Influence of cooling rate and soap concentration on isothermal crystallization temperature of lithium greases

1987 ◽  
Vol 23 (2) ◽  
pp. 79-81 ◽  
Author(s):  
L. V. Podlennykh ◽  
L. P. Ishchuk
Keyword(s):  
Cooling Rate ◽  
Crystallization Temperature ◽  
Isothermal Crystallization ◽  
Soap Concentration

scholarly journals Non-Isothermal Crystallization Kinetics of Poly(4-Hydroxybutyrate) Biopolymer

Molecules ◽  
2019 ◽  
Vol 24 (15) ◽  
pp. 2840 ◽  
Author(s):  
Ina Keridou ◽  
Luis J. del Valle ◽  
Lutz Funk ◽  
Pau Turon ◽  
Lourdes Franco ◽  
...  
Keyword(s):  
Growth Rate ◽  
Cooling Rate ◽  
Crystallization Temperature ◽  
Isothermal Crystallization ◽  
Secondary Nucleation ◽  
Scanning Calorimetry ◽  
Limited Region ◽  
First Case ◽  
Biodegradable Poly ◽  
Insertion Mechanism

The non-isothermal crystallization of the biodegradable poly(4-hydroxybutyrate) (P4HB) has been studied by means of differential scanning calorimetry (DSC) and polarizing optical microscopy (POM). In the first case, Avrami, Ozawa, Mo, Cazé, and Friedman methodologies were applied. The isoconversional approach developed by Vyazovkin allowed also the determination of a secondary nucleation parameter of 2.10 × 105 K2 and estimating a temperature close to 10 °C for the maximum crystal growth rate. Similar values (i.e., 2.22 × 105 K2 and 9 °C) were evaluated from non-isothermal Avrami parameters. All experimental data corresponded to a limited region where the polymer crystallized according to a single regime. Negative and ringed spherulites were always obtained from the non-isothermal crystallization of P4HB from the melt. The texture of spherulites was dependent on the crystallization temperature, and specifically, the interring spacing decreased with the decrease of the crystallization temperature (Tc). Synchrotron data indicated that the thickness of the constitutive lamellae varied with the cooling rate, being deduced as a lamellar insertion mechanism that became more relevant when the cooling rate increased. POM non-isothermal measurements were also consistent with a single crystallization regime and provided direct measurements of the crystallization growth rate (G). Analysis of the POM data gave a secondary nucleation constant and a bell-shaped G-Tc dependence that was in relative agreement with DSC analysis. All non-isothermal data were finally compared with information derived from previous isothermal analyses.

scholarly journals Shear-Induced and Nanofiber-Nucleated Crystallization of Novel Aliphatic–Aromatic Copolyesters Delineated for In Situ Generation of Biodegradable Nanocomposites

Polymers ◽  
2021 ◽  
Vol 13 (14) ◽  
pp. 2315
Author(s):  
Ramin Hosseinnezhad
Keyword(s):  
Shear Rate ◽  
Cooling Rate ◽  
Isothermal Crystallization ◽  
Cellulose Nanofibers ◽  
Crystallization Time ◽  
Nucleation Density ◽  
Shear Rates ◽  
Biodegradable Nanocomposites ◽  
In Situ Generation

The shear-induced and cellulose-nanofiber nucleated crystallization of two novel aliphatic–aromatic copolyesters is outlined due to its significance for the in situ generation of biodegradable nanocomposites, which require the crystallization of nanofibrous sheared inclusions at higher temperatures. The shear-induced non-isothermal crystallization of two copolyesters, namely, poly(butylene adipate-co-succinate-co-glutarate-co-terephthalate) (PBASGT) and poly(butylene adipate-co-terephthalate) (PBAT), was studied following a light depolarization technique. To have a deep insight into the process, the effects of the shear rate, shear time, shearing temperature and cooling rate on the initiation, kinetics, growth and termination of crystals were investigated. Films of 60 μm were subjected to various shear rates (100–800 s−1) for different time intervals during cooling. The effects of the shearing time and increasing the shear rate were found to be an elevated crystallization temperature, increased nucleation density, reduced growth size of lamella stacks and decreased crystallization time. Due to the boosted nucleation sites, the nuclei impinged with each other quickly and growth was hindered. The effect of the cooling rate was more significant at lower shear rates. Shearing the samples at lower temperatures, but still above the nominal melting point, further shifted the non-isothermal crystallization to higher temperatures. As a result of cellulose nanofibers’ presence, the crystallization of PBAT, analyzed by DSC, was shifted to higher temperatures.

