High temperature mechanical behaviour of an uncoated SiC-SiC composite material

1991 ◽  
Vol 26 (7) ◽  
pp. 1891-1898 ◽  
Author(s):  
M. Gomina ◽  
P. Fourvel ◽  
M. -H. Rouillon
Keyword(s):  
Composite Material ◽  
High Temperature ◽  
Mechanical Behaviour

scholarly journals Effects of Double-Ageing Heat Treatments on the Microstructure and Mechanical Behaviour of a Ti-3.5Al-5Mo-4V Alloy

Materials ◽  
2021 ◽  
Vol 14 (1) ◽  
pp. 209
Author(s):  
Xuanming Ji ◽  
Panpan Ge ◽  
Song Xiang ◽  
Yuanbiao Tan
Keyword(s):  
Electron Microscopy ◽  
High Temperature ◽  
Low Temperature ◽  
Mechanical Behaviour ◽  
Ageing Time ◽  
Two Stage ◽  
Ageing Treatment ◽  
Ω Phase ◽  
Α Phase ◽  
Temperature Ageing

In this work, the effect of double-ageing heat treatments on the microstructural evolution and mechanical behaviour of a metastable β-titanium Ti-3.5Al-5Mo-4V alloy is investigated by X-ray diffraction (XRD), scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The double-ageing treatments are composed of low-temperature pre-ageing and high-temperature ageing, where the low-temperature pre-ageing is conducted at 300 °C or 350 °C for different times, and the high-temperature ageing is conducted at 500 °C for 8 h. The results show that the phase transformation sequence is altered with the time spent during the first ageing stage, the isothermal ω phase is precipitated in the pre-ageing process of the alloy at 300 °C and 350 °C with the change in the ageing time, and the ω phase is finally transformed into the α phase with the extension of pre-ageing time. The existence time of the ω phase is shortened as the pre-ageing temperature increases. The microhardness of the alloy increases with increasing pre-ageing time and temperature. Compared with single-stage ageing, the ω phase formed in the pre-ageing stage changes the response to subsequent high-temperature ageing. After the two-stage ageing treatment, the precipitation size of the α phase is obviously refined after the double-ageing treatment. A microhardness test shows that the microhardness of the two-stage aged alloy increases with extended pre-ageing time.

scholarly journals Mechanical behaviour at high temperature of alkali-activated aluminosilicates (geopolymers)

2015 ◽  
Vol 93 ◽  
pp. 1188-1196 ◽  
Author(s):  
Antonia Martin ◽  
Jose Y. Pastor ◽  
Angel Palomo ◽  
Ana Fernández Jiménez
Keyword(s):  
High Temperature ◽  
Mechanical Behaviour ◽  
Alkali Activated

Effect of Expanded Temperature on Microstructure of Carbon Nanotubes/Expanded Graphite Composites

2013 ◽  
Vol 716 ◽  
pp. 373-378
Author(s):  
Qian Zhang ◽  
Xin Bao Gao ◽  
Tian Peng Li
Keyword(s):  
Carbon Nanotubes ◽  
Composite Material ◽  
High Temperature ◽  
Carbon Nanotube ◽  
Physical Adsorption ◽  
Expanded Graphite ◽  
Graphite Flake ◽  
Graphite Composite ◽  
Multi Walled Carbon Nanotubes ◽  
Walled Carbon Nanotubes

Carbon nanotube/expanded graphite composite material was prepared by expanding the mixture of multi-walled carbon nanotubes and expansible graphite under the condition of high temperature. The microstructure and composition was studied by using SEM and XRD. The study shows that the tubular structure of carbon nanotubes in the composite material is changed by high temperature expanding process, and the microstructure is different with different expanding temperature. When the expanding temperature was 900°C, carbon nanotubes transformed, then attached to the surface of expanded graphite flake, so carbon nanotubes and expanding graphite combined strongly; globular carbon nanotubes attached to the surface of expanded graphite flake at the temperature of 700°C, both were combined much more strongly; carbon nanotubes retained the tube structure at the temperature of 500°C, combination was looser due to the simple physical adsorption. The result shows that the choice of expanding temperature has an important effect on microstructure of carbon nanotube/expanded graphite composite material.

Comparison of High Temperature Mechanical Behaviour and Microstructure of the New Gamma–TiAl8Ta with Gamma-TiAl8Nb Alloy

2010 ◽  
Vol 72 ◽  
pp. 40-45
Author(s):  
Giuliano Angella ◽  
Valentino Lupinc ◽  
Maurizio Maldini ◽  
Giovanni Onofrio
Keyword(s):  
High Temperature ◽  
Mechanical Behaviour ◽  
Low Cycle Fatigue ◽  
Fatigue Properties ◽  
Stress Intensity Factor Range ◽  
Fatigue Crack Propagation Rate ◽  
Difference Threshold ◽  
Temperature Range ◽  
R Ratio ◽  
Significant Difference

The high temperature creep and fatigue properties of two  -TiAl base intermetallic alloys, for gas turbine components, have been investigated within the Integrated European project IMPRESS. The alloys contain 8% at. of Ta or Nb, respectively. The microstructure of both alloys was cross convoluted lamellar rather than the well known conventional lamellar, typical of the usual -TiAl. The microstructure of the Ta containing alloy was homogeneous in all the analyzed batches whilst that of the Nb alloy appeared significantly spread out from specimen to specimen. The creep properties of the alloys were investigated in the temperature range 700-850°C with applied stresses in order to have times to rupture up to about 3,000 h. The creep behaviour presented no steady state regimes, but only minima of the creep rates between significant decelerating and accelerating regimes. The minimum creep rates of the Ta alloy resulted to be significantly slower than the Niobium alloy at the same creep conditions. In low cycle fatigue at 650 and 700°C the Ta  -TiAl showed longer lives than the Nb alloy, whilst the fatigue crack propagation rate in the same temperature range did not show any significant difference. Threshold values of stress intensity factor range were accurately measured at different R ratio. The microstructures of the two alloys were analysed by scanning microscopy in order to rationalise the different mechanical behaviour.

scholarly journals Europium monoxide as a basis for creating a high-temperature spin injector in the semiconductor spintronics

2020 ◽  
Vol 6 (3) ◽  
pp. 113-123
Author(s):  
Arnold S. Borukhovich
Keyword(s):  
Magnetic Field ◽  
Solid Solution ◽  
Composite Material ◽  
High Temperature ◽  
External Magnetic Field ◽  
Room Temperature ◽  
Spin Electronics ◽  
Wide Range ◽  
Semiconductor Spintronics ◽  
Europium Monoxide

The results of the creation of a high-temperature spin injector based on EuO: Fe composite material are discussed. Their magnetic, electrical, structural and resonance parameters are given in a wide range of temperatures and an external magnetic field. A model calculation of the electronic spectrum of the solid solution Eu–Fe–O, responsible for the manifestation of the outstanding properties of the composite, is performed. The possibility of creating semiconductor spin electronics devices capable of operating at room temperature is shown.

Sign in / Sign up

Export Citation Format

Share Document