  
2020 ◽  
pp. 203579
Author(s):  
G. Haider ◽  
M. Othayq ◽  
J. Zhang ◽  
R.E. Vieira ◽  
S.A. Shirazi
Keyword(s):  
Particle Size ◽  
Annular Flow ◽  
Effect Of Particle Size

The Effect of Particle Size and Phospholipid on Growth and Fat Utilization of the Baby Pig

1951 ◽  
Vol 10 (4) ◽  
pp. 867-874 ◽  
Author(s):  
B. E. Sheffy ◽  
Carlos Acevedo Gallegos ◽  
R. H. Grummer ◽  
P. H. Phillips ◽  
G. Bohstedt
Keyword(s):  
Particle Size ◽  
Fat Utilization ◽  
Effect Of Particle Size

Effect of Powder-Mixed Dielectric on EDM Process Performance

2020 ◽  
Vol 38 (8A) ◽  
pp. 1226-1235
Author(s):  
Safa R. Fadhil ◽  
Shukry. H. Aghdeab
Keyword(s):  
Silicon Carbide ◽  
High Speed ◽  
Electrical Discharge Machining ◽  
Removal Rate ◽  
High Speed Steel ◽  
Transformer Oil ◽  
Dielectric Fluid ◽  
Peak Current ◽  
Powder Concentration ◽  
Pulse On Time

Electrical Discharge Machining (EDM) is extensively used to manufacture different conductive materials, including difficult to machine materials with intricate profiles. Powder Mixed Electro-Discharge Machining (PMEDM) is a modern innovation in promoting the capabilities of conventional EDM. In this process, suitable materials in fine powder form are mixed in the dielectric fluid. An equal percentage of graphite and silicon carbide powders have been mixed together with the transformer oil and used as the dielectric media in this work. The aim of this study is to investigate the effect of some process parameters such as peak current, pulse-on time, and powder concentration of machining High-speed steel (HSS)/(M2) on the material removal rate (MRR), tool wear rate (TWR) and the surface roughness (Ra). Experiments have been designed and analyzed using Response Surface Methodology (RSM) approach by adopting a face-centered central composite design (FCCD). It is found that added graphite-silicon carbide mixing powder to the dielectric fluid enhanced the MRR and Ra as well as reduced the TWR at various conditions. Maximum MRR was (0.492 g/min) obtained at a peak current of (24 A), pulse on (100 µs), and powder concentration (10 g/l), minimum TWR was (0.00126 g/min) at (10 A, 100 µs, and 10 g/l), and better Ra was (3.51 µm) at (10 A, 50 µs, and 10 g/l).

Enhancement of EDM Performance by Using Copper-Silver Composite Electrode

2020 ◽  
Vol 38 (9A) ◽  
pp. 1352-1358
Author(s):  
Saad K. Shather ◽  
Abbas A. Ibrahim ◽  
Zainab H. Mohsein ◽  
Omar H. Hassoon
Keyword(s):  
Surface Roughness ◽  
Material Removal Rate ◽  
Material Removal ◽  
High Speed ◽  
Composite Electrode ◽  
Removal Rate ◽  
Pure Copper ◽  
High Speed Steel ◽  
Pulse On Time ◽  
Pulse Off Time

Discharge Machining is a non-traditional machining technique and usually applied for hard metals and complex shapes that difficult to machining in the traditional cutting process. This process depends on different parameters that can affect the material removal rate and surface roughness. The electrode material is one of the important parameters in Electro –Discharge Machining (EDM). In this paper, the experimental work carried out by using a composite material electrode and the workpiece material from a high-speed steel plate. The cutting conditions: current (10 Amps, 12 Amps, 14 Amps), pulse on time (100 µs, 150 µs, 200 µs), pulse off time 25 µs, casting technique has been carried out to prepare the composite electrodes copper-sliver. The experimental results showed that Copper-Sliver (weight ratio70:30) gives better results than commonly electrode copper, Material Removal Rate (MRR) Copper-Sliver composite electrode reach to 0.225 gm/min higher than the pure Copper electrode. The lower value of the tool wear rate achieved with the composite electrode is 0.0001 gm/min. The surface roughness of the workpiece improved with a composite electrode compared with the pure electrode.

Sign in / Sign up

Export Citation Format

Share Document