Carbide heterogeneity of hydrostatically extruded blanks for shaping tools

1976 ◽  
Vol 18 (5) ◽  
pp. 420-422
Author(s):  
Yu. F. Chernyi ◽  
V. S. Koviko ◽  
G. A. Dotsenko
Keyword(s):  
Carbide Heterogeneity

Study of factors contributing to decrease of carbide heterogeneity in bearing grades of steel

2021 ◽  
Vol 77 (7) ◽  
pp. 804-810
Author(s):  
I. A. Pankovets ◽  
S. A. Savchenko ◽  
V. I. Voznaya ◽  
M. N. Vereshchagin ◽  
I. V. Astapenko
Keyword(s):  
Bearing Steel ◽  
Rolled Stock ◽  
Carbide Network ◽  
Bearing Steels ◽  
Mill Equipment ◽  
Long Time ◽  
Steel Grades ◽  
Rolling Production ◽  
And Control ◽  
Carbide Heterogeneity

At present to meet requirement to the quality of bearing steels it is necessary of accomplish estimation of carbide heterogeneity by SEP 1520 and provide the level of carbide network, carbide liquation and streaking, not exceeding adjusted limits, required by customer. To estimate possibility to decrease carbide heterogeneity (segregation), factors influencing its value in the rolling production considered. Description of the process of long products of bearing steels production at the rolling mill 370/150 of the OJSC “BMZ - managing company of the holding “BMK” presented. Possibilities of the existing mill equipment considered for 804 accomplishing of technological operations aimed at decrease of carbide heterogeneity in the finished product. The factors studied, contributing to decrease of carbide heterogeneity under conditions of mill 370/150 operation. To determine the temperature modes effect on the level of carbide heterogeneity in bearing steels, in the process of three campaigns phased decrease of the temperature of end of rolling was accomplished. Results of data analysis obtained at the production of long products profiles of 34-50 diameter of bearing steel grades presented. Conclusion on rolled stock production of bearing steel grades with high requirements to carbide heterogeneity value was formed. It was shown that to obtain high-quality long products it is appropriate to accomplish the heating in the furnace before the rolling no less than 600 min at the temperature in the soaking zone 1150-1220°С followed by application of tech­nology of normalizing rolling and control of temperature of the end of rolling 750°С. For profiles with drawing less 25% it is rec­ommended to accomplish additional heat treatment of the finished profile - normalization. Long time heating of workpieces before the rolling at the temperature 1150-1220°С enables to decrease the carbide heterogeneity down to acceptable level (carbide liquation no more than 3 points and carbide streaking no more than 4 points). The value of carbide network is decreasing at decreasing of tem­perature of the end of the rolling and increasing deformation value in the last stands. A stable satisfactory result (CN no more than 5.4) was reached at the temperature of the end of rolling 750°С and drawing more than 25%. It was established that the higher the total drawing, the lower the point of carbide network and liquation in the finished profile, which is caused by crushing of nondissolved carbides to separate fragments.

Change in carbide heterogeneity during hot extrusion of cutting tools for high-speed steels

1978 ◽  
Vol 20 (9) ◽  
pp. 742-746
Author(s):  
�. O. Maizel's ◽  
V. G. Kantin ◽  
I. K. Danil'chik
Keyword(s):  
High Speed ◽  
Cutting Tools ◽  
Hot Extrusion ◽  
Carbide Heterogeneity

scholarly journals Improvement of the technological process of manufacturing bearing grades of steel at the 370/150 mill.

2021 ◽  
pp. 65-73
Author(s):  
V. S. Puteev ◽  
S. A. Savchenko ◽  
I. A. Pankovets ◽  
V. I. Voznaja ◽  
I. V. Astapenko
Keyword(s):  
Bearing Steel ◽  
Steel Grade ◽  
Cast Billet ◽  
Microstructure Characteristics ◽  
Continuously Cast Billet ◽  
Steel Grades ◽  
Continuously Cast ◽  
Thermal Preparation ◽  
Technical Measures ◽  
Carbide Heterogeneity

The actual problem of obtaining long products from bearing steel grades with specified microstructure characteristics is considered. The analysis of the capabilities of the existing equipment – a heating furnace and a rolling mill 370/150 of OJSC “BSW – Management Company of the Holding “BMC” was carried out in order to introduce technical measures aimed at reducing carbide heterogeneity in products made of bearing steel grades on the example of steel grade 100Cr6.The influence of different modes of preliminary thermal preparation of continuously cast billets from bearing steel grades on the carbide inhomogeneity in the finished rolling is studied. According to the results of the research, the optimal mode of heat treatment of a continuously cast billet was determined, which allows to produce rolled products that meet the highest requirements of consumers.

Sign in / Sign up

Export Citation Format

Share Document