Bismuth (Bi) compressibility, Young’s modulus, bulk modulus, Grüneisen parameters

2005 ◽  
pp. 1-3
Author(s):  
Keyword(s):  
Bulk Modulus ◽  
Young’S Modulus ◽  
Young's Modulus ◽  
Grüneisen Parameters ◽  
Gruneisen Parameters

Elastic constants of inflated lobes of dog lungs

1976 ◽  
Vol 40 (4) ◽  
pp. 508-513 ◽  
Author(s):  
S. J. Lai-Fook ◽  
T. A. Wilson ◽  
R. E. Hyatt ◽  
J. R. Rodarte
Keyword(s):  
Bulk Modulus ◽  
Young’S Modulus ◽  
Elastic Constants ◽  
Young's Modulus ◽  
Poisson Ratio ◽  
Inflation Pressure ◽  
Initial State ◽  
Volume Curve ◽  
Pressure Volume Curve ◽  
Indentation Tests

The elastic constants of dog lungs were determined at various degrees of inflation. In one set of experiments, the lobes were subjected to deformations that approximated the conditions of uniaxial loading. These data, together with the bulk modulus data obtained from the local slope of the pressure-volume curve, were used to determine the two elastic moduli that are needed to describe small nonuniform deformations about an initial state of uniform inflation. The bulk modulus was approximately 4 times the inflation pressure, and Young's modulus was approximately 1.5 times the inflation pressure. In a second set of experiments, lobes were subjected to indentation tests using cylindric punches 1–3 cm in diameter. The value for Young's modulus obtained from these data was slightly higher, approximately twice the inflation pressure. These experiments indicate that the lung is much more easily deformable in shear than in dilatation and that the Poisson ratio for the lung is high, approximately 0.43.

Differences between static and dynamic elastic moduli: Importance of experimental methods

2020 ◽  
Author(s):  
Elisabeth Bemer ◽  
Noalwenn Dubos-Sallée ◽  
Patrick N. J. Rasolofosaon
Keyword(s):  
Bulk Modulus ◽  
Young’S Modulus ◽  
Elastic Moduli ◽  
Young's Modulus ◽  
Local Strain ◽  
Experimental Methods ◽  
Triaxial Tests ◽  
Strain Gauges ◽  
Strain Measurements ◽  
Dynamic Elastic Moduli

<p>The differences between static and dynamic elastic moduli remain a controversial issue in rock physics. Various empirical correlations can be found in the literature. However, the experimental methods used to derive the static and dynamic elastic moduli differ and may entail substantial part of the discrepancies observed at the laboratory scale. The representativeness and bias of these methods should be fully assessed before applying big data analytics to the numerous datasets available in the literature.</p><p>We will illustrate, discuss and analyze the differences inherent to static and dynamic measurements through a series of triaxial and petroacoustic tests performed on an outcrop carbonate. The studied rock formation is Euville limestone, which is a crinoidal grainstone composed of roughly 99% calcite and coming from Meuse department located in Paris Basin. Sister plugs have been cored from the same quarry block and observed under CT-scanner to check their homogeneity levels.</p><p>The triaxial device is equipped with an internal stress sensor and provides axial strain measurements both from strain gauges glued to the samples and LVDTs placed inside the confinement chamber. Two measures of the static Young's modulus can thus be derived: the first one from the local strain measurements provided by the strain gauges and the second one from the semi-local strain measurements provided by the LVDTs. The P- and S-wave velocities are measured both through first break picking and the phase spectral ratio method, providing also two different measures of the dynamic Young's modulus.</p><p>The triaxial tests have been performed in drained conditions and the measured static elastic moduli correspond to drained elastic moduli. The petroacoustic tests have been performed using the fluid substitution method, which consists in measuring the acoustic velocities for various saturating fluids of different bulk modulus. No weakening or dispersion effects have been observed. Gassmann's equation can then be used to derive the dynamic drained elastic moduli and the solid matrix bulk modulus, which is otherwise either taken from the literature for pure calcite or dolomite samples, or computed using Voigt-Reuss-Hill or Hashin-Shtrikman averaging of the mineral constituents.</p><p>For the studied carbonate formation, we obtain similar values for static and dynamic elastic moduli when derived from careful lab experiments. Based on the obtained results, we will finally make recommendations, emphasizing the necessity of using relevant experimental techniques for a consistent characterization of the relation between static and dynamic elastic moduli.</p>

The Effect of Nitrogen Doping on the Elastic Properties of Silicene

2015 ◽  
Vol 245 ◽  
pp. 14-18
Author(s):  
Mary A. Chibisova ◽  
Andrey N. Chibisov
Keyword(s):  
Density Functional Theory ◽  
Bulk Modulus ◽  
Young’S Modulus ◽  
Elastic Properties ◽  
Density Functional ◽  
Nitrogen Doping ◽  
Young's Modulus ◽  
Functional Theory ◽  
Nitrogen Doped

This paper deals with the elastic properties of pure and nitrogen-doped silicene using density functional theory. During the compression (tension) from –2 to 2 GPa of pure and nitrogen-doped silicene, the corresponding values for the bulk modulus are obtained. It is found that the doping of the silicene structure with nitrogen has practically no effect on the value of its bulk modulus. However, the Young's modulus is increased of about 1.25 times.

