Steel production with vacuum degassing and treatment in a slag column

Metallurgist ◽  
1983 ◽  
Vol 27 (9) ◽  
pp. 300-301
Author(s):  
I. D. Lysenko ◽  
A. N. Samsonov ◽  
E. I. Moshkevich ◽  
V. P. Denisenko ◽  
V. M. Kulik ◽  
...  
Keyword(s):  
Steel Production ◽  
Vacuum Degassing ◽  
Slag Column

The microstructure change of low-carbon electrical steels by residual aluminum

1989 ◽  
Vol 47 ◽  
pp. 286-287
Author(s):  
C.K. Hou ◽  
C.T. Hu ◽  
Sanboh Lee
Keyword(s):  
Annealing Treatment ◽  
Low Carbon ◽  
Electrical Steels ◽  
Vacuum Degassing ◽  
Spherical Inclusions ◽  
Residual Aluminum ◽  
Average Grain Size ◽  
The Matrix ◽  
Fine Size ◽  
To Come

The fully processed low-carbon electrical steels are generally fabricated through vacuum degassing to reduce the carbon level and to avoid the need for any further decarburization annealing treatment. This investigation was conducted on eighteen heats of such steels with aluminum content ranging from 0.001% to 0.011% which was believed to come from the addition of ferroalloys.The sizes of all the observed grains are less than 24 μm, and gradually decrease as the content of aluminum is increased from 0.001% to 0.007%. For steels with residual aluminum greater than 0. 007%, the average grain size becomes constant and is about 8.8 μm as shown in Fig. 1. When the aluminum is increased, the observed grains are changed from the uniformly coarse and equiaxial shape to the fine size in the region near surfaces and the elongated shape in the central region. SEM and EDAX analysis of large spherical inclusions in the matrix indicate that silicate is the majority compound when the aluminum propotion is less than 0.003%, then the content of aluminum in compound inclusion increases with that in steel.

Drying and heating of scrap metal at steelmaking: industrial safety, economics, ecology

2020 ◽  
Vol 76 (12) ◽  
pp. 1353-1258
Author(s):  
V. A. Spirin ◽  
V. E. Nikol’skii ◽  
D. V. Vokhmintsev ◽  
A. A. Moiseev ◽  
P. G. Smirnov ◽  
...  
Keyword(s):  
Energy Efficiency ◽  
High Efficiency ◽  
Steel Production ◽  
Scrap Metal ◽  
Industrial Safety ◽  
Technical Solution ◽  
Metal Charge ◽  
Basic Task ◽  
Scrap Heating ◽  
Winter Time

At steel production based on scrap metal utilization, the scrap heating before charging into a melting facility is an important way of energy efficiency increase and ecological parameters improving. In winter time scrap metal charging with ice inclusions into a metal melt can result in a considerable damage of equipment and even accidents. Therefore, scrap preliminary drying is necessary to provide industrial safety. It was shown, that in countries with warm and low-snow climate with no risk of scrap metal icing up during its transportation and storing in the open air, the basic task being solved at the scrap drying is an increase of energy efficiency of steelmaking. InRussiathe scrap metal drying first of all provides the safety of the process and next - energy saving. Existing technologies of scrap metal drying and heating considered, as well as advantages and drawbacks of technical solutions used at Russian steel plants. In winter time during scrap metal heating at conveyers (Consteel process) hot gases penetrate not effectively into its mass, the heat is not enough for evaporation of wetness in the metal charge. At scrap heating by the furnace gases, a problem of dioxines emissions elimination arises. Application of shaft heaters results in high efficiency of scrap heating. However, under conditions of Russian winter the upper scrap layers are not always heated higher 0 °С and after getting into a furnace bath the upper scrap layers cause periodical vapor explosions. The shaft heaters create optimal conditions for dioxines formation, which emit into atmosphere. It was shown, that accounting Russian economic and nature conditions, the metal charge drying and heating in modified charging buckets by the heat of burnt natural gas or other additional fuel is optimal. The proposed technical solution enables to burnt off organic impurities ecologically safely, to melt down ice, to evaporate the wetness in the scrap as well as to heat the charge as enough as the charging logistics enables it. The method was implemented at several Russian steel plants. Technical and economical indices of scrap metal drying in buckets under conditions of EAF-based shop, containing two furnaces ДСП-100, presented.

Factors Affecting the Decision to Apply Material Flows Cost Accounting MFCA in Thai Nguyen Steel Production Enterprises

2020 ◽  
Vol 36 (3) ◽  
Author(s):  
Nguyen Thi Kim Huyen
Keyword(s):  
Production Process ◽  
Environmental Performance ◽  
Steel Production ◽  
Cost Accounting ◽  
Environmental Accounting ◽  
Production Costs ◽  
Accounting System ◽  
Material Flows ◽  
Factors Affecting ◽  
Legal Documents

Applying the Material Flows Cost Accounting method in Thai Nguyen steel enterprises is one of the solutions to improve the efficiency in the production process, using input materials, and environmental performance, as well as to measure more correctly the production costs based on the change of the price calculation basic. Identifying the factors which affect the decision on applying MFCA to the accounting process of Thai Nguyen steel production enterprises by a direct survey is carried out with 119 accountants and managers working at 13 steel enterprises. The results show that applying MFCA to the accounting process in these enterprises depends on the strategies, capacities, the accounting system of those enterprises, and the system of legal documents related to environmental accounting.

LUKENS HARDWEAR 500F

Alloy Digest ◽  
1994 ◽  
Vol 43 (6) ◽  
Keyword(s):  
Wear Resistance ◽  
Tensile Properties ◽  
Production Technology ◽  
Steel Production ◽  
Carbon Equivalent ◽  
Steel Company ◽  
Armor Steel

Abstract LUKENS HARDWEAR 500F steel was developed from armor steel production technology to have as low a carbon equivalent as possible, consistent with meeting both surface and through-thickness hardness. Uses include truck body liners, bucket lips and conveyor troughs. This datasheet provides information on composition, hardness, and tensile properties. It also includes information on wear resistance as well as forming and joining. Filing Code: SA-476. Producer or source: Lukens Steel Company.

Sign in / Sign up

Export Citation Format

Share Document