Selecting the quenching medium for aluminum alloys

1989 ◽  
Vol 31 (3) ◽  
pp. 164-166 ◽  
Author(s):  
Yu. G. Krotov ◽  
D. Kh. Khamidullin ◽  
S. N. Anan'in
Keyword(s):  
Aluminum Alloys ◽  
Quenching Medium

Analytical Electron Microscopy Study of Second-Phase Particles in 7075 and 7475 Aluminum Alloys

1985 ◽  
Vol 43 ◽  
pp. 348-349
Author(s):  
M. Raghavan ◽  
J. Y. Koo ◽  
J. W. Steeds ◽  
B. K. Park
Keyword(s):  
Aluminum Alloys ◽  
Silicon Oxide ◽  
Analytical Electron Microscopy ◽  
Microscopy Study ◽  
Electron Microscopy Study ◽  
Partial Substitution ◽  
Second Phase ◽  
X Ray ◽  
Second Phase Particles ◽  
Almost All

X-ray microanalysis and Convergent Beam Electron Diffraction (CBD) studies were conducted to characterize the second phase particles in two commercial aluminum alloys -- 7075 and 7475. The second phase particles studied were large (approximately 2-5μm) constituent phases and relatively fine ( ∼ 0.05-1μn) dispersoid particles, Figures 1A and B. Based on the crystal structure and chemical composition analyses, the constituent phases found in these alloys were identified to be Al7Cu2Fe, (Al,Cu)6(Fe,Cu), α-Al12Fe3Si, Mg2Si, amorphous silicon oxide and the modified 6Fe compounds, in decreasing order of abundance. The results of quantitative X-ray microanalysis of all the constituent phases are listed in Table I. The data show that, in almost all the phases, partial substitution of alloying elements occurred resulting in small deviations from the published stoichiometric compositions of the binary and ternary compounds.

Electrochemical Impedance Characteristics of Sintered 7075 Aluminum Alloy Under Ssrt Condition

2013 ◽  
Vol 58 (2) ◽  
pp. 505-508 ◽  
Author(s):  
S. Sunada ◽  
N. Nunomura
Keyword(s):  
Aluminum Alloys ◽  
Complex Shape ◽  
Electrochemical Impedance ◽  
Ingot Metallurgy ◽  
View Point ◽  
Corrosion Properties ◽  
Electrochemical Tests ◽  
Impedance Characteristics ◽  
Polarization Test ◽  
Conventional Ingot

Powder metallurgy (P/M) process has the advantage of better formability to fabricate complex shape products without machining and welding. And recently this P/M process has been applied to the production of aluminum alloys. The P/M aluminum alloys thus produced also have received considerable interest because of their fine and homogeneous structure. Many papers have been published on the mechanical properties of the aluminum alloys produced by P/M process while there have been few on their corrosion properties from the view point of electrochemistry. In this experiment, therefore, two kinds of 7075 aluminum alloys prepared by the conventional ingot metallurgy (I/M) process and P/M process were used, I/M material is commercially available. and their corrosion behavior were investigated through the electrochemical tests such as potentiodynamic polarization test, slow rate strain tensile (SSRT) test and electrochemical impedance spectroscopy (EIS) measurement under SSRT test in the corrosion solution and the deionized water.

ALCOA QC-10

Alloy Digest ◽  
2009 ◽  
Vol 58 (7) ◽  
Keyword(s):  
Heat Transfer ◽  
Thermal Conductivity ◽  
Aluminum Alloys ◽  
Physical Properties ◽  
Tensile Properties ◽  
Mold Material ◽  
Cast Products

Abstract Aluminum has long been accepted as a mold material. This alloy has a combination of faster machining, highest heat transfer, lighter weight, higher strength in thick sections, and greater thermal conductivity than other aluminum alloys. This datasheet provides information on physical properties, hardness, elasticity, and tensile properties. It also includes information on forming and machining. Filing Code: AL-423. Producer or source: Alcoa Forged and Cast Products.

Sign in / Sign up

Export Citation Format

Share Document