The effect of cooling rate on crystallization behavior and tensile properties of CF/PEEK composites

2021 ◽  
Vol 0 (0) ◽  
Author(s):  
Guangming Dai ◽  
Lihua Zhan ◽  
Chenglong Guan ◽  
Minghui Huang
Keyword(s):  
Cooling Rate ◽  
Crystallization Temperature ◽  
Crystallization Behavior ◽  
Crystalline Polymer ◽  
Scanning Calorimetry ◽  
Nonisothermal Crystallization ◽  
Cooling Rates ◽  
Control Range ◽  
Temperature Range ◽  
Transverse Tensile

Abstract In this study, the differential scanning calorimetry (DSC) tests were performed to measure the nonisothermal crystallization behavior of carbon fiber reinforced polyether ether ketone (CF/PEEK) composites under different cooling rates. The characteristic parameters of crystallization were obtained, and the nonisothermal crystallization model was established. The crystallization temperature range of the material at different cooling rates was predicted by the model. The unidirectional laminates were fabricated at different cooling rates in the crystallization temperature range. The results showed that the crystallization temperature range shifted to a lower temperature with the increase of cooling rate, the established nonisothermal crystallization model was consistent with the DSC test results. It is feasible to shorten the cooling control range from the whole process to the crystallization range. The crystallinity and transverse tensile strength declined significantly with the increase of the cooling rate in the crystallization temperature range. The research results provided theoretical support for the selection of cooling conditions and temperature control range, which could be applied to the thermoforming process of semi-crystalline polymer matrixed composites to improve the manufacturing efficiency.

Non-Isothermal Crystallization Kinetics of Graphene Oxide-Carbon Nanotubes Hybrids / Polyamide 6 Composites

2019 ◽  
Vol 41 (3) ◽  
pp. 394-394
Author(s):  
Zhi Qiang Wang Zhi Qiang Wang ◽  
Yong Ke Zhao and Xiang Feng Wu Yong Ke Zhao and Xiang Feng Wu
Keyword(s):  
Carbon Nanotubes ◽  
Graphene Oxide ◽  
Cooling Rate ◽  
Crystallization Kinetics ◽  
Isothermal Crystallization ◽  
Crystallization Rate ◽  
Polyamide 6 ◽  
Degree Of Crystallinity ◽  
Isothermal Crystallization Kinetics ◽  
Kinetics Of

The hybrids combined by nano-materials with different dimensions usually possess much better enhancement effects than single one. Graphene oxide-carbon nanotubes hybrids / polyamide 6 composites has been fabricated. The non-isothermal crystallization kinetics of the as-prepared samples was discussed. Research results showed that increasing the cooling rate was in favor of increasing the crystallization rate and the degree of crystallinity for the as-prepared samples. Moreover, the crystallization rate was first decreased and then increased with increasing the hybrids loading. Furthermore, the crystallization mechanism was changed with increasing the crystallization temperature and the cooling rate. The nucleation and growth modes of the non-isothermal crystallization could be classified into three different types, according to the Ozawa’s theory. These complicated results could be attributed to the important role of crystallization rate as well as the simultaneous hindering and promoting effects of the as-prepared hybrids. This work has reference values for understanding the crystallization kinetics of the polyamide 6-based composites.

scholarly journals Isothermal Crystallization and Rheology Properties of Isotactic Polypropylene/Bacterial Cellulose Composite

Polymers ◽  
2018 ◽  
Vol 10 (11) ◽  
pp. 1284 ◽  
Author(s):  
Bo Wang ◽  
Fu-hua Lin ◽  
Xiang-yang Li ◽  
Zhong-wei Zhang ◽  
Xiao-rong Xue ◽  
...  
Keyword(s):  
Bacterial Cellulose ◽  
Storage Modulus ◽  
Isotactic Polypropylene ◽  
Crystallization Temperature ◽  
Isothermal Crystallization ◽  
Complex Viscosity ◽  
Isothermal Crystallization Kinetics ◽  
Interfacial Compatibility ◽  
And Storage ◽  
Better Than

