Effect of electrolyte composition on the properties of electrolytic titanium powders

1987 ◽  
Vol 26 (10) ◽  
pp. 782-785 ◽  
Author(s):  
G. P. Dovgaya ◽  
V. V. Nerubashchenko ◽  
S. P. Chernyshova ◽  
L. K. Mineeva
Keyword(s):  
Electrolyte Composition ◽  
Titanium Powders ◽  
Electrolytic Titanium

Separation and recycling of chloride salts from electrolytic titanium powders by vacuum distillation

2020 ◽  
Vol 236 ◽  
pp. 116282 ◽  
Author(s):  
Liang Li ◽  
Fuxing Zhu ◽  
Pan Deng ◽  
Yaoqiang Jia ◽  
Lingxin Kong ◽  
...  
Keyword(s):  
Vacuum Distillation ◽  
Titanium Powders ◽  
Chloride Salts ◽  
Electrolytic Titanium

Electrolytic Isolation of Twin-Type Shock Deformation Structures

1967 ◽  
Vol 25 ◽  
pp. 318-319
Author(s):  
F. I. Grace ◽  
L. E. Murr
Keyword(s):  
Grain Boundaries ◽  
Thin Foil ◽  
Electrolyte Composition ◽  
Experimental Conditions ◽  
Average Current Density ◽  
Electron Transmission ◽  
Deformation Structures ◽  
The Matrix ◽  
Average Current ◽  
Specimen Edge

During the course of electron transmission investigations of the deformation structures associated with shock-loaded thin foil specimens of 70/30 brass, it was observed that in a number of instances preferential etching occurred along grain boundaries; and that the degree of etching appeared to depend upon the various experimental conditions prevailing during electropolishing. These included the electrolyte composition, the average current density, and the temperature in the vicinity of the specimen. In the specific case of 70/30 brass shock-loaded at pressures in the range 200-400 kilobars, the predominant mode of deformation was observed to be twin-type faults which in several cases exhibited preferential etching similar to that observed along grain boundaries. A novel feature of this particular phenomenon was that in certain cases, especially for twins located in the vicinity of the specimen edge, the etching or preferential electropolishing literally isolated these structures from the matrix.

X-ray fluorescence determination of zinc sulfate in acidic zinc plating electrolyte

2020 ◽  
Vol 86 (10) ◽  
pp. 18-22
Author(s):  
K. N. Vdovin ◽  
K. G. Pivovarova ◽  
N. A. Feoktistov ◽  
T. B. Ponamareva
Keyword(s):  
Zinc Sulfate ◽  
Zinc Coating ◽  
Electrolyte Composition ◽  
Complexometric Titration ◽  
X Ray ◽  
Fluorescence Determination ◽  
Zinc Plating ◽  
Zinc Determination

Zinc sulfate is the main component in the composition of the acidic zinc plating electrolyte. Deviation in the electrolyte composition from the optimum content leads to destabilization of the electrolysis process and deteriorate the quality of the resulting zinc coating. The proper quality of a zinc coating obtained by galvanic deposition can be ensured only with timely monitoring and adjustment of the electrolyte composition. A technique of X-ray fluorescence determination of zinc (in terms of zinc sulfate) in an acidic zinc plating electrolyte is proposed. The study was carried out using an ARL Quant’X energy dispersive spectrometer (Thermo Fisher Scientific, USA) with a semiconductor silicon-lithium detector. The features of the spectrometer design are presented. The optimal parameters of excitation and detection of zinc radiation were specified when the electrolyte sample was diluted 1:1000. The ZnKα1 line was used as an analytical line. The plotted calibration graph is linear, the correlation coefficient being 0.999234. The results of zinc determination according to the developed method were compared with the data of the reference method of complexometric titration to prove the reliability of the procedure. The results are characterized by good convergence and accuracy. The proposed method of X-ray fluorescence zinc determination in a zinc plating electrolyte equals complexometric titration in the limiting capabilities and even exceeds the latter in terms of the simplicity of sample preparation and rapidity. The developed method of X-ray fluorescence determination of zinc is implemented in analysis of the electrolyte used in the continuous galvanizing unit at «METSERVIS LLC».

scholarly journals Spotlight on the Effect of Electrolyte Composition on the Potential of Maximum Entropy. Supporting Electrolytes are not Always Inert

2021 ◽  
Author(s):  
Xing Ding ◽  
Batyr Garlyyev ◽  
Sebastian Watzele ◽  
Theophilus Sarpey ◽  
Aliaksandr Bandarenka
Keyword(s):  
Maximum Entropy ◽  
Electrolyte Composition

Effect of Electrolyte Composition on Corrosion Resistance in Nickel Plating Process for Coating Bonded Magnet PrFeB

2014 ◽  
Vol 896 ◽  
pp. 245-248 ◽  
Author(s):  
Candra Kurniawan ◽  
Hayati M.A. Sholihat ◽  
Kemas Ahmad Zaini Thosin ◽  
Muljadi ◽  
Prijo Sardjono
Keyword(s):  
Magnetic Properties ◽  
Corrosion Resistance ◽  
Corrosion Rate ◽  
Nickel Coating ◽  
Electrolyte Composition ◽  
Nickel Metal ◽  
Sem Images ◽  
Average Value ◽  
Immersion Corrosion ◽  
Bonded Magnet

Despite of its excellence magnetic quality, one of the critical properties of PrFeB based permanent magnet is a low corrosion resistance so it can be oxidized easily which can reduce its magnetic properties. In this study, Nickel coating has been performed for bonded PrFeB magnet by the electroplating method using Nickel-Watts bath-type as the electrolyte to improve the corrosion resistance. The varying amount of the electrolyte compounds used to have the optimized composition indicated by the corrosion resistance measurement. The solution composition used was NiSO4 (230-380 g/L), NiCl2 (30-60 g/L), and H3BO3 (30 and 45 g/L) with a fixed value of other parameters. Characterization used including the immersion corrosion test, microstructure analysis, and magnetic properties. Based on the corrosion rate measurement, the highest corrosion resistant of Nickel coated PrFeB magnet achieved from the electrolyte composition of NiSO4: NiCl2: H3BO3 = 380: 60: 30 g/L with a plating time and current density (J) of 60 minutes and 40 mA/cm2 respectively. The corrosion rate data showed that the Nickel metal coating can improve the corrosion resistance of bonded PrFeB magnet up to 29 times than of the substrate. The SEM images showed that the thickness of the Nickel coating on the optimum electrolyte composition was in average value of 35.1 µm. The overall samples has a magnetic remanence value (Br) reached ≥ 6 kG, so it has enough properties to be applied in devices such as generators and electric motors.

Sign in / Sign up

Export Citation Format

Share Document