Properties of carburized steel 18Kh2N4VA after overheating

1970 ◽  
Vol 12 (10) ◽  
pp. 818-822
Author(s):  
V. S. Sagaradze
Keyword(s):  
Carburized Steel ◽  
Steel 18Kh2n4va

scholarly journals Microstructure, Hardness, and Tensile Properties of Vacuum Carburizing Gear Steel

Metals ◽  
2021 ◽  
Vol 11 (2) ◽  
pp. 300
Author(s):  
Wu Chen ◽  
Xiaofei He ◽  
Wenchao Yu ◽  
Maoqiu Wang ◽  
Kefu Yao
Keyword(s):  
Tensile Properties ◽  
Tensile Tests ◽  
Case Depth ◽  
Strain Hardening Exponent ◽  
Austenitizing Temperature ◽  
Vacuum Carburizing ◽  
Experimental Steel ◽  
Strain Behavior ◽  
Carburized Steel ◽  
Vacuum Carburization

We investigated the effects of the austenitizing temperature on the microstructure, hardness, and tensile properties of case-carburized steel after vacuum carburization at 930 °C and then re-austenitization at 820–900 °C followed by oil quenching and tempering. The results show that fractures occurred early with the increase in the austenitizing temperature, although all the carburized specimens showed a similar case hardness of 800 HV0.2 and case depth of 1.2 mm. The highest fracture stress of 1919 MPa was obtained for the experimental steel when the austenitizing temperature was 840 °C due to its fine microstructure and relatively high percentage of retained austenite transformed into martensite during the tensile tests. We also found that the stress–strain behavior of case-carburized specimens could be described by the area-weighted curves of the carburized case and the core in combination. The strain hardening exponent was about 0.4 and did not vary with the increase in the austenitizing temperature. We concluded that the optimum austenitizing temperature was around 840 °C for the experimental steel.

Impact of Isotropic Superfinishing on Contact and Bending Fatigue of Carburized Steel

2002 ◽  
Author(s):  
Lane Winkelmann ◽  
Mark Michaud ◽  
Gary Sroka ◽  
A. Alan Swiglo
Keyword(s):  
Bending Fatigue ◽  
Carburized Steel

Effect of Soaking Time on Paste Carburizing of Carburized Low Carbon Steel

2017 ◽  
Vol 740 ◽  
pp. 93-99
Author(s):  
Muhammad Hafizuddin Jumadin ◽  
Bulan Abdullah ◽  
Muhammad Hussain Ismail ◽  
Siti Khadijah Alias ◽  
Samsiah Ahmad
Keyword(s):  
Carbon Steel ◽  
Carbon Content ◽  
Low Carbon Steel ◽  
Case Depth ◽  
Carbon Steels ◽  
Low Carbon ◽  
Soaking Time ◽  
Low Carbon Steels ◽  
Carburized Steel ◽  
Carburizing Process

Increase of soaking time contributed to the effectiveness of case depth formation, hardness properties and carbon content of carburized steel. This paper investigates the effect of different soaking time (7-9 hours) using powder and paste compound to the carburized steel. Low carbon steels were carburized using powder and paste compound for 7, 8 and 9 hours at temperature 1000°C. The transformation of microstructure and formation carbon rich layer was observed under microscope. The microhardness profiles were analyzed to investigate the length of case depth produced after the carburizing process. The increment of carbon content was considered to find the correlation between types of carburizing compound with time. Results shows that the longer carburized steel was soaked, the higher potential in formation of carbon rich layer, case depth and carbon content, which led to better hardness properties for carburized low carbon steel. Longer soaking time, 9 hours has a higher dispersion of carbon up to 41%-51% compare to 8 hours and 7 hours. By using paste carburizing, it has more potential of carbon atom to merge the microstructure to transform into cementite (1.53 wt% C) compare to powder (0.97 wt% C), which increases the hardness of carburized steel (13% higher).

scholarly journals Effects of Case Depth and Notch Shape on the Rotating Bending Fatigue Properties of Carburized Steel

1980 ◽  
Vol 66 (3) ◽  
pp. 410-417 ◽  
Author(s):  
Tôru FURUKAWA ◽  
Shizuyo KONUMA ◽  
Hideyasu SAKANIWA ◽  
Tadashi KASUYA
Keyword(s):  
Case Depth ◽  
Fatigue Properties ◽  
Bending Fatigue ◽  
Carburized Steel ◽  
Rotating Bending Fatigue ◽  
Rotating Bending

INVESTIGATION OF THERMAL DIFFUSIVITY–MICROHARDNESS CORRELATION EXTENDED TO SURFACE-NITRURED STEEL USING BOUBAKER POLYNOMIALS EXPANSION

2008 ◽  
Vol 22 (29) ◽  
pp. 2893-2907 ◽  
Author(s):  
TAHER GHRIB ◽  
KAREM BOUBAKER ◽  
MAHMOUD BOUHAFS
Keyword(s):  
Thermal Diffusivity ◽  
Non Destructive Testing ◽  
Destructive Testing ◽  
Carburized Steel ◽  
Steel Material ◽  
Boubaker Polynomials ◽  
Surface Performance ◽  
Special Concern ◽  
Quenched Steel ◽  
Non Destructive

This study sums up the authors recent works1–6 on steel regarding non-destructive testing and evaluation achieved between 2000 and 2008. The main related items are the establishment of a polynomial correlation4 between the thermal diffusivity and the Vickers' hardness HV using the recently established Boubaker polynomial expansion. This correlation is undoubtedly an efficient guide to set an NDT protocol to investigate steel-strengthened surface performance. Special attention is given to carburized steel material,6 as the existence of any appropriated NDT photothermal technique is demonstrated2,5,6 to be unavoidably subjected to some restrictive conditions. The perspectives of the new features of this recent technique are discussed, with special concern with differently treated material like nitrured and nitrocarburized quenched steel.

Carburized steel-update on a mature composite

1990 ◽  
Vol 8 (1) ◽  
pp. 33-53 ◽  
Author(s):  
Douglas V. Doane
Keyword(s):  
Carburized Steel
Sign in / Sign up

Export Citation Format

Share Document