Combustion synthesis of niobium aluminide and its mechanical properties

1992 ◽  
Vol 11 (8) ◽  
pp. 475-476 ◽  
Author(s):  
A. K. Bhattacharya ◽  
C. T. Ho ◽  
J. A. Sekhar
Keyword(s):  
Mechanical Properties ◽  
Combustion Synthesis ◽  
Niobium Aluminide

Simultaneous Synthesis and Consolidation of Nanostructured ZrB2–ZrO2 Composite

2020 ◽  
Vol 20 (7) ◽  
pp. 4349-4352
Author(s):  
Seong-Eun Kim ◽  
Jin-Kook Yoon ◽  
In-Jin Shon
Keyword(s):  
Mechanical Properties ◽  
Combustion Synthesis ◽  
High Frequency ◽  
Combined Effects ◽  
Induced Current ◽  
Mechanical Pressure ◽  
Simultaneous Application ◽  
Average Grain Size ◽  
One Step ◽  
Simultaneous Synthesis

A dense nanostructured 2ZrB2–ZrO2 composite was synthesized by the high-frequency inductionheated combustion synthesis (HFIHCS) method within 2 min in one step from mechanically activated powders of 2B2O3 and 3Zr. Simultaneous combustion synthesis and densification were accomplished under the combined effects of the induced current and mechanical pressure. A highly dense 2ZrB2–ZrO2 composite with relative density of up to 95.5% was produced under the simultaneous application of a pressure of 80 MPa and the induced current. The average grain size and mechanical properties (hardness and fracture toughness) of the composite were investigated.

Fabrication of MgO/Graphene Composites by Combustion Synthesis and Spark Plasma Sintering

2018 ◽  
Vol 281 ◽  
pp. 125-130
Author(s):  
Nan Lu ◽  
Jia Xi Liu ◽  
Gang He ◽  
Jiang Tao Li
Keyword(s):  
Mechanical Properties ◽  
Combustion Synthesis ◽  
Spark Plasma Sintering ◽  
Sintering Temperature ◽  
Ceramic Composites ◽  
Combustion Reaction ◽  
Sintering Additive ◽  
Microstructure And Mechanical Properties ◽  
Plasma Sintering ◽  
Spark Plasma

MgO/Graphene ceramic composites were fabricated by combining combustion synthesis with spark plasma sintering. MgO/Graphene mixture powders were prepared by the combustion reaction between Mg powders and CO2 gas. Dense MgO/Graphene composites were fabricated by spark plasma sintering (SPS) using LiF as the sintering additive. The effect of the sintering temperature on microstructure and mechanical properties of the prepared MgO/Graphene ceramics was discussed. The sintering temperature of the MgO/Graphene mixture powders increased from 900°C to 1300°C. The highest density of 3.43g/cm3 and hardness of 2133MPa were obtained at 1100°C. Compared with monolithic MgO ceramics, the hardness of MgO/Graphene ceramics at the same sintering temperature was increased from 840MPa to 2133MPa.

Combustion Synthesis of Alumina-Based Multiphase Foam Ceramic

2008 ◽  
Vol 368-372 ◽  
pp. 1526-1528 ◽  
Author(s):  
Jun Shou Li ◽  
Liang Li ◽  
Jian Jiang Wang ◽  
Bing She Xu ◽  
Yu Jun Yin
Keyword(s):  
Mechanical Properties ◽  
High Temperature ◽  
Combustion Synthesis ◽  
Influencing Factors ◽  
Direct Observation ◽  
Compression Strength ◽  
Pore Diameter ◽  
Foaming Agent ◽  
Temperature Resistance ◽  
Foam Ceramic

Al2O3-TiO-TiO2 multiphase foam ceramic was prepared with Al powders and TiO2 powders by combustion synthesis, Direct observation and metallographic microscope indicated that the pore diameter is 100~6000μm, and Archimedean method showed that the porosity is 35~50%. The influencing factors of the pore diameter and porosity and, the effects of adding SiO2 on compression strength of the Al2O3- TiO-TiO2 multiphase foam ceramic were discussed. It was shown that the addition of proper high temperature foaming agent can increase porosity and adding SiO2 can decrease porosity. The Al2O3-TiO-TiO2 multiphase foam ceramic has good mechanical properties and high-temperature resistance.

Combustion Synthesis of Niobium Aluminide Matrix Composites

1994 ◽  
Vol 350 ◽  
Author(s):  
C. R. Kachelmyer ◽  
A. Varma
Keyword(s):  
Melting Point ◽  
Combustion Synthesis ◽  
Thermal Explosion ◽  
Matrix Composites ◽  
Product Density ◽  
B Additions ◽  
Reaction Completion ◽  
Niobium Aluminide

AbstractCombustion synthesis of NbAl3-matrix composites with Al2O3 and B additions was studied using the thermal explosion mode. The addition of B to the reaction mixture resulted in the formation of NbB2, small amounts of NbB and unreacted Al. The Al2O3 addition did not affect the NbAl3-matrix reaction completion but the final product density increased with increasing Al2O3 loading. In both NbAl3-matrix composites, the reaction was initiated above the melting point of Al.

Sign in / Sign up

Export Citation Format

Share Document