Bacterial cellulose (BC) is a new kind of cellulose with great potential in enhancing preparation of isotactic Polypropylene (iPP) composites, which have been found with excellent performance. However, the interface compatibility between BC and iPP is poor. In this study, iPP/BC composites were prepared by solution mixing. Esterification modified BC (CO) and Maleic anhydride grafted polypropylene (MAPP) added as a compatibilizer was both used to improve the interfacial compatibility of the iPP/BC composites. The rheology and isothermal crystallization behavior of the composites was tested and discussed. The result shows that the complex viscosity and storage modulus of the composite significantly increase in the rule iPP, iPP/BC2, iPP/CO2, and M-iPP/BC3, which indicates that the compatibility of the composite increases as this rule. According to the isothermal crystallization kinetics result, the crystal growth mode of iPP was not affected by the addition of BC and the interfacial compatibility. The spherulite growth rate of the iPP/BC composite increases with increasing crystallization temperature. Especially, the value decreases as the same rule with the complex viscosity and storage modulus of the composite at the same isothermal crystallization temperature. These results suggest that the interface compatibility of iPP/BC composites is greatly improved and the interface compatibility of the M-iPP/BC3 is better than the iPP/CO2.

scholarly journals The effect of isothermal crystallization on mechanical properties of poly(ethylene 2,5-furandicarboxylate)

e-Polymers ◽  
2021 ◽  
Vol 22 (1) ◽  
pp. 1-11
Author(s):  
Wei Zhang ◽  
Qingyin Wang ◽  
Gongying Wang ◽  
Shaoying Liu
Keyword(s):  
Mechanical Properties ◽  
Intrinsic Viscosity ◽  
Crystallization Temperature ◽  
Isothermal Crystallization ◽  
Tensile Modulus ◽  
Optical Microscope ◽  
Crystallization Time ◽  
Scanning Calorimetry ◽  
Crystallization Properties ◽  
Poly Ethylene

Abstract The effects of isothermal crystallization temperature/time on mechanical properties of bio-based polyester poly(ethylene 2,5-furandicarboxylate) (PEF) were investigated. The intrinsic viscosity, crystallization properties, thermal properties, and microstructure of PEF were characterized using ubbelohde viscometer, X-ray diffraction, polarizing optical microscope, differential scanning calorimetry, and scanning electron microscopy. The PEF sample isothermal crystallized at various temperatures for various times was denoted as PEF-T-t. The results showed that the isothermal crystallization temperature affected the mechanical properties of PEF-T-30 by simultaneously affecting its crystallization properties and intrinsic viscosity. The isothermal crystallization time only affected the crystallization properties of PEF-110-t. The crystallinity of PEF-110-40 was 17.1%. With small crystal size, poor regularity, and α′-crystal, PEF-110-40 can absorb the energy generated in the tensile process to the maximum extent. Therefore, the best mechanical properties can be obtained for PEF-110-40 with the tensile strength of 43.55 MPa, the tensile modulus of 1,296 MPa, and the elongation at a break of 13.36%.

Morphology, Crystalline Structure and Isothermal Crystallization Kinetics of Polybutylene Terephthalate/Montmorillonite Nanocomposites

2005 ◽  
Vol 13 (1) ◽  
pp. 61-71 ◽  
Author(s):  
Defeng Wu ◽  
Chixing Zhou ◽  
Xie Fan ◽  
Dalian Mao ◽  
Zhang Bian
Keyword(s):  
Activation Energy ◽  
Crystallization Kinetics ◽  
Crystallization Temperature ◽  
Isothermal Crystallization ◽  
Polymer Chains ◽  
Isothermal Crystallization Kinetics ◽  
Clay Particles ◽  
Nucleation Sites ◽  
Kinetics Of ◽  
Montmorillonite Nanocomposites

The melt intercalation method was employed to prepare poly(butylene terepathalate)/montmorillonite nanocomposites, and their microstructure was characterized by wide angle X-ray diffraction and transmission electron microscopy. The XRD results showed that the crystalline plane such as (010), (111), (100) was smaller than that of pristine PBT, which indicates that the crystallite size of PBT in the nanocomposites could be diminished by adding clay. Moreover, the isothermal crystallization kinetics of PBT and PBT/MMT nanocomposites was investigated by differential scanning calorimetry (DSC). During isothermal crystallization, the development of crystallinity with time was analysed by the Avrami equation. The results show that very small amounts of clay dramatically increased the rate of crystallization and high clay concentrations reduced the rate of crystallization at the low crystallization temperatures. At low concentrations of clay, the distance between dispersed platelets was large so it was relatively easy for the additional nucleation sites to incorporate surrounding polymer, and the crystal nucleus was formatted easily. However, at high concentrations of clay, the diffusion of polymer chains to the growing crystallites was hindered by large clay particles, despite the formation of additional nucleation sites by the clay layers. At the higher crystallization temperature, the crystallization of the nanocomposites was slower than that of the pure PBT under the experimental conditions, which means that with the increase in chains mobility at the high crystallization temperature, the crystal nuclei are harder to format, and the hindering effect of clay particles on the polymer chains was stronger than the nucleating effect of the layers. In addition, the activation energies of crystallization for PBT and its nanocomposites were calculated by the Arrhenius relationship, and the results showed that the nanocomposites with a low clay content had the lower activation energy values than PBT, while high amounts of clay increased the activation energy of PBT.

