scholarly journals Investigations on the stress intensity factor field for unstable dynamic crack growth

1992 ◽  
Vol 58 (4) ◽  
pp. 345-359 ◽  
Author(s):  
Chien-Ching Ma ◽  
Szu-Kuzi Chen
Keyword(s):  
Stress Intensity Factor ◽  
Stress Intensity ◽  
Intensity Factor ◽  
Crack Growth ◽  
Dynamic Crack ◽  
Dynamic Crack Growth

Crack Growth in Stainless Steel 304 under Creep-Fatigue Loading

2007 ◽  
Vol 353-358 ◽  
pp. 485-490 ◽  
Author(s):  
Y.M. Baik ◽  
K.S. Kim
Keyword(s):  
Stress Intensity Factor ◽  
Stainless Steel ◽  
Stress Intensity ◽  
Intensity Factor ◽  
Crack Growth ◽  
Growth Rates ◽  
Static Loading ◽  
Fatigue Loading ◽  
Creep Fatigue ◽  
Crack Growth Rates

Crack growth in compact specimens of type 304 stainless steel is studied at 538oC. Loading conditions include pure fatigue loading, static loading and fatigue loading with hold time. Crack growth rates are correlated with the stress intensity factor. A finite element analysis is performed to understand the crack tip field under creep-fatigue loading. It is found that fatigue loading interrupts stress relaxation around the crack tip and cause stress reinstatement, thereby accelerating crack growth compared with pure static loading. An effort is made to model crack growth rates under combined influence of creep and fatigue loading. The correlation with the stress intensity factor is found better when da/dt is used instead of da/dN. Both the linear summation rule and the dominant damage rule overestimate crack growth rates under creep-fatigue loading. A model is proposed to better correlate crack growth rates under creep-fatigue loading: 1 c f da da da dt dt dt Ψ −Ψ     =         , where Ψ is an exponent determined from damage under pure fatigue loading and pure creep loading. This model correlates crack growth rates for relatively small loads and low stress intensity factors. However, correlation becomes poor as the crack growth rate becomes large under a high level of load.

Slow Crack Growth in Glasses and Ceramics Under Residual and Applied Stresses

1989 ◽  
Vol 111 (1) ◽  
pp. 61-67 ◽  
Author(s):  
F. Erdogan
Keyword(s):  
Stress Intensity Factor ◽  
Stress Intensity ◽  
Intensity Factor ◽  
Residual Stresses ◽  
Crack Growth ◽  
Slow Crack Growth ◽  
Threshold Value ◽  
Crack Arrest ◽  
Growing Crack ◽  
Applied Stresses

The problem of slow crack growth under residual stresses and externally applied loads in plates is considered. Even though the technique developed to treat the problem is quite general, in the solution given it is assumed that the plate contains a surface crack and the residual stresses are compressive near and at the surfaces and tensile in the interior. The crack would start growing subcritically when the stress intensity factor exceeds a threshold value. Initially the crack faces near the plate surface would remain closed. A crack-contact problem would, therefore, have to be solved to calculate the stress intensity factor. Depending on the relative magnitudes of the residual and applied stresses and the threshold and critical stress intensity factors, the subcritically growing crack would either be arrested or become unstable. The problem is solved and examples showing the time to crack arrest or failure are discussed.

Effect of Temperature on Fatigue Crack Growth in CPVC

2003 ◽  
Vol 125 (1) ◽  
pp. 71-77 ◽  
Author(s):  
Muhammad Irfan-ul-Haq ◽  
Nesar Merah
Keyword(s):  
Stress Intensity Factor ◽  
Fatigue Crack ◽  
Stress Intensity ◽  
Fatigue Crack Growth ◽  
Intensity Factor ◽  
Crack Growth ◽  
Effect Of Temperature ◽  
Stress Intensity Factor Range ◽  
Crack Growth Behavior ◽  
Different Temperatures

This study addresses the effect of temperature on fatigue crack growth (FCG) behavior of CPVC. FCG tests were conducted on CPVC SEN tensile specimens in the temperature range −10 to 70°C. These specimens were prepared from 4-in. injection-molded pipe fittings. Crack growth behavior was studied using LEFM concepts. The stress intensity factor was modified to include the crack closure and plastic zone effects. The effective stress intensity factor range ΔKeff gave satisfactory correlation of crack growth rate (da/dN) at all temperatures of interest. The crack growth resistance was found to decrease with temperature increase. The effect of temperature on da/dN was investigated by considering the variation of mechanical properties with temperature. Master curves were developed by normalizing ΔKeff by fracture strain and yield stress. All the da/dN-ΔK curves at different temperatures were collapsed on a single curve. Crazing was found to be the dominant fatigue mechanism, especially at high temperature, while shear yielding was the dominant mechanism at low temperatures.

