The effect of high-pressure gas on the mechanical properties of polymethyl methacrylate

1974 ◽  
Vol 8 (5) ◽  
pp. 587-589
Author(s):  
G. B. Okonishnikov ◽  
V. P. Skripov
Keyword(s):  
Mechanical Properties ◽  
High Pressure ◽  
Polymethyl Methacrylate

Mechanical properties of clays at high pressure

1980 ◽  
Vol 85 (B3) ◽  
pp. 1462-1468 ◽  
Author(s):  
Chi-Yuen Wang ◽  
Nai-Hsien Mao ◽  
Francis T. Wu
Keyword(s):  
Mechanical Properties ◽  
High Pressure

Optically Transparent Polymethyl Methacrylate Composites made with Glass Fibers of Varying Refractive Index

1997 ◽  
Vol 12 (4) ◽  
pp. 1091-1101 ◽  
Author(s):  
Seunggu Kang ◽  
Hongy Lin ◽  
Delbert E. Day ◽  
James O. Stoffer
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Refractive Index ◽  
Mechanical Strength ◽  
Glass Fiber ◽  
Polymethyl Methacrylate ◽  
Optical Transmission ◽  
Annealing Temperature ◽  
Glass Fibers ◽  
Optically Transparent

The dependence of the optical and mechanical properties of optically transparent polymethyl methacrylate (PMMA) composites on the annealing temperature of BK10 glass fibers was investigated. Annealing was used to modify the refractive index (R.I.) of the glass fiber so that it would more closely match that of PMMA. Annealing increased the refractive index of the fibers and narrowed the distribution of refractive index of the fibers, but lowered their mechanical strength so the mechanical properties of composites reinforced with annealed fibers were not as good as for composites containing as-pulled (chilled) glass fibers. The refractive index of as-pulled 17.1 μm diameter fibers (R.I. = 1.4907) increased to 1.4918 and 1.4948 after annealing at 350 °C to 500 °C for 1 h or 0.5 h, respectively. The refractive index of glass fibers annealed at 400 °C/1 h best matched that of PMMA at 589.3 nm and 25 °C, so the composite reinforced with those fibers had the highest optical transmission. Because annealed glass fibers had a more uniform refractive index than unannealed fibers, the composites made with annealed fibers had a higher optical transmission. The mechanical strength of annealed fiber/PMMA composites decreased as the fiber annealing temperature increased. A composite containing fibers annealed at 450 °C/1 h had a tensile strength 26% lower than that of a composite made with as-pulled fibers, but 73% higher than that for unreinforced PMMA. This decrease was avoided by treating annealed fibers with HF. Composites made with annealed and HF (10 vol. %)-treated (for 30 s) glass fibers had a tensile strength (∼200 MPa) equivalent to that of the composites made with as-pulled fibers. However, as the treatment time in HF increased, the tensile strength of the composites decreased because of a significant reduction in diameter of the glass fiber which reduced the volume percent fiber in the composite.

Highly Dense Amorphous Si2 BC3 N Monoliths with Excellent Mechanical Properties Prepared by High Pressure Sintering

2015 ◽  
Vol 98 (12) ◽  
pp. 3782-3787 ◽  
Author(s):  
Bin Liang ◽  
Zhihua Yang ◽  
Jiancun Rao ◽  
Delong Cai ◽  
Xiaoming Duan ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
High Pressure ◽  
High Pressure Sintering

Mechanical Characterization of UV Photopolymerized PMMA with Different Photo-Initiator Concentration

2021 ◽  
Vol 903 ◽  
pp. 11-16
Author(s):  
M.A. Manjunath ◽  
K. Naveen ◽  
Prakash Vinod ◽  
N. Balashanmugam ◽  
M.R. Shankar
Keyword(s):  
Mechanical Properties ◽  
Light Source ◽  
Polymethyl Methacrylate ◽  
Biomedical Applications ◽  
Mechanical Characterization ◽  
Uv Light ◽  
Curing Time ◽  
Uv Led ◽  
Pmma Resin

Polymethyl methacrylate (PMMA) is one among few known photo-polymeric resin useful in lithography for fabricating structures having better mechanical properties to meet the requirement in electronics and biomedical applications. This study explores the effect of Photo Initiator (PI) concentration and also curing time on strength and hardness of Polymethyl methacrylate (PMMA) obtained by UV photopolymerization of Methyl methacrylate (MMA) monomer. The UV LED light source operating at the wavelength of 364 nm is used with Benzoin Ethyl Ether (BEE) as photo initiator. The curing of PMMA resin is supported with peltier cooling device placed at the bottom of the UV light source. The characterisation study of UV photo cured PMMA is analysed through nano indenter (Agilent Technologies-G200). The current work investigates the influence of PI concentration and curing time in achieving maximum mechanical properties for UV photopolymerized PMMA.

Sign in / Sign up

Export Citation Format

Share Document