Mechanical and thermodynamics properties of Al2Ca and Mg2Ca under various pressure: A first principle study

2021 ◽  
Vol 11 (9) ◽  
pp. 1571-1578
Author(s):  
Zai Gao Huang
Keyword(s):  
Shear Modulus ◽  
Bulk Modulus ◽  
Young’S Modulus ◽  
Elastic Constants ◽  
Coefficient Of Thermal Expansion ◽  
Young's Modulus ◽  
Structural Parameters ◽  
Harmonic Approximation ◽  
Polycrystalline Materials ◽  
Ductile Phase

The mechanical and thermodynamic properties of Al2Ca and Mg2Ca in the pressure range of 0~100 Gpa were investigated using first-principles calculations. The structural parameters, such as lattice constant ratio, unit cell volume ratio, density, were investigated. The calculated elastic constants satisfy the born’s stability criterion, indicating that they are mechanically stable at normal and high pressure. Mechanical parameters such as bulk modulus, shear modulus, and Young’s modulus of polycrystalline materials have been derived from single-crystal elastic constants. The Poisson’s ratio and anisotropy were investigated. The results show that the B/G value of Mg2Ca is greater than 1.75, indicating it is a ductile phase under various pressures. When the pressure was equal to 40 Gpa, Al2Ca was transferred brittle to toughness, and the bulk modulus, shear modulus, and Young’s modulus of Al2Ca were all larger than those of Mg2Ca, indicating that the comprehensive mechanical properties of Al2Ca are better than those of Mg2Ca. The constant heat capacity obtained by the quasi-harmonic approximation indicates that the ability of Mg2Ca to release or store heat is greater than that of Al2Ca. Moreover, the coefficient of thermal expansion (α) increases exponentially at lower temperatures and linearly at higher temperatures for both alloys.

scholarly journals Thermally Tunable Dynamic and Static Elastic Properties of Hydrogel Due to Volumetric Phase Transition

Polymers ◽  
2020 ◽  
Vol 12 (7) ◽  
pp. 1462 ◽  
Author(s):  
Yuqi Jin ◽  
Teng Yang ◽  
Shuai Ju ◽  
Haifeng Zhang ◽  
Tae-Youl Choi ◽  
...  
Keyword(s):  
Phase Transition ◽  
Bulk Modulus ◽  
Young’S Modulus ◽  
Elastic Properties ◽  
Poisson’S Ratio ◽  
Young's Modulus ◽  
Poisson's Ratio ◽  
Solution Temperature ◽  
Temperature Sensitive ◽  
Alginate Hydrogel

The temperature dependence of the mechanical properties of polyvinyl alcohol-based poly n-isopropyl acrylamide (PVA-PNIPAm) hydrogel was studied from the static and dynamic bulk modulus of the material. The effect of the temperature-induced volumetric phase transition on Young’s Modulus, Poisson’s ratio, and the density of PVA-PNIPAm was experimentally measured and compared with a non-thermo-responsive Alginate hydrogel as a reference. An increase in the temperature from 27.5 to 32 °C results in the conventional temperature-dependent de-swelling of the PVA-PNIPAm hydrogel volume of up to 70% at the lower critical solution temperature (LCST). However, with the increase in temperature, the PVA-PNIPAm hydrogel showed a drastic increase in Young’s Modulus and density of PVA-PNIPAm and a corresponding decrease in the Poisson’s ratio and the static bulk modulus around the LCST temperature. The dynamic bulk modulus of the PVA-PNIPAm hydrogel is highly frequency-dependent before the LCST and highly temperature-sensitive after the LCST. The dynamic elastic properties of the thermo-responsive PVA-PNIPAm hydrogel were compared and observed to be significantly different from the thermally insensitive Alginate hydrogel.

Lattice dynamical and elastic properties of BaFX (X = Cl, Br and I): Matlockite structure compounds

2019 ◽  
Vol 33 (20) ◽  
pp. 1950221 ◽  
Author(s):  
A. K. Kushwaha ◽  
S. Akbudak ◽  
A. C. Yadav ◽  
Ş. Uğur ◽  
G. Uğur
Keyword(s):  
Shear Modulus ◽  
Bulk Modulus ◽  
Young’S Modulus ◽  
Elastic Constants ◽  
Phonon Mode ◽  
Young's Modulus ◽  
Nearest Neighbors ◽  
Crystallographic Direction ◽  
Theoretical Results ◽  
Rigid Ion Model

In this study, an eleven-parameter rigid-ion model (RIM) is proposed for BaFX (X = Cl, Br and I) matlockite structure compounds. The interatomic interactions up to fourth nearest neighbors for the studied compounds are calculated. The zone-center raman and infrared phonon mode frequencies, elastic constants, bulk modulus B, shear modulus G, Young’s modulus E, Poisson’s coefficient, Debye temperature and sound velocity along [100], [110] and [001] directions have been calculated. It is observed that the studied BaFCl, BaFBr and BaFI compounds are stiffer in [100] direction than [001] crystallographic direction and the bulk modulus, shear modulus and Young’s modulus of the studied compounds decrease in the order of BaFCl [Formula: see text] BaFBr [Formula: see text] BaFI. The obtained results are compared with the theoretical and experimental results. It is observed that the obtained results agree very well with the experimental and theoretical results available in the literature.

Sign in / Sign up

Export Citation Format

Share Document