Influence of grain size and ?-phase stability on the fatigue limit of high-strength austenitic steels

1981 ◽  
Vol 23 (5) ◽  
pp. 354-359
Author(s):  
E. I. Shchedrin ◽  
V. V. Sagaradze ◽  
K. A. Malyshev
Keyword(s):  
Grain Size ◽  
Fatigue Limit ◽  
Phase Stability ◽  
High Strength ◽  
Austenitic Steels

Grain Refinement and Mechanical Properties of a Metastable Austenitic Fe-Cr-Ni-Mn Alloy

2005 ◽  
Vol 475-479 ◽  
pp. 43-48 ◽  
Author(s):  
Yunqing Ma ◽  
Jae Eun Jin ◽  
Young Kook Lee
Keyword(s):  
Grain Size ◽  
Work Hardening ◽  
High Strength ◽  
Austenitic Steels ◽  
Nano Materials ◽  
Fundamental Research ◽  
Cold Rolled ◽  
Austenite Grains ◽  
Hot Rolled ◽  
Conventional Rolling

A lot of works for developing the structural nano-materials have been performed all over the world in recent years. Severe deformation techniques like HPT, ECPA and ARB have been applied to different materials such as Al, Cu, Ti and several steels. Such techniques greatly reduced the grain size and improved the yield and tensile strengths. However, the elongation of the materials is greatly decreased due to the small amount of work hardening, and these techniques do not seem suitable for the mass production. Therefore, this study has been carried out as a fundamental research for developing austenitic steels with high strength and good elongation using a conventional rolling and annealing processes. Fe-0.1%C-10%Cr-5%Ni-8%Mn alloy was melted, homogenized, hot rolled, and cold rolled at room temperature to transform γ austenite to α ’ martensite. After that, the specimens were annealed just above its reverse transformation finish temperature (Af) to obtain the fine reversed austenite grains. The grain size of the metastable austenitic steel was successfully refined to less than 200nm by repeating rolling and annealing processes. The resultant nanocrystalline material shows not only high strength but also large elongation because the work hardening ability is enhanced by the strain-induced martensitic transformation during the tensile test.

Fatigue of Ultra-Fine Grained α-Brass

2014 ◽  
Vol 891-892 ◽  
pp. 1125-1130
Author(s):  
Yoshikazu Nakai ◽  
Takuto Imanaka ◽  
Daiki Shiozawa
Keyword(s):  
Plastic Deformation ◽  
Grain Size ◽  
Tensile Strength ◽  
Ultimate Tensile Strength ◽  
Severe Plastic Deformation ◽  
Fatigue Limit ◽  
High Strength ◽  
Angular Pressing ◽  
Fine Grain ◽  
Proof Strength

Combined methods to obtain ultra-fine grain (UFG) α-brass samples are proposed. Severe plastic deformation followed by recrystallization was conducted, where multiple rolling and equal channel angular pressing (ECAP) were employed. Recrystallization was accomplished by heat-treatment after the severe plastic deformation, and the grain size after the severe plastic deformation was decreased. By multiple rolling, plates with thickness of 0.1 mm and grain size of 1.0 μm were obtained. By ECAP process, square bar with cross-section of 6 mm × 6 mm and minimum grain size of 4.1 μm was obtained. The 0.2 % proof strength, ultimate tensile strength, and fatigue limit were increased with the value of inverse square root of grain size (Hall-Petch relationship). Then, the 0.2 % proof strength of UFG brass was tenfold, the ultimate tensile strength and the fatigue limit were two fold increases from the conventional α-brass. Because of the high strength, the scatter of fatigue strength of UFG brass was large, which reflects the sensitivity to defects in material.

DOWMETAL ZK60A

Alloy Digest ◽  
1952 ◽  
Vol 1 (1) ◽  
Keyword(s):  
Fracture Toughness ◽  
Grain Size ◽  
Corrosion Resistance ◽  
High Resistance ◽  
High Strength ◽  
Heat Treating ◽  
Bend Strength ◽  
Chemical Company ◽  
Resistance To Stress ◽  
Extrusion Alloy

Abstract Dowmetal ZK60A is an ageable extrusion alloy for use where high strength magnesium extrusions with good toughness are required. It has small grain size, low notch sensitivity and a relatively high resistance to stress corrosion. This datasheet provides information on composition, physical properties, tensile properties, and compressive, shear, bearing, and bend strength as well as fracture toughness. It also includes information on corrosion resistance as well as forming, heat treating, machining, joining, and surface treatment. Filing Code: Mg-1. Producer or source: The Dow Chemical Company.

