Influence of preliminary heat treatment or thermomechanical working on the properties of 51KhFA steel wire after high-temperature thermomechanical working

1988 ◽  
Vol 30 (3) ◽  
pp. 172-176
Author(s):  
V. L. Aleksandrov ◽  
V. N. Konyshev ◽  
Yu. M. Palei ◽  
V. Yu. Zibert ◽  
L. M. Red'kin
Keyword(s):  
Heat Treatment ◽  
High Temperature ◽  
Steel Wire ◽  
Preliminary Heat Treatment ◽  
Thermomechanical Working

High-Temperature Instability of A Cr2Nb-Nb(Cr) Microlaminate Composite

1996 ◽  
Vol 54 ◽  
pp. 374-375
Author(s):  
M. Larsen ◽  
R.G. Rowe ◽  
D.W. Skelly
Keyword(s):  
Heat Treatment ◽  
Solid Solution ◽  
High Temperature ◽  
Elevated Temperatures ◽  
Aircraft Engine ◽  
Lattice Parameter ◽  
Microstructural Stability ◽  
Elevated Temperature Strength ◽  
Cross Sectional ◽  
Bcc Structure

Microlaminate composites consisting of alternating layers of a high temperature intermetallic compound for elevated temperature strength and a ductile refractory metal for toughening may have uses in aircraft engine turbines. Microstructural stability at elevated temperatures is a crucial requirement for these composites. A microlaminate composite consisting of alternating layers of Cr2Nb and Nb(Cr) was produced by vapor phase deposition. The stability of the layers at elevated temperatures was investigated by cross-sectional TEM.The as-deposited composite consists of layers of a Nb(Cr) solid solution with a composition in atomic percent of 91% Nb and 9% Cr. It has a bcc structure with highly elongated grains. Alternating with this Nb(Cr) layer is the Cr2Nb layer. However, this layer has deposited as a fine grain Cr(Nb) solid solution with a metastable bcc structure and a lattice parameter about half way between that of pure Nb and pure Cr. The atomic composition of this layer is 60% Cr and 40% Nb. The interface between the layers in the as-deposited condition appears very flat (figure 1). After a two hour, 1200 °C heat treatment, the metastable Cr(Nb) layer transforms to the Cr2Nb phase with the C15 cubic structure. Grain coarsening occurs in the Nb(Cr) layer and the interface between the layers roughen. The roughening of the interface is a prelude to an instability of the interface at higher heat treatment temperatures with perturbations of the Cr2Nb grains penetrating into the Nb(Cr) layer.

ALTEMP HX

Alloy Digest ◽  
1993 ◽  
Vol 42 (10) ◽  
Keyword(s):  
Heat Treatment ◽  
Solid Solution ◽  
Fracture Toughness ◽  
Corrosion Resistance ◽  
High Temperature ◽  
Base Alloy ◽  
Heat Treating ◽  
Nickel Base Alloy ◽  
Temperature Performance ◽  
Nickel Base

Abstract ALTEMP HX is an austenitic nickel-base alloy designed for outstanding oxidation and strength at high temperatures. The alloy is solid-solution strengthened. Applications include uses in the aerospace, heat treatment and petrochemical markets. This datasheet provides information on composition, physical properties, elasticity, and tensile properties as well as fracture toughness and creep. It also includes information on low and high temperature performance, and corrosion resistance as well as forming, heat treating, and joining. Filing Code: Ni-442. Producer or source: Allegheny Ludlum Corporation.

INCO ALLOY 330

Alloy Digest ◽  
1992 ◽  
Vol 41 (5) ◽  
Keyword(s):  
Heat Treatment ◽  
Solid Solution ◽  
Corrosion Resistance ◽  
High Temperature ◽  
Heat Treating ◽  
High Temperature Alloy ◽  
Nickel Iron ◽  
Temperature Performance ◽  
Inco Alloy ◽  
Iron Chromium

Abstract INCO ALLOY 330 is a nickel/iron/chromium austenitic alloy, not hardenable by heat treatment. It is a solid solution strengthened high-temperature alloy. This datasheet provides information on composition, physical properties, elasticity, and tensile properties as well as creep. It also includes information on high temperature performance and corrosion resistance as well as forming, heat treating, machining, and joining. Filing Code: Ni-403. Producer or source: Inco Alloys International Inc..

