Making silicon-carbide kiln furniture

1966 ◽  
Vol 23 (6) ◽  
pp. 328-329
Author(s):  
D. M. Strongin
Keyword(s):  
Silicon Carbide ◽  
Kiln Furniture

ADVANCER NITRIDE BONDED SILICON CARBIDE

Alloy Digest ◽  
1992 ◽  
Vol 41 (4) ◽  
Keyword(s):  
Silicon Carbide ◽  
Shear Strength ◽  
High Temperature ◽  
Physical Properties ◽  
Oxidation Resistance ◽  
High Temperature Strength ◽  
Kiln Furniture ◽  
Low Mass ◽  
Long Life

Abstract ADVANCER NITRIDE BONDED SILICON CARBIDE has exceptional high-temperature strength. Its oxidation resistance assures long life. It is a low-mass ceramic that is ideally suited to kiln furniture. This datasheet provides information on composition, physical properties, elasticity, and shear strength. Filing Code: Cer-11. Producer or source: Norton Company.

A Note on Silicon Carbide Kiln Furniture

1956 ◽  
Vol 15 (2) ◽  
pp. 127-138 ◽  
Author(s):  
R. S. Satyarthi ◽  
H. N. Roy
Keyword(s):  
Silicon Carbide ◽  
Kiln Furniture

Use of silicon ? carbide waste for making kiln furniture

1974 ◽  
Vol 31 (8) ◽  
pp. 555-558 ◽  
Author(s):  
K. A. Stukalina ◽  
R. G. Rozenberg ◽  
I. M. Berdichevskii
Keyword(s):  
Silicon Carbide ◽  
Kiln Furniture

Using silicon carbide for making kiln furniture

1979 ◽  
Vol 36 (2) ◽  
pp. 114-115 ◽  
Author(s):  
S. A. Polyakov ◽  
N. I. Sokolova ◽  
R. Yu. Abbasov ◽  
G. A. Tagiev
Keyword(s):  
Silicon Carbide ◽  
Kiln Furniture

Using recrystallized silicon carbide for refractory kiln furniture

1983 ◽  
Vol 40 (11) ◽  
pp. 560-561
Author(s):  
B. I. Polyak ◽  
A. S. Vlasov ◽  
T. V. Aleksandrova
Keyword(s):  
Silicon Carbide ◽  
Kiln Furniture

Irradiation behavior of pyrolytic silicon carbide

1983 ◽  
Vol 41 ◽  
pp. 72-73
Author(s):  
R. J. Lauf
Keyword(s):  
Silicon Carbide ◽  
Fission Products ◽  
Thermodynamics And Kinetics ◽  
Neutron Fluences ◽  
Fuel Particles ◽  
Sic Coatings ◽  
Irradiation Behavior ◽  
Kinetics Of ◽  
Htgr Fuel

Fuel particles for the High-Temperature Gas-Cooled Reactor (HTGR) contain a layer of pyrolytic silicon carbide to act as a miniature pressure vessel and primary fission product barrier. Optimization of the SiC with respect to fuel performance involves four areas of study: (a) characterization of as-deposited SiC coatings; (b) thermodynamics and kinetics of chemical reactions between SiC and fission products; (c) irradiation behavior of SiC in the absence of fission products; and (d) combined effects of irradiation and fission products. This paper reports the behavior of SiC deposited on inert microspheres and irradiated to fast neutron fluences typical of HTGR fuel at end-of-life.

Microstructural Evaluation of Silicon Carbide Whisker Reinforced Alumina Fabricated with Carbon-Coated Whiskers

1991 ◽  
Vol 49 ◽  
pp. 920-921
Author(s):  
K. B. Alexander ◽  
P. F. Becher
Keyword(s):  
Silicon Carbide ◽  
High Resolution Electron Microscopy ◽  
Ceramic Composites ◽  
Interface Debonding ◽  
Resolution Electron ◽  
Microstructural Evaluation ◽  
Carbon Coated ◽  
Electron Energy Loss ◽  
Interfacial Films ◽  
Debonding Process

The presence of interfacial films at the whisker-matrix interface can significantly influence the fracture toughness of ceramic composites. The film may alter the interface debonding process though changes in either the interfacial fracture energy or the residual stress at the interface. In addition, the films may affect the whisker pullout process through the frictional sliding coefficients or the extent of mechanical interlocking of the interface due to the whisker surface topography.Composites containing ACMC silicon carbide whiskers (SiCw) which had been coated with 5-10 nm of carbon and Tokai whiskers coated with 2 nm of carbon have been examined. High resolution electron microscopy (HREM) images of the interface were obtained with a JEOL 4000EX electron microscope. The whisker geometry used for HREM imaging is described in Reference 2. High spatial resolution (< 2-nm-diameter probe) parallel-collection electron energy loss spectroscopy (PEELS) measurements were obtained with a Philips EM400T/FEG microscope equipped with a Gatan Model 666 spectrometer.

TEM of grain growth and phase transformations during creep of SCS-6 silicon carbide fibers

1995 ◽  
Vol 53 ◽  
pp. 350-351
Author(s):  
L. A. Giannuzzi ◽  
C. A. Lewinsohn ◽  
C. E. Bakis ◽  
R. E. Tressler
Keyword(s):  
Silicon Carbide ◽  
Creep Rate ◽  
Vapor Deposition ◽  
Chemical Vapor ◽  
Primary Creep ◽  
Excess Carbon ◽  
Silicon Carbide Fibers ◽  
Sic Fiber ◽  
Carbon Core ◽  
Grain Width

The SCS-6 SiC fiber is a 142 μm diameter fiber consisting of four distinct regions of βSiC. These SiC regions vary in excess carbon content ranging from 10 a/o down to 5 a/o in the SiC1 through SiC3 region. The SiC4 region is stoichiometric. The SiC sub-grains in all regions grow radially outward from the carbon core of the fiber during the chemical vapor deposition processing of these fibers. In general, the sub-grain width changes from 50nm to 250nm while maintaining an aspect ratio of ~10:1 from the SiC1 through the SiC4 regions. In addition, the SiC shows a <110> texture, i.e., the {111} planes lie ±15° along the fiber axes. Previous has shown that the SCS-6 fiber (as well as the SCS-9 and the developmental SCS-50 μm fiber) undergoes primary creep (i.e., the creep rate constantly decreases as a function of time) throughout the lifetime of the creep test.

Sign in / Sign up

Export Citation Format

Share Document