scholarly journals The effect of hydroxyapatite nanoparticles on crystallization and thermomechanical properties of PLLA matrix

2017 ◽  
Vol 89 (1) ◽  
pp. 125-140 ◽  
Author(s):  
Ioanna-Georgia I. Athanasoulia ◽  
Maximos N. Christoforidis ◽  
Dimitrios M. Korres ◽  
Petroula A. Tarantili
Keyword(s):  
Crystallization Temperature ◽  
Isothermal Crystallization ◽  
Crystallization Behavior ◽  
Crystallization Kinetic ◽  
Crystallization Rate ◽  
Melting Behavior ◽  
Thermomechanical Properties ◽  
Cold Crystallization ◽  
Crystallization Experiments ◽  
Twin Screw

AbstractIn this study, hydroxyapatite (HA) was incorporated in a poly(L-lactic acid) (PLLA) matrix and the thermal properties and crystallization behavior of the derived composites were investigated. The nanocomposites, containing 0–20 wt% HA, were prepared by melt extrusion employing a twin-screw extruder. XRD experiments verified an increase in the intensity of the characteristic diffraction peak of the α-form crystalline phase of PLLA with increasing HA content. By DSC experiments it was observed that the presence of HA increased the crystallinity during cold crystallization, leading to a shift of cold-crystallization temperature to lower values and to an increase in the melting temperature of the PLLA phase. Isothermal crystallization experiments at 100, 110, 115 and 120°C, revealed a maximum in crystallization kinetic around 100°C after the addition of HA compared to 115°C for pure PLLA. The crystallization rate of PLLA matrix in the nanocomposites decreased with increasing crystallization temperature. By using the Avrami and Lauritzen-Hoffman equations the exponent n was calculated in the range 2–3 and a theoretical approach verified that the HA/PLLA systems belong to Regime II of crystallization behavior. The investigated melting behavior of PLLA was attributed to better organized crystalline structure with increasing isothermal crystallization temperatures and might be related with the longer time necessary for the completion of crystallization.

The Melting Behavior of Poly(Ethylene Terephthalate)/ Attapulgite Nanocomposites

2013 ◽  
Vol 773 ◽  
pp. 530-533
Author(s):  
Chen Liu ◽  
Xiang Hui Lu ◽  
Xue Qi ◽  
Peng Li
Keyword(s):  
Crystallization Temperature ◽  
Isothermal Crystallization ◽  
Ethylene Terephthalate ◽  
Melting Process ◽  
Melting Behavior ◽  
Crystallization Time ◽  
Scanning Calorimetry ◽  
Poly Ethylene Terephthalate ◽  
Poly Ethylene ◽  
Crystallization From The Melt

The melting and recrystallization behavior of Poly(ethylene terephthalate) (PET)/ Attapulgite(At)nanocomposites after isothermal crystallization from the melt was studied by Step-scan differential scanning calorimetry (SDSC). The influence of At contents, crystallization temperature and crystallization time on the melting process were examined. Two melting endotherms(in the SDSC CP.A curves, reversible part) and one recrystallization exotherm (in the SDSC CP.IsoK curves, irreversible part)of PET/At nanocomposites after isothermal crystallization were observed during the melt process. This ascribes to the melting-recrystallization mechanism .The low temperature endotherm attributes to the melting of primary crystal formed during the isothermal treating and the high temperature endotherm resulting from the melting of recrystallization materials. The reason why more recrystallization happened with the increase of At content was given and the process of recrystallization was described in detail. The effects of crystal perfection and recrystallization were minimized by increasing of crystallization temperature and time.

Sign in / Sign up

Export Citation Format

Share Document