ALLEGHENY LUDLUM TYPE 205

Alloy Digest ◽  
1997 ◽  
Vol 46 (10) ◽  
Keyword(s):  
Mechanical Properties ◽  
Stainless Steel ◽  
Corrosion Resistance ◽  
Physical Properties ◽  
Tensile Properties ◽  
Magnetic Permeability ◽  
Cold Working ◽  
High Strength ◽  
Heat Treating ◽  
Austenitic Steels

Abstract Allegheny Stainless Type 205 is a chromium-manganese nitrogen austenitic high strength stainless steel that maintains its low magnetic permeability even after large amounts of cold working. Annealed Type 205 has higher mechanical properties than any of the conventional austenitic steels-and for any given strength level, the ductility of Type 205 is comparable to that of Type 301. This datasheet provides information on composition, physical properties, hardness, elasticity, and tensile properties as well as fatigue. It also includes information on corrosion resistance as well as heat treating, machining, and joining. Filing Code: SS-640. Producer or source: Allegheny Ludlum Corporation. Originally published March 1996, revised October 1997.

scholarly journals Grain Size Evolution and Mechanical Properties of Nb, V–Nb, and Ti–Nb Boron Type S1100QL Steels

Metals ◽  
2021 ◽  
Vol 11 (3) ◽  
pp. 492
Author(s):  
Jan Foder ◽  
Jaka Burja ◽  
Grega Klančnik
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Grain Size ◽  
Hot Forging ◽  
Size Control ◽  
High Strength ◽  
Fatigue Properties ◽  
Titanium Addition ◽  
Austenite Grain Size ◽  
Size Evolution

Titanium additions are often used for boron factor and primary austenite grain size control in boron high- and ultra-high-strength alloys. Due to the risk of formation of coarse TiN during solidification the addition of titanium is limited in respect to nitrogen. The risk of coarse nitrides working as non-metallic inclusions formed in the last solidification front can degrade fatigue properties and weldability of the final product. In the presented study three microalloying systems with minor additions were tested, two without any titanium addition, to evaluate grain size evolution and mechanical properties with pre-defined as-cast, hot forging, hot rolling, and off-line heat-treatment strategy to meet demands for S1100QL steel. Microstructure evolution from hot-forged to final martensitic microstructure was observed, continuous cooling transformation diagrams of non-deformed austenite were constructed for off-line heat treatment, and the mechanical properties of Nb and V–Nb were compared to Ti–Nb microalloying system with a limited titanium addition. Using the parameters in the laboratory environment all three micro-alloying systems can provide needed mechanical properties, especially the Ti–Nb system can be successfully replaced with V–Nb having the highest response in tensile properties and still obtaining satisfying toughness of 27 J at –40 °C using Charpy V-notch samples.

scholarly journals A Physical-Based Plane Stress Constitutive Model for High Strength AA7075 under Hot Forming Conditions

Metals ◽  
2021 ◽  
Vol 11 (2) ◽  
pp. 314
Author(s):  
Fulong Chen ◽  
Haitao Qu ◽  
Wei Wu ◽  
Jing-Hua Zheng ◽  
Shuguang Qu ◽  
...  
Keyword(s):  
Grain Size ◽  
Aluminum Alloy ◽  
Plane Stress ◽  
Metal Forming ◽  
Electron Backscatter Diffraction ◽  
High Strength ◽  
Material Model ◽  
Hot Forming ◽  
Industrial Processing ◽  
Average Grain Size

Physicallybased constitutive equations are increasingly used for finite element simulations of metal forming processes due to the robust capability of modelling of underlying microstructure evolutions. However, one of thelimitations of current models is the lack of practical validation using real microstructure data due to the difficulties in achieving statistically meaningful data at a sufficiently large microstructure scale. Particularly, dislocation density and grain size governing the hardening in sheet deformation are of vital importance and need to be precisely quantified. In this paper, a set of dislocation mechanics-based plane stress material model is constructed for hot forming aluminum alloy. This material model is applied to high strength 7075 aluminum alloy for the prediction of the flow behaviorsconditioned at 300–400 °C with various strain rates. Additionally, an electron backscatter diffraction (EBSD) technique was applied to examine the average grain size and geometrical necessary dislocation (GND) density evolutions, enabling both macro- and micro- characteristics to be successfully predicted. In addition, to simulate the experienced plane stress states in sheet metal forming, the calibrated model is further extended to a plane stress stateto accuratelypredict the forming limits under hot conditions.The comprehensively calibrated material model could be used for guidinga better selection of industrial processing parameters and designing process windows, taking into account both the formed shape as well as post formed microstructure and, hence, properties.

scholarly journals Overview of HSS Steel Grades Development and Study of Reheating Condition Effects on Austenite Grain Size Changes

