Transient fatigue crack growth caused by change in environmental conditions

1985 ◽  
Vol 4 (12) ◽  
pp. 1498-1500 ◽  
Author(s):  
Susumu Horibe ◽  
Masae Sumita
Keyword(s):  
Fatigue Crack ◽  
Fatigue Crack Growth ◽  
Crack Growth ◽  
Environmental Conditions

Fatigue Crack Growth Rate and Fracture Toughness of API5L X65 in Sweet Environments

2013 ◽  
Author(s):  
Michael A. Tognarelli ◽  
Ramgopal Thodla ◽  
Steven Shademan
Keyword(s):  
Fracture Toughness ◽  
Growth Rate ◽  
Fatigue Crack ◽  
Crack Growth Rate ◽  
Fatigue Crack Growth ◽  
Crack Growth ◽  
Fatigue Crack Growth Rate ◽  
Environmental Conditions ◽  
Initiation Toughness ◽  
Diffusible Hydrogen

Corrosion fatigue and fracture toughness in sour environments of APIX65 5L have typically been studied in relatively severe environments like NACE A and NACE B solutions. There are very limited data in sweet and mildly sour environments that are of interest in various applications. This paper presents fatigue crack growth frequency scans in a range of sweet and mildly sour environments as well as on different microstructures: Parent Pipe, Heat Affected Zone (HAZ) and Weld Center Line (WCL). The fatigue crack growth rate (FCGR) increased with decreasing frequency and reached a plateau value at low frequencies. FCGR in the sweet environments that were investigated did exhibit a frequency dependence (increasing with decreasing frequency) and had plateau FCGR in the range of 10–20× the in-air values. In the mildly sour environments that were investigated, FCGR was found to be about 25 to 30× higher than the in-air values. By comparison, in NACE A environments the FCGR is typically about 50× higher than the in-air values. The FCGRs of parent pipe and HAZ were found to be similar over a range of environments, whereas the WCL FCGR data were consistently lower by about a factor of 2×. The lower FCGR of the WCL is likely due to the lower concentration of diffusible hydrogen in the weld. FCGRs as a function of ΔK (stress integrity factor range) were measured on parent pipe at the plateau frequency. The measured Paris law curves were consistent with the frequency scan data. Rising displacement fracture toughness tests were performed in a range of sweet and sour environments to determine the R-curve behavior. Tests were performed in-situ at a slow K-rate of 0.05Nmm−3/2/s over a range of environmental conditions on parent pipe. The initiation toughness and the slope of the R-curve decreased sharply in the sour environments. The initiation toughness and slopes were largely independent of the notch location as well as environmental conditions. Typical values of initiation toughness were in the range of 90–110N/mm.

A discrete dislocation analysis of fatigue crack growth

2001 ◽  
Vol 11 (PR5) ◽  
pp. Pr5-69-Pr5-75
Author(s):  
V. S. Deshpande ◽  
H. H.M. Cleveringa ◽  
E. Van der Giessen ◽  
A. Needleman
Keyword(s):  
Fatigue Crack ◽  
Fatigue Crack Growth ◽  
Crack Growth ◽  
Discrete Dislocation

Fatigue Investigation of Elastomeric Structures

2010 ◽  
Vol 38 (3) ◽  
pp. 194-212 ◽  
Author(s):  
Bastian Näser ◽  
Michael Kaliske ◽  
Will V. Mars
Keyword(s):  
Fatigue Crack ◽  
Fatigue Crack Growth ◽  
Crack Growth ◽  
Material Behavior ◽  
Period Effect ◽  
Numerical Representation ◽  
Material Force ◽  
Strain Behavior ◽  
Dissipative Effects ◽  
Elastomeric Materials

Abstract Fatigue crack growth can occur in elastomeric structures whenever cyclic loading is applied. In order to design robust products, sensitivity to fatigue crack growth must be investigated and minimized. The task has two basic components: (1) to define the material behavior through measurements showing how the crack growth rate depends on conditions that drive the crack, and (2) to compute the conditions experienced by the crack. Important features relevant to the analysis of structures include time-dependent aspects of rubber’s stress-strain behavior (as recently demonstrated via the dwell period effect observed by Harbour et al.), and strain induced crystallization. For the numerical representation, classical fracture mechanical concepts are reviewed and the novel material force approach is introduced. With the material force approach at hand, even dissipative effects of elastomeric materials can be investigated. These complex properties of fatigue crack behavior are illustrated in the context of tire durability simulations as an important field of application.

Sign in / Sign up

Export Citation Format

Share Document