Mechanisms of Fatigue Crack Growth in WC-Co Cemented Carbides

2005 ◽  
Vol 297-300 ◽  
pp. 1120-1125 ◽  
Author(s):  
Myung Hwan Boo ◽  
Chi Yong Park
Keyword(s):  
Growth Rate ◽  
Stress Intensity Factor ◽  
Fatigue Crack ◽  
Stress Intensity ◽  
Fatigue Crack Growth ◽  
Intensity Factor ◽  
Crack Growth ◽  
Stress Ratio ◽  
Cemented Carbides ◽  
Stress Intensity Factor Range

In order to study the influence of stress ratio and WC grain size, the characteristics of fatigue crack growth were investigated in WC-Co cemented carbides with two different grain sizes of 3 and 6 µm. Fatigue crack growth tests were carried out over a wide range of fatigue crack growth rates covering the threshold stress intensity factor range DKth. It was found that crack growth rate da/dN against stress intensity factor range DK depended on stress ratio R. The crack growth rate plotted in terms of effective stress intensity factor range DKeff still exhibited the effect of microstructure. Fractographic examination revealed brittle fracture at R=0.1 and ductile fracture at R=0.5 in Co binder phase. The amount of Co phase transformation for stress ratio was closely related to fatigue crack growth characteristics.

Fatigue Damage Analysis on Crack Growth and Fatigue Life of Welded Bridge Members with Initial Crack

2006 ◽  
Vol 324-325 ◽  
pp. 251-254 ◽  
Author(s):  
Tai Quan Zhou ◽  
Tommy Hung Tin Chan ◽  
Yuan Hua
Keyword(s):  
Stress Intensity Factor ◽  
Fatigue Crack ◽  
Fatigue Life ◽  
Stress Intensity ◽  
Fatigue Crack Growth ◽  
Intensity Factor ◽  
Crack Growth ◽  
Fatigue Damage ◽  
Initial Crack ◽  
Traffic Loading

The behavior of crack growth with a view to fatigue damage accumulation on the tip of cracks is discussed. Fatigue life of welded components with initial crack in bridges under traffic loading is investigated. The study is presented in two parts. Firstly, a new model of fatigue crack growth for welded bridge member under traffic loading is presented. And the calculate method of the stress intensity factor necessary for evaluation of the fatigue life of welded bridge members with cracks is discussed. Based on the concept of continuum damage accumulated on the tip of fatigue cracks, the fatigue damage law suitable for steel bridge member under traffic loading is modified to consider the crack growth. The proposed fatigue crack growth can describe the relationship between the cracking count rate and the effective stress intensity factor. The proposed fatigue crack growth model is then applied to calculate the crack growth and the fatigue life of two types of welded components with fatigue experimental results. The stress intensity factors are modified by the factor of geometric shape for the welded components in order to reflect the influence of the welding type and geometry on the stress intensity factor. The calculated and measured fatigue lives are generally in good agreement, at some of the initial conditions of cracking, for a welded component widely used in steel bridges.

Time-Dependent Fracture of Polyimide Films

1993 ◽  
Vol 115 (3) ◽  
pp. 264-269 ◽  
Author(s):  
S. F. Popelar ◽  
C. H. Popelar ◽  
V. H. Kenner
Keyword(s):  
Stress Intensity Factor ◽  
Stress Intensity ◽  
Intensity Factor ◽  
Crack Growth ◽  
Practical Implication ◽  
Slow Crack Growth ◽  
Polymeric Materials ◽  
Polyimide Films ◽  
Test Protocol ◽  
Fracture Tests

A fracture mechanics approach for quantifying slow crack growth in thin polyimide films and assessing their structural integrity and life expectancy is presented. The methodology and techniques developed in this investigation may also be applied to other polymeric materials. A test protocol for studying slow crack growth is described. Room temperature fracture tests were performed and an analysis model was developed and validated to analyze the fracture tests. Correlations between the rate of crack growth and the crack driving force as measured by the stress intensity factor were made and contrasted for Kapton 100HN, 300H and 500HN polyimide films. The crack growth rate was found to depend very strongly upon the stress intensity factor. The practical implication of this finding is that the fracture of these polyimide films may be approximated as being controlled by a critical value of the stress intensity factor.

Sign in / Sign up

Export Citation Format

Share Document