Method for evaluating the crack resistance of small sized metallic materials

1993 ◽  
Vol 25 (6) ◽  
pp. 417-424
Author(s):  
V. A. Rakovskii ◽  
V. P. Naumenko ◽  
V. I. Prokhorov ◽  
A. V. Golubenko
Keyword(s):  
Crack Resistance ◽  
Metallic Materials

Modeling of the ductile-brittle transition in porous metallic materials under conditions of crack resistance tests

1990 ◽  
Vol 29 (5) ◽  
pp. 411-416 ◽  
Author(s):  
S. A. Firstov ◽  
Yu. N. Podrezov ◽  
L. G. Shtyka ◽  
A. G. Zherdin ◽  
A. A. Malyshenko
Keyword(s):  
Crack Resistance ◽  
Metallic Materials ◽  
Brittle Transition ◽  
Resistance Tests

SEM Examination of a Used Diamond Knife

1971 ◽  
Vol 29 ◽  
pp. 452-453
Author(s):  
J. Temple Black
Keyword(s):  
Electron Microscope ◽  
High Voltage ◽  
High Magnification ◽  
Metallic Materials ◽  
Wide Spread ◽  
Thin Sections ◽  
Transmission Electron ◽  
Scanning Transmission ◽  
Scanning Electron ◽  
Diamond Knife

Since its introduction by Fernandez-Moran, the diamond knife has gained wide spread usage as a common material for cutting of thin sections of biological and metallic materials into thin films for examination in the transmission electron microscope. With the development of high voltage E.M. and scanning transmission E.M., microtomy applications will become increasingly important in the preparation of specimens. For those who can afford it, the diamond knife will thus continue to be an important tool to accomplish this effort until a cheaper but equally strong and sharp tool is found to replace the diamond, glass not withstanding.In Figs. 1 thru 3, a first attempt was made to examine the edge of a used (β=45°) diamond knife by means of the scanning electron microscope. Because diamond is conductive, first examination was tried without any coating of the diamond. However, the contamination at the edge caused severe charging during imaging. Next, a thin layer of carbon was deposited but charging was still extensive at high magnification - high voltage settings. Finally, the knife was given a light coating of gold-palladium which eliminated the charging and allowed high magnification micrographs to be made with reasonable resolution.

Observation of secondary slip systems in tungsten bicrystals

1984 ◽  
Vol 42 ◽  
pp. 478-479
Author(s):  
J. R. Fekete ◽  
R. Gibala
Keyword(s):  
Stress Field ◽  
Grain Boundaries ◽  
Deformation Behavior ◽  
Stress Axis ◽  
Polycrystalline Materials ◽  
Slip Systems ◽  
Metallic Materials ◽  
Twist Boundary ◽  
Secondary Slip ◽  
Plane Normal

The deformation behavior of metallic materials is modified by the presence of grain boundaries. When polycrystalline materials are deformed, additional stresses over and above those externally imposed on the material are induced. These stresses result from the constraint of the grain boundaries on the deformation of incompatible grains. This incompatibility can be elastic or plastic in nature. One of the mechanisms by which these stresses can be relieved is the activation of secondary slip systems. Secondary slip systems have been shown to relieve elastic and plastic compatibility stresses. The deformation of tungsten bicrystals is interesting, due to the elastic isotropy of the material, which implies that the entire compatibility stress field will exist due to plastic incompatibility. The work described here shows TEM observations of the activation of secondary slip in tungsten bicrystals with a [110] twist boundary oriented with the plane normal parallel to the stress axis.

Microstructural aspects of spalling for hard metallic materials

2000 ◽  
Vol 10 (PR9) ◽  
pp. Pr9-641-Pr9-646
Author(s):  
P. Chevrier ◽  
J. R. Klepaczko
Keyword(s):  
Metallic Materials

Effect of Plastic Deformation on Hydrogen Induced Crack Resistance of API X65 Linepipe Steel

2016 ◽  
Vol 54 (4) ◽  
pp. 295-303 ◽  
Author(s):  
Kyung-Mox Cho ◽  
Joon-Ho Sung ◽  
Yun-Kyu Kim ◽  
Jong-Geol Moon ◽  
Ki-Won Kim ◽  
...  
Keyword(s):  
Plastic Deformation ◽  
Crack Resistance ◽  
Linepipe Steel
Sign in / Sign up

Export Citation Format

Share Document