ALUMINUM 3004

Alloy Digest ◽  
1974 ◽  
Vol 23 (4) ◽  
Keyword(s):  
Heat Treatment ◽  
Corrosion Resistance ◽  
Shear Strength ◽  
High Temperature ◽  
Magnesium Alloy ◽  
Cold Working ◽  
Heat Treating ◽  
Temperature Performance ◽  
Good Workability ◽  
Manganese Magnesium

Abstract ALUMINUM 3004 is nominally an aluminum-manganese-magnesium alloy which cannot be hardened by heat treatment; however, it can be strain hardened by cold working. It has higher strength than Aluminum 3003 and good workability, weldability and resistance to corrosion. This datasheet provides information on composition, physical properties, hardness, elasticity, tensile properties, and compressive and shear strength as well as fatigue. It also includes information on low and high temperature performance, and corrosion resistance as well as forming, heat treating, machining, and joining. Filing Code: Al-51. Producer or source: Various aluminum companies. Originally published June 1957, revised April 1974.

ALX ALLOY

Alloy Digest ◽  
1963 ◽  
Vol 12 (1) ◽  
Keyword(s):  
Heat Treatment ◽  
Corrosion Resistance ◽  
High Temperature ◽  
Physical Properties ◽  
Tensile Properties ◽  
High Speed ◽  
Heat Treating ◽  
Temperature Performance ◽  
Cobalt Base

Abstract ALX is a composition of nonferrous materials with a cobalt base containing chromium, tungsten and carbon. This alloy is commonly supplied in the cast-to-shape form, having an as-cast hardness of Rockwell C60-62 and requiring no further heat treatment. ALX is also supplied as cast tool bit material and is useful where conventional high-speed steels or carbides do not function effectively. This datasheet provides information on composition, physical properties, hardness, elasticity, and tensile properties. It also includes information on high temperature performance and corrosion resistance as well as casting, forming, heat treating, and machining. Filing Code: Co-35. Producer or source: Allegheny Ludlum Corporation.

ALUMINUM 319.0

Alloy Digest ◽  
1985 ◽  
Vol 34 (5) ◽  
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Shear Strength ◽  
High Temperature ◽  
Physical Properties ◽  
Tensile Properties ◽  
Rear Axle ◽  
Heat Treating ◽  
General Purpose ◽  
Temperature Performance

Abstract ALUMINUM 319.0 is a general-purpose foundry alloy that is moderately responsive to heat treatment. It has excellent casting characteristics and good mechanical properties. Among its many uses are crankcases, housings, engine parts, typewriter frames and rear-axle housings. This datasheet provides information on composition, physical properties, hardness, elasticity, tensile properties, and compressive and shear strength as well as creep and fatigue. It also includes information on low and high temperature performance as well as casting, heat treating, machining, and joining. Filing Code: Al-256. Producer or source: Various aluminum companies.

ALUMINUM 6151

Alloy Digest ◽  
1958 ◽  
Vol 7 (7) ◽  
Keyword(s):  
Heat Treatment ◽  
Shear Strength ◽  
High Temperature ◽  
Physical Properties ◽  
Heat Treating ◽  
Age Hardening ◽  
Temperature Performance ◽  
Aluminum Company ◽  
Aluminum Forging ◽  
Hardening Heat Treatment

Abstract ALUMINUM 6151, formerly A51S Alloy, is an aluminum forging alloy combining good forgeability, strength, and resistance to corrosion. It responds to an age-hardening heat treatment. This datasheet provides information on composition, physical properties, hardness, elasticity, tensile properties, and shear strength as well as fatigue. It also includes information on high temperature performance as well as forming, heat treating, machining, and joining. Filing Code: Al-67. Producer or source: Aluminum Company of America.

Sign in / Sign up

Export Citation Format

Share Document