Effect of thermal stresses and phase transformations on the strength of Ticonal alloy

1978 ◽  
Vol 20 (6) ◽  
pp. 504-507
Author(s):  
G. P. Vasin ◽  
V. N. Soplyachenko ◽  
N. F. Kartashova
Keyword(s):  
Phase Transformations ◽  
Thermal Stresses ◽  
Ticonal Alloy

NUMERICAL MODELING OF PHASE TRANSFORMATION DURING GRINDING PROCESS

2017 ◽  
Vol 79 (5) ◽  
Author(s):  
Syed Mushtaq Ahmed Shah ◽  
M. A. Khattak ◽  
Muhammad Asad ◽  
Javed Iqbal ◽  
Saeed Badshah ◽  
...  
Keyword(s):  
Phase Transformation ◽  
Phase Transformations ◽  
Thermal Stresses ◽  
Heating Temperature ◽  
Temperature History ◽  
Grinding Process ◽  
Cooling Rates ◽  
Continuous Cooling Transformation ◽  
Continuous Cooling ◽  
Heating And Cooling

The rapid heating and cooling in a grinding process may cause phase transformations. This will introduce thermal strains and plastic strains simultaneously in a workpiece with substantial residual stresses. The properties of the workpiece material will change when phase transformation occurs. The extent of such change depends on the temperature history experienced and the instantaneous thermal stresses developed. To carry out a reliable residual stress analysis, a comprehensive modelling technique and a sophisticated computational procedure that can accommodate the property change with the metallurgical change of material need to be developed. The objective of this work is to propose a simplified model to predict phase evolution during given temperature history for heating and cooling as encountered during grinding process. The numerical implementation of the proposed model is carried out through the developed FORTRAN subroutine called PHASE using the FEM commercial software Abaqus®/standard. Micro-structural constituents are defined as state variables. They are computed and updated inside the subroutine PHASE. The heating temperature is assumed to be uniform while the cooling characteristics in relation to phase transformations are obtained from the continuous cooling transformation (CCT) diagram of the given material (here AISI 52100 steel). Four metallurgical phases are assumed for the simulations: austenite, pearlite, bainite, and martensite. It was shown that at low cooling rates high percentage of pearlite phase is obtained when the material is heated and cooled to ambient temperature. Bainite is formed usually at medium cooling rates. Similarly at high cooling rates maximum content of martensite may be observed. It is also shown that the continuous cooling transformation kinetics may be described by plotting the transformation temperature, directly against the cooling rate as an alternative to the continuous cooling transformation diagram. The simulated results are also compared with experimental results of Wever [20] and Hunkle [21] and are found to be in a very good agreement. The model may be used for further thermo-mechanical analysis coupled with phase transformation during grinding process.

Deformation at interfaces of Ti-6Al-4V/SiC fiber composites

1992 ◽  
Vol 50 (1) ◽  
pp. 158-159
Author(s):  
Warren J. Moberly ◽  
Daniel B. Miracle ◽  
S. Krishnamurthy
Keyword(s):  
Thermal Stresses ◽  
Load Transfer ◽  
Coefficient Of Thermal Expansion ◽  
Hot Isostatic Pressing ◽  
Matrix Composites ◽  
Ongoing Research ◽  
Aerospace Applications ◽  
Sic Fiber ◽  
The Matrix ◽  
Intermetallic Matrix Composites

Titanium-aluminum alloy metal matrix composites (MMC) and Ti-Al intermetallic matrix composites (IMC), reinforced with continuous SCS6 SiC fibers are leading candidates for high temperature aerospace applications such as the National Aerospace Plane (NASP). The nature of deformation at fiber / matrix interfaces is characterized in this ongoing research. One major concern is the mismatch in coefficient of thermal expansion (CTE) between the Ti-based matrix and the SiC fiber. This can lead to thermal stresses upon cooling down from the temperature incurred during hot isostatic pressing (HIP), which are sufficient to cause yielding in the matrix, and/or lead to fatigue from the thermal cycling that will be incurred during application, A second concern is the load transfer, from fiber to matrix, that is required if/when fiber fracture occurs. In both cases the stresses in the matrix are most severe at the interlace.

