Wear resistance of high-manganese steels with different structures

1968 ◽  
Vol 10 (10) ◽  
pp. 824-826
Author(s):  
A. G. Shchulepnikova
Keyword(s):  
Wear Resistance ◽  
High Manganese ◽  
High Manganese Steels ◽  
Manganese Steels

Wear resistance of high manganese steels doped with titanium

1988 ◽  
Vol 30 (7) ◽  
pp. 494-495
Author(s):  
V. I. Malevannyi ◽  
B. P. Naval'nev ◽  
A. S. Yutishev
Keyword(s):  
Wear Resistance ◽  
High Manganese ◽  
High Manganese Steels ◽  
Manganese Steels

Influence of Heat Treatment on Wear Resistance of Alloyed Hadfield Steel and Phase Transformations in it

2017 ◽  
Vol 265 ◽  
pp. 640-645
Author(s):  
K.N. Vdovin ◽  
N.A. Feoktistov ◽  
D.A. Gorlenko
Keyword(s):  
Heat Treatment ◽  
Wear Resistance ◽  
Thermo Gravimetric Analysis ◽  
Research Work ◽  
Manganese Steel ◽  
Gravimetric Analysis ◽  
High Manganese ◽  
High Manganese Steel ◽  
High Manganese Steels ◽  
Manganese Steels

The paper investigates the influence of alloying of high manganese steel with various materials on its wear resistance. It describes the results of differential scanning calorimetry and thermo-gravimetric analysis obtained in the process of thermal investigation of high manganese steel alloyed with different materials. The processes taking place in alloyed high manganese steel during heat treatment were considered. Besides, the paper shows the results of investigation of kinetics of oxidation of high manganese steels, temperatures of the start and completion of carbide decomposition and carbon burning; the comparative analysis of these processes was carried out. The research group determined the qualitative characteristics of the steel decarburization process depending on the implemented alloying scheme of high manganese steel. Scientific justification was given to the results obtained in the research work. The technological recommendations, which make it possible to calculate the optimum hardening temperature of high manganese steels, were given. General conclusions were made in the final part of the paper.

Austenite Grain Growth in High Manganese Steels

2019 ◽  
Vol 50 (12) ◽  
pp. 5760-5766 ◽  
Author(s):  
Madhumanti Bhattacharyya ◽  
Yves Brechet ◽  
Gary R. Purdy ◽  
Hatem S. Zurob
Keyword(s):  
Grain Growth ◽  
High Manganese ◽  
Austenite Grain ◽  
High Manganese Steels ◽  
Austenite Grain Growth ◽  
Manganese Steels

scholarly journals Mechanical Properties and Microstructural Aspects of Two High-Manganese Steels with TWIP/TRIP Effects: A Comparative Study

Metals ◽  
2020 ◽  
Vol 11 (1) ◽  
pp. 24
Author(s):  
Matías Bordone ◽  
Juan Perez-Ipiña ◽  
Raúl Bolmaro ◽  
Alfredo Artigas ◽  
Alberto Monsalve
Keyword(s):  
Mechanical Response ◽  
Volume Fraction ◽  
Tensile Tests ◽  
Optical Microscope ◽  
Chemical Compositions ◽  
High Manganese ◽  
Microstructural Changes ◽  
Ε Martensite ◽  
High Manganese Steels ◽  
Manganese Steels

This article is focused on the mechanical behavior and its relationship with the microstructural changes observed in two high-manganese steels presenting twinning-induced plasticity (TWIP) and transformation-induced plasticity (TRIP), namely Steel B and Steel C, respectively. Chemical compositions were similar in manganese, but carbon content of Steel B approximately doubles Steel C, which directly impacted on the stacking fault energy (SFE), microstructure and mechanical response of each alloy. Characterization of as-cast condition by optical microscope revealed a fully austenitic microstructure in Steel B and a mixed microstructure in Steel C consisting of austenite grains and thermal-induced (εt) martensite platelets. Same phases were observed after the thermo-mechanical treatment and tensile tests, corroborated by means of X-Ray Diffraction (XRD), which confirms no phase transformation in Steel B and TRIP effect in Steel C, due to the strain-induced γFCC→εHCP transformation that results in an increase in the ε-martensite volume fraction. Higher values of ultimate tensile strength, yield stress, ductility and impact toughness were obtained for Steel B. Significant microstructural changes were revealed in tensile specimens as a consequence of the operating hardening mechanisms. Scanning Electron Microscopy (SEM) observations on the tensile and impact test specimens showed differences in fracture micro-mechanisms.

A new constitution diagram for dissimilar metal welds of high-manganese steels

2018 ◽  
Vol 63 (2) ◽  
pp. 491-499
Author(s):  
Benjamin Wittig ◽  
Manuela Zinke ◽  
Sven Jüttner ◽  
Daniel Keil
Keyword(s):  
Constitution Diagram ◽  
High Manganese ◽  
Dissimilar Metal ◽  
High Manganese Steels ◽  
Manganese Steels
Sign in / Sign up

Export Citation Format

Share Document