Materials ◽  
2021 ◽  
Vol 14 (8) ◽  
pp. 1988
Author(s):  
Tibor Kvackaj ◽  
Jana Bidulská ◽  
Róbert Bidulský
Keyword(s):  
Mechanical Properties ◽  
Grain Size ◽  
High Strength Steel ◽  
Single Phase ◽  
Hsla Steel ◽  
High Strength ◽  
Strength Properties ◽  
Austenite Grain Size ◽  
Austenite Grain ◽  
Steel Grades

This review paper concerns the development of the chemical compositions and controlled processes of rolling and cooling steels to increase their mechanical properties and reduce weight and production costs. The paper analyzes the basic differences among high-strength steel (HSS), advanced high-strength steel (AHSS) and ultra-high-strength steel (UHSS) depending on differences in their final microstructural components, chemical composition, alloying elements and strengthening contributions to determine strength and mechanical properties. HSS is characterized by a final single-phase structure with reduced perlite content, while AHSS has a final structure of two-phase to multiphase. UHSS is characterized by a single-phase or multiphase structure. The yield strength of the steels have the following value intervals: HSS, 180–550 MPa; AHSS, 260–900 MPa; UHSS, 600–960 MPa. In addition to strength properties, the ductility of these steel grades is also an important parameter. AHSS steel has the best ductility, followed by HSS and UHSS. Within the HSS steel group, high-strength low-alloy (HSLA) steel represents a special subgroup characterized by the use of microalloying elements for special strength and plastic properties. An important parameter determining the strength properties of these steels is the grain-size diameter of the final structure, which depends on the processing conditions of the previous austenitic structure. The influence of reheating temperatures (TReh) and the holding time at the reheating temperature (tReh) of C–Mn–Nb–V HSLA steel was investigated in detail. Mathematical equations describing changes in the diameter of austenite grain size (dγ), depending on reheating temperature and holding time, were derived by the authors. The coordinates of the point where normal grain growth turned abnormal was determined. These coordinates for testing steel are the reheating conditions TReh = 1060 °C, tReh = 1800 s at the diameter of austenite grain size dγ = 100 μm.

scholarly journals Effect of Rare Earth Ce on Deep Stamping Properties of High-Strength Interstitial-Free Steel Containing Phosphorus

Materials ◽  
2020 ◽  
Vol 13 (6) ◽  
pp. 1473
Author(s):  
Hao Wang ◽  
Yanping Bao ◽  
Chengyi Duan ◽  
Lu Lu ◽  
Yan Liu ◽  
...  
Keyword(s):  
Solid Solution ◽  
Grain Size ◽  
Rare Earth ◽  
High Strength ◽  
Rolling Process ◽  
P Element ◽  
Second Phase ◽  
Strengthening Effect ◽  
Interstitial Free ◽  
If Steel

The influence of rare earth Ce on the deep stamping property of high-strength interstitial-free (IF) steel containing phosphorus was analyzed. After adding 120 kg ferrocerium alloy (Ce content is 10%) in the steel, the inclusion statistics and the two-dimensional morphology of the samples in the direction of 1/4 thickness of slab and each rolling process were observed and compared by scanning electron microscope (SEM). After the samples in each rolling process were treated by acid leaching, the three-dimensional morphology and components of the second phase precipitates were observed by SEM and energy dispersive spectrometer (EDS). The microstructure of the sample was observed by optical microscope, and the grain size was compared. Meanwhile, the content and strength of the favorable texture were analyzed by X-ray diffraction (XRD). Finally, the mechanical properties of the product were analyzed. The results showed that: (1) The combination of rare earth Ce with activity O and S in steel had lower Gibbs free energy, and it was easy to generate CeAlO3, Ce2O2S, and Ce2O3. The inclusions size was obviously reduced, but the number of inclusions was increased after adding rare earth. The morphology of inclusions changed from chain and strip to spherical. The size of rare earth inclusions was mostly about 2–5 μm, distributed and dispersed, and their elastic modulus was close to that of steel matrix, which was conducive to improving the structure continuity of steel. (2) The rare earth compound had a high melting point. As a heterogeneous nucleation point, the nucleation rate was increased and the solidification structure was refined. The grade of grain size of products was increased by 1.5 grades, which is helpful to improve the strength and plasticity of metal. (3) Rare earth Ce can inhibit the segregation of P element at the grain boundary and the precipitation of Fe(Nb+Ti)P phase. It can effectively increase the solid solution amount of P element in steel, improve the solid solution strengthening effect of P element in high-strength IF steel, and obtain a large proportion of {111} favorable texture, which is conducive to improving the stamping formability index r90 value.

Sign in / Sign up

Export Citation Format

Share Document