Development of the superplasticity effect in aluminum alloys with lithium

1985 ◽  
Vol 27 (2) ◽  
pp. 165-166
Author(s):  
I. N. Fridlyander ◽  
E. V. �khina ◽  
T. M. Kunyavskaya ◽  
V. L. Likin
Keyword(s):  
Aluminum Alloys ◽  
Superplasticity Effect

Superplasticity Effect Demonstrated by Gas Forming Hot Bent AA5XXX Sheets into V-Shaped Trough Containing Uneven Concavities

2016 ◽  
Vol 838-839 ◽  
pp. 592-596
Author(s):  
Chia Hung Chen ◽  
Jian Yih Wang ◽  
Yiin Kuen Fuh ◽  
Shyong Lee ◽  
Chi Liu ◽  
...  
Keyword(s):  
Aluminum Alloys ◽  
Strain Rate ◽  
Gas Pressure ◽  
Superplastic Material ◽  
Flow Properties ◽  
Metal Sheets ◽  
Processing History ◽  
Key Factor ◽  
Product Standard ◽  
Superplasticity Effect

Using low gas pressure as a tool to form metal sheets is certainly feasible. However, the intrinsic flow properties of metal sheet are often a key factor in determining degree of formability, which has not been emphasized or explained well. Most metals, for examples aluminum alloys, can be either superplastic or non-superplastic depending on their original processing history or route (consequently, yielding suitable microstructure) and forming conditions, i.e. mostly temperature and strain rate. This superplasticity effect is clearly demonstrated by gas forming superplastic AA5083 and non-superplastic AA5052 into a V-shaped deep trough containing uneven concavities. The results show the superiority of superplastic material when harsh product standard is required.

Analytical Electron Microscopy Study of Second-Phase Particles in 7075 and 7475 Aluminum Alloys

1985 ◽  
Vol 43 ◽  
pp. 348-349
Author(s):  
M. Raghavan ◽  
J. Y. Koo ◽  
J. W. Steeds ◽  
B. K. Park
Keyword(s):  
Aluminum Alloys ◽  
Silicon Oxide ◽  
Analytical Electron Microscopy ◽  
Microscopy Study ◽  
Electron Microscopy Study ◽  
Partial Substitution ◽  
Second Phase ◽  
X Ray ◽  
Second Phase Particles ◽  
Almost All

X-ray microanalysis and Convergent Beam Electron Diffraction (CBD) studies were conducted to characterize the second phase particles in two commercial aluminum alloys -- 7075 and 7475. The second phase particles studied were large (approximately 2-5μm) constituent phases and relatively fine ( ∼ 0.05-1μn) dispersoid particles, Figures 1A and B. Based on the crystal structure and chemical composition analyses, the constituent phases found in these alloys were identified to be Al7Cu2Fe, (Al,Cu)6(Fe,Cu), α-Al12Fe3Si, Mg2Si, amorphous silicon oxide and the modified 6Fe compounds, in decreasing order of abundance. The results of quantitative X-ray microanalysis of all the constituent phases are listed in Table I. The data show that, in almost all the phases, partial substitution of alloying elements occurred resulting in small deviations from the published stoichiometric compositions of the binary and ternary compounds.

Electrochemical Impedance Characteristics of Sintered 7075 Aluminum Alloy Under Ssrt Condition

2013 ◽  
Vol 58 (2) ◽  
pp. 505-508 ◽  
Author(s):  
S. Sunada ◽  
N. Nunomura
Keyword(s):  
Aluminum Alloys ◽  
Complex Shape ◽  
Electrochemical Impedance ◽  
Ingot Metallurgy ◽  
View Point ◽  
Corrosion Properties ◽  
Electrochemical Tests ◽  
Impedance Characteristics ◽  
Polarization Test ◽  
Conventional Ingot

Powder metallurgy (P/M) process has the advantage of better formability to fabricate complex shape products without machining and welding. And recently this P/M process has been applied to the production of aluminum alloys. The P/M aluminum alloys thus produced also have received considerable interest because of their fine and homogeneous structure. Many papers have been published on the mechanical properties of the aluminum alloys produced by P/M process while there have been few on their corrosion properties from the view point of electrochemistry. In this experiment, therefore, two kinds of 7075 aluminum alloys prepared by the conventional ingot metallurgy (I/M) process and P/M process were used, I/M material is commercially available. and their corrosion behavior were investigated through the electrochemical tests such as potentiodynamic polarization test, slow rate strain tensile (SSRT) test and electrochemical impedance spectroscopy (EIS) measurement under SSRT test in the corrosion solution and the deionized water.

Sign in / Sign up

Export Citation Format

Share Document