The use of high-resolution FESEM to study solid-state phase transformations and reactions

1994 ◽  
Vol 52 ◽  
pp. 1028-1029
Author(s):  
P. G. Kotula ◽  
D. D. Erickson ◽  
C. B. Carter
Keyword(s):  
Solid State ◽  
High Resolution ◽  
Phase Transformations ◽  
High Efficiency ◽  
Sol Gel ◽  
Quantitative Information ◽  
Solid State Reactions ◽  
Critical Dimensions ◽  
Backscattered Electrons ◽  
Backscattered Electron

High-resolution field-emission-gun scanning electron microscopy (FESEM) has recently emerged as an extremely powerful method for characterizing the micro- or nanostructure of materials. The development of high efficiency backscattered-electron detectors has increased the resolution attainable with backscattered-electrons to almost that attainable with secondary-electrons. This increased resolution allows backscattered-electron imaging to be utilized to study materials once possible only by TEM. In addition to providing quantitative information, such as critical dimensions, SEM is more statistically representative. That is, the amount of material that can be sampled with SEM for a given measurement is many orders of magnitude greater than that with TEM.In the present work, a Hitachi S-900 FESEM (operating at 5kV) equipped with a high-resolution backscattered electron detector, has been used to study the α-Fe2O3 enhanced or seeded solid-state phase transformations of sol-gel alumina and solid-state reactions in the NiO/α-Al2O3 system. In both cases, a thin-film cross-section approach has been developed to facilitate the investigation. Specifically, the FESEM allows transformed- or reaction-layer thicknesses along interfaces that are millimeters in length to be measured with a resolution of better than 10nm.

The use of transmission and analytical electron microscopy in studying reactions and phase transformations in thin film

1993 ◽  
Vol 51 ◽  
pp. 842-843
Author(s):  
K. Barmak
Keyword(s):  
Thin Film ◽  
Thin Films ◽  
Phase Transformations ◽  
Analytical Electron Microscopy ◽  
Ex Situ ◽  
Multilayer Thin Films ◽  
Absolute Concentration ◽  
Analytical Electron ◽  
Deposition Step

Generally, processing of thin films involves several annealing steps in addition to the deposition step. During the annealing steps, diffusion, transformations and reactions take place. In this paper, examples of the use of TEM and AEM for ex situ and in situ studies of reactions and phase transformations in thin films will be presented.The ex situ studies were carried out on Nb/Al multilayer thin films annealed to different stages of reaction. Figure 1 shows a multilayer with dNb = 383 and dAl = 117 nm annealed at 750°C for 4 hours. As can be seen in the micrograph, there are four phases, Nb/Nb3-xAl/Nb2-xAl/NbAl3, present in the film at this stage of the reaction. The composition of each of the four regions marked 1-4 was obtained by EDX analysis. The absolute concentration in each region could not be determined due to the lack of thickness and geometry parameters that were required to make the necessary absorption and fluorescence corrections.

A Transmission Electron Microscopical Investigation of Phase Transformations in TiNi

1980 ◽  
Vol 38 ◽  
pp. 340-341
Author(s):  
P. Moine ◽  
G. M. Michal ◽  
R. Sinclair
Keyword(s):  
Electron Microscopy ◽  
Phase Transformations ◽  
Applied Stress ◽  
Structural Changes ◽  
Microscopical Investigation ◽  
Temperature Range ◽  
Transmission Electron ◽  
Electron Microscopical ◽  
Diffraction Effects ◽  
Microscopy Images

Premartensitic effects in near equiatomic TiNi have been pointed out by several authors(1-5). These include anomalous contrast in electron microscopy images (mottling, striations, etc. ),diffraction effects(diffuse streaks, extra reflections, etc.), a resistivity peak above Ms (temperature at which a perceptible amount of martensite is formed without applied stress). However the structural changes occuring in this temperature range are not well understood. The purpose of this study is to clarify these phenomena.

Sign in / Sign up

Export Citation Format

Share Document