Electron scanning microscopy of the antennal receptors in Tenebrio molitor

1974 ◽  
Vol 148 (1) ◽  
Author(s):  
R. Pierantoni
Keyword(s):  
Tenebrio Molitor ◽  
Scanning Microscopy ◽  
Electron Scanning Microscopy

scholarly journals Протонпроводящие композиционные материалы на основе соединения Cs-=SUB=-6-=/SUB=-H(HSO-=SUB=-4-=/SUB=-)-=SUB=-3-=/SUB=-(H-=SUB=-2-=/SUB=-PO-=SUB=-4-=/SUB=-)-=SUB=-4-=/SUB=-

2019 ◽  
Vol 61 (12) ◽  
pp. 2375
Author(s):  
В.А. Коморников ◽  
В.В. Гребенев ◽  
И.С. Тимаков ◽  
О.Б. Зайнуллин
Keyword(s):  
Impedance Spectroscopy ◽  
Transport Properties ◽  
Phase Analysis ◽  
Composition Range ◽  
Scanning Microscopy ◽  
Proton Conducting ◽  
X Ray ◽  
Conducting Materials ◽  
Electron Scanning Microscopy

Composite proton-conducting materials xCs6H (HSO4) 3 (H2PO4) 4+ (1 - x) AlPO4 were obtained in the composition range (x = 0.9–0.7). The methods of x-ray phase analysis, impedance spectroscopy, electron scanning microscopy studied their physicochemical and transport properties.

scholarly journals EFFECTS OF CHEMICAL PROCESSING AND OXIDE ETHYLENE STERILIZATION ON CORTICAL AND CANCELLOUS RAT BONE: A LIGHT AND ELECTRON SCANNING MICROSCOPY STUDY

2009 ◽  
Vol 44 (1) ◽  
pp. 32-39
Author(s):  
Marcello Teixeira Castiglia ◽  
Juliano Voltarelli F. da Silva ◽  
José Armendir Frezarim Thomazini ◽  
José Batista Volpon
Keyword(s):  
Microscopy Study ◽  
Scanning Microscopy ◽  
Chemical Processing ◽  
Electron Scanning Microscopy ◽  
Rat Bone

scholarly journals Multi-Scale Imaging of Tissues and Organoid Models by Backscattered Electron Scanning Microscopy after Pre- and Post-Embedding Immuno-Labeling

2019 ◽  
Vol 25 (S2) ◽  
pp. 1120-1121
Author(s):  
Mike Reichelt ◽  
Danielle Mandikian ◽  
Alejandro Lopez ◽  
Anand K. Katakam ◽  
Derek Smith ◽  
...  
Keyword(s):  
Scanning Microscopy ◽  
Multi Scale ◽  
Electron Scanning Microscopy ◽  
Backscattered Electron

Effect of the Dry Bulk Density on the Fired Properties of Clayey Ceramics

2012 ◽  
Vol 727-728 ◽  
pp. 988-992 ◽  
Author(s):  
V. Scarpini ◽  
R.M. Pinheiro ◽  
S.N. Monteiro ◽  
C.M.F. Vieira
Keyword(s):  
Compressive Strength ◽  
High Temperature ◽  
Water Absorption ◽  
Bulk Density ◽  
Strong Influence ◽  
Scanning Microscopy ◽  
Limited Attention ◽  
Laboratory Furnace ◽  
Electron Scanning Microscopy ◽  
Red Ceramics

Densification of a precursor mixture of powders followed by drying to remove the excess of water is a necessary stage before the high temperature sintering to produce a ceramic piece. In the case of conventional red ceramics the influence of the density established during this stage has received limited attention in terms of the final product proprieties. Therefore, this work has for objective to evaluate the influence of the dry bulk density on the fired properties of red ceramics elaborated with the mixture of clays, argillite and grog. Cylindrical specimens were prepared with two different ranges of dry bulk density, 1.95-2.09 g/cm3 and 2.15-2.28 g/cm3. Specimens were fired at 1050°C in a laboratory furnace. The evaluated properties were: water absorption, diametral shrinkage and compressive strength. Microstructure of the fired ceramics was evaluated by electron scanning microscopy. Results showed that dry bulk density exercises a strong influence on the fired properties.

scholarly journals Selected Properties And Tribological Wear Alloys Co-Cr-Mo And Co-Cr-Mo-W Used In Dental Prosthetics

2015 ◽  
Vol 60 (3) ◽  
pp. 1569-1574 ◽  
Author(s):  
J. Augustyn-Pieniążek ◽  
P. Kurtyka ◽  
I. Sulima ◽  
J. Stopka
Keyword(s):  
Wear Resistance ◽  
Abrasive Wear ◽  
High Hardness ◽  
Abrasive Wear Resistance ◽  
Scanning Microscopy ◽  
Electron Scanning Microscopy ◽  
Resistance Tests ◽  
Dental Prosthetics

Abstract The presented work provides the results of the abrasive wear resistance tests performed on Co-Cr-Mo and Co-Cr-Mo-W alloys with the use of the Miller’s apparatus. The analyzed alloys underwent microstructure observations as well as hardness measurements, and the abraded surfaces of the examined materials were observed by means of electron scanning microscopy. The performed examinations made it possible to state that the Co-Cr alloys characterized in a high hardness, whereas the changes in the mass decrement were minimal, which proved a high abrasive wear resistance.

Microhairs ofPlantago maritima L. under electron scanning microscopy

1998 ◽  
Vol 109 (3-4) ◽  
pp. 225-229
Author(s):  
E. Andrzejewska-Golec ◽  
J. Šwietoslawski
Keyword(s):  
Scanning Microscopy ◽  
Electron Scanning Microscopy
Sign in / Sign up

Export Citation Format

Share Document