Damage accumulation in filled organosilicon rubber under pulsating loading

1988 ◽  
Vol 24 (1) ◽  
pp. 118-122 ◽  
Author(s):  
V. M. Parfeev ◽  
M. Ya. Tutan ◽  
U. �. Krauya ◽  
A. A. Strukovskis
Keyword(s):  
Damage Accumulation ◽  
Organosilicon Rubber

Fatigue of Unidirectional Cord-Rubber Composites

1999 ◽  
Vol 27 (1) ◽  
pp. 48-57 ◽  
Author(s):  
Y. Liu ◽  
Z. Wan ◽  
Z. Tian ◽  
X. Du ◽  
J. Jiang ◽  
...  
Keyword(s):  
Damage Accumulation ◽  
Fatigue Testing ◽  
Fatigue Behavior ◽  
Constant Load ◽  
Testing System ◽  
Rubber Composites ◽  
Cycle Frequency ◽  
Periodic Loading ◽  
Fatigue Damage Accumulation ◽  
Rubber Composite

Abstract A fatigue testing system is established with which the real-time recording of stress, strain, temperature, and hysteresis loss of rubbers or cord-rubber composite specimens subjected to periodic loading or extension can be successfully carried out. Several problems are connected with the experimental study of the fatigue of rubber composites. In constant extension cycling, the specimen becomes relaxed because of the viscoelasticity of rubber composites, and the imposed tension-tension deformation becomes complex. In this method, the specimen is unlikely to fail unless the imposed extensions are very large. Constant load cycling can avoid the shortcomings of constant extension cycling. The specially designed clamps ensure that the specimen does not slip when the load retains a constant value. The Deformation and fatigue damage accumulation processes of rubber composites under periodic loading are also examined. Obviously, the effect of cycle frequency on the fatigue life of rubber composites can not be ignored because of the viscoelasticity of constituent materials. The increase of specimen surface temperature is relatively small in the case of 1 Hz, but the temperature can easily reach 100°C at the 8 Hz frequency. A method for evaluating the fatigue behavior of tires is proposed.

Damage accumulation near a hole under low cycle fatigue proceeding from measurements of local deformation response

2020 ◽  
Vol 86 (10) ◽  
pp. 46-55
Author(s):  
S. I. Eleonsky ◽  
Yu. G. Matvienko ◽  
V. S. Pisarev ◽  
A. V. Chernov
Keyword(s):  
Stress Intensity Factor ◽  
Stress Intensity ◽  
Intensity Factor ◽  
Damage Accumulation ◽  
Stress Ratio ◽  
Low Cycle Fatigue ◽  
Accumulation Process ◽  
Stress Range ◽  
Cycle Fatigue ◽  
Deformation Response

A new destructive method for quantitative determination of the damage accumulation in the vicinity of a stress concentrator has been proposed and verified. Increase of damage degree in local area with a high level of the strain gradient was achieved through preliminary low-cycle pull-push loading of plane specimens with central open holes. The above procedure is performed for three programs at the same stress range (333.3 MPa) and different stress ratio values 0.33, – 0.66 and – 1.0, and vice versa for two programs at the same stress ratio – 0.33 and different stress range 333.3 and 233.3 MPa. This process offers a set of the objects to be considered with different degree of accumulated fatigue damages. The key point of the developed approach consists in the fact that plane specimens with open holes are tested under real operation conditions without a preliminary notching of the specimen initiating the fatigue crack growth. The measured parameters necessary for a quantitative description of the damage accumulation process were obtained by removing the local volume of the material in the form of a sequence of narrow notches at a constant level of external tensile stress. External load can be considered an amplifier enhancing a useful signal responsible for revealing the material damage. The notch is intended for assessing the level of fatigue damage, just as probe holes are used to release residual stress energy in the hole drilling method. Measurements of the deformation response caused by local removing of the material are carried out by electronic speckle-pattern interferometry at different stages of low-cycle fatigue. The transition from measured in-plane displacements to the values of the stress intensity factor (SIF) and the T-stress was carried out on the basis of the relations of linear fracture mechanics. It was shown that the normalized dependences of the stress intensity factor on the durability percentage for the first notch (constructed for four programs of cyclic loading with different parameters), reflect the effect of the stress ratio and stress range of the loading cycle on the rate of damage accumulation. The data were used to obtain the explicit form of the damage accumulation function that quantitatively describes damage accumulation process. The functions were constructed for different stress ratios and stress ranges.

Fatigue damage accumulation around notches

2004 ◽  
Vol 46 (6) ◽  
pp. 309-313
Author(s):  
Yutaka Iino ◽  
Hideo Yano
Keyword(s):  
Fatigue Damage ◽  
Damage Accumulation ◽  
Fatigue Damage Accumulation

A NEW SIMPLE DAMAGE ACCUMULATION MODEL FOR PREDICTING OF AN ASPHALT CONCRETE CYCLIC STRENGTH

2018 ◽  
Vol 431 (5) ◽  
pp. 38-47
Author(s):  
A. I. Iskakbayev ◽  
◽  
Bagdat Teltayev ◽  
Rossi C. Oliviero ◽  
K. Estayev ◽  
...  
Keyword(s):  
Asphalt Concrete ◽  
Damage Accumulation ◽  
Cyclic Strength ◽  
Accumulation Model ◽  
Damage Accumulation Model

Acoustic emission and X-ray computed microtomography characterization of damage accumulation in a woven Cf/SiC composite

2019 ◽  
Vol 155 ◽  
pp. 109748
Author(s):  
Yudong Xue ◽  
Qinglei Wang ◽  
Jianbao Hu ◽  
Haijun Zhou ◽  
Qingliang Shan ◽  
...  
Keyword(s):  
Acoustic Emission ◽  
Damage Accumulation ◽  
X Ray ◽  
Computed Microtomography ◽  
X Ray Computed
Sign in / Sign up

Export Citation Format

Share Document