Relationship between intercrystalline corrosion of stainless steels and the thermodynamic characteristics of carbides

1973 ◽  
Vol 15 (12) ◽  
pp. 1021-1025
Author(s):  
S. D. Bogolyubskii ◽  
E. A. Ul'yanin
Keyword(s):  
Stainless Steels ◽  
Thermodynamic Characteristics ◽  
Intercrystalline Corrosion

The causes of intercrystalline corrosion in stainless steels

1972 ◽  
Vol 14 (7) ◽  
pp. 590-595
Author(s):  
A. P. Gulyaev ◽  
N. V. Andrushova ◽  
Yu. V. Zakharov
Keyword(s):  
Stainless Steels ◽  
Intercrystalline Corrosion

Intercrystalline corrosion of some stainless steels

1966 ◽  
Vol 7 (12) ◽  
pp. 776-780 ◽  
Author(s):  
A. P. Gulyaev ◽  
K. E. Miroshnikova
Keyword(s):  
Stainless Steels ◽  
Intercrystalline Corrosion

NiAl precipitation in Fe-12w/o Cr-5w/o Ni-4w/o Al

1983 ◽  
Vol 41 ◽  
pp. 202-203
Author(s):  
L.E. Murr ◽  
J.S. Dunning ◽  
S. Shankar
Keyword(s):  
Solid Solution ◽  
Stainless Steel ◽  
Stainless Steels ◽  
Alloy Composition ◽  
Chromium Content ◽  
Scale Up ◽  
Optical Metallography ◽  
Property Evaluation ◽  
310 Stainless Steel ◽  
Microstructural Studies

Aluminum additions to conventional 18Cr-8Ni austenitic stainless steel compositions impart excellent resistance to high sulfur environments. However, problems are typically encountered with aluminum additions above about 1% due to embrittlement caused by aluminum in solid solution and the precipitation of NiAl. Consequently, little use has been made of aluminum alloy additions to stainless steels for use in sulfur or H2S environments in the chemical industry, energy conversion or generation, and mineral processing, for example.A research program at the Albany Research Center has concentrated on the development of a wrought alloy composition with as low a chromium content as possible, with the idea of developing a low-chromium substitute for 310 stainless steel (25Cr-20Ni) which is often used in high-sulfur environments. On the basis of workability and microstructural studies involving optical metallography on 100g button ingots soaked at 700°C and air-cooled, a low-alloy composition Fe-12Cr-5Ni-4Al (in wt %) was selected for scale up and property evaluation.

Radiation Damage Studies with the HVEM

1972 ◽  
Vol 30 ◽  
pp. 680-681
Author(s):  
J. J. Laidler ◽  
B. Mastel
Keyword(s):  
Radiation Damage ◽  
Stainless Steels ◽  
Volume Expansion ◽  
Austenitic Stainless Steels ◽  
Test Facility ◽  
Fast Breeder Reactors ◽  
Breeder Reactors ◽  
Under Construction ◽  
Development Laboratory ◽  
Insight Into

One of the major materials problems encountered in the development of fast breeder reactors for commercial power generation is the phenomenon of swelling in core structural components and fuel cladding. This volume expansion, which is due to the retention of lattice vacancies by agglomeration into large polyhedral clusters (voids), may amount to ten percent or greater at goal fluences in some austenitic stainless steels. From a design standpoint, this is an undesirable situation, and it is necessary to obtain experimental confirmation that such excessive volume expansion will not occur in materials selected for core applications in the Fast Flux Test Facility, the prototypic LMFBR now under construction at the Hanford Engineering Development Laboratory (HEDL). The HEDL JEM-1000 1 MeV electron microscope is being used to provide an insight into trends of radiation damage accumulation in stainless steels, since it is possible to produce atom displacements at an accelerated rate with 1 MeV electrons, while the specimen is under continuous observation.

Strain-induced martensite effects on transgranular carbide precipitation in type 304 stainless steels

1991 ◽  
Vol 49 ◽  
pp. 604-605
Author(s):  
A.H. Advani ◽  
L.E. Murr ◽  
D. Matlock
Keyword(s):  
Heat Treatment ◽  
Grain Boundary ◽  
Stress Corrosion Cracking ◽  
Stainless Steels ◽  
Deformation Twin ◽  
Austenitic Stainless Steels ◽  
Carbide Precipitation ◽  
Strain Induced Martensite ◽  
Type 304

Thermomechanically induced strain is a key variable producing accelerated carbide precipitation, sensitization and stress corrosion cracking in austenitic stainless steels (SS). Recent work has indicated that higher levels of strain (above 20%) also produce transgranular (TG) carbide precipitation and corrosion simultaneous with the grain boundary phenomenon in 316 SS. Transgranular precipitates were noted to form primarily on deformation twin-fault planes and their intersections in 316 SS.Briant has indicated that TG precipitation in 316 SS is significantly different from 304 SS due to the formation of strain-induced martensite on 304 SS, though an understanding of the role of martensite on the process has not been developed. This study is concerned with evaluating the effects of strain and strain-induced martensite on TG carbide precipitation in 304 SS. The study was performed on samples of a 0.051%C-304 SS deformed to 33% followed by heat treatment at 670°C for 1 h.

Sign in / Sign up

Export Citation Format

Share Document