Investigating the vulnerability of nonductile reinforced concrete columns in moderate seismic regions to gravity load collapse

2018 ◽  
pp. e1578
Author(s):  
Tahir Mehmood ◽  
Kittipoon Rodsin ◽  
Pennung Warnitchai ◽  
Kristijan Kolozvari
Keyword(s):  
Reinforced Concrete ◽  
Concrete Columns ◽  
Reinforced Concrete Columns ◽  
Gravity Load ◽  
Seismic Regions ◽  
Moderate Seismic Regions

scholarly journals Gravity Load Collapse Behavior of Nonengineered Reinforced Concrete Columns

2018 ◽  
Vol 2018 ◽  
pp. 1-12 ◽  
Author(s):  
Chichaya Boonmee ◽  
Kittipoom Rodsin ◽  
Krissachai Sriboonma
Keyword(s):  
Reinforced Concrete ◽  
Cyclic Loading ◽  
Axial Load ◽  
Concrete Columns ◽  
Poor Quality ◽  
Load Level ◽  
Longitudinal Reinforcement ◽  
Reinforced Concrete Columns ◽  
Gravity Load ◽  
Collapse Behavior

This paper aims at investigating gravity load collapse behavior of extremely poor quality reinforced concrete columns under cyclic loading. Such columns were usually constructed by local people and may not be designed to meet any of the standards. It was found that their concrete strength may be as low as 5 MPa and the amount of longitudinal reinforcement may be lower than 1%. This type of column is deliberately defined as “nonengineered reinforced concrete column,” or NRCC. During earthquake, the gravity load collapse of the NRCC columns caused a large number of death tolls around the world. In this study, four columns as representative of existing NRCC were tested under cyclic loading. The compressive strength of concrete in order of 5 MPa was used to be representative of columns with poor quality concrete. Two axial load levels of 6 and 18 tons were used to study the influence of axial load level on maximum drift at gravity load collapse. To investigate the effect of bar types on drift capacity, 9 mm round bars were used in two specimens and 12 mm deformed bars were used for the rest of the specimens. The maximum drift before gravity load collapse was very dependent on the axial load level. The maximum drift of the specimens subjected to high axial load (18 tons) was extremely low at approximately 1.75% drifts. The use of deformed bars (associated with larger amount of longitudinal reinforcement) caused the damage to severely dissipate all over the height of the columns. Such damage caused columns to collapse at a lower drift compared to those using round bars. Finally, the plastic hinge model was used to predict the maximum drift of the low strength columns. It was found that the model overly underestimates the drift at gravity load collapse.

SETTING A DIAGRAM APPROACH TO CALCULATING VIBRATED, CENTRIFUGED AND VIBROCENTRIFUGED REINFORCED CONCRETE COLUMNS WITH A VARIATROPIC STRUCTURE

2020 ◽  
pp. 22-34
Author(s):  
Л. Р. Маилян ◽  
С. А. Стельмах ◽  
Е. М. Щербань ◽  
М. П. Нажуев
Keyword(s):  
Experimental Data ◽  
Reinforced Concrete ◽  
Bearing Capacity ◽  
Cross Section ◽  
Concrete Columns ◽  
Reinforced Concrete Columns ◽  
The Cross ◽  
Concrete Elements ◽  
Diagram Approach

Состояние проблемы. Железобетонные элементы изготавливаются, как правило, по трем основным технологиям - вибрированием, центрифугированием и виброцентрифугированием. Однако все основные расчетные зависимости для определения их несущей способности выведены, исходя из основного постулата - постоянства и равенства характеристик бетона по сечению, что реализуется лишь в вибрированных колоннах. Результаты. В рамках диаграммного подхода предложены итерационный, приближенный и упрощенный способы расчета несущей способности железобетонных вибрированных, центрифугированных и виброцентрифугированных колонн. Выводы. Расчет по диаграммному подходу показал существенно более подходящую сходимость с опытными данными, чем расчет по методике норм, а также дал лучшие результаты при использовании дифференциальных характеристик бетона, чем при использовании интегральных и, тем более, нормативных характеристик бетона. Statement of the problem. Reinforced concrete elements are typically manufactured according to three basic technologies - vibration, centrifugation and vibrocentrifugation. However, all the basic calculated dependencies for determining their bearing capacity were derived using the main postulate, i.e., the constancy and equality of the characteristics of concrete over the cross section, which is implemented only in vibrated columns. Results. Within the framework of the diagrammatic approach, iterative, approximate and simplified methods of calculating the bearing capacity of reinforced concrete vibrated, centrifuged and vibrocentrifuged columns are proposed. Conclusions. The calculation according to the diagrammatic approach showed a significantly better convergence with the experimental data than that using the method of norms, and also performs better when using differential characteristics of concrete than when employing integral and particularly standard characteristics of concrete.

Experimental Study on the Effect of Moisture Content on Hysteretic Behavior of Reinforced Concrete Columns

2018 ◽  
Vol 12 (1) ◽  
pp. 47-61
Author(s):  
Wenjuan Lv ◽  
Baodong Liu ◽  
Ming Li ◽  
Lin Li ◽  
Pengyuan Zhang
Keyword(s):  
Reinforced Concrete ◽  
Energy Dissipation ◽  
Moisture Content ◽  
Early Stage ◽  
Damping Ratio ◽  
Concrete Columns ◽  
Hysteretic Behavior ◽  
Cyclic Test ◽  
Experimental Result ◽  
Reinforced Concrete Columns

Background: For reinforced concrete structures under different humid conditions, the mechanical properties of concrete are significantly affected by the moisture content, which may result in a great change of the functional performance and bearing capacity. Objective: This paper presents an experiment to investigate the influence of the moisture content on the dynamic characteristics and hysteretic behavior of reinforced concrete column. Results: The results show that the natural frequency of reinforced concrete columns increases quickly at an early stage of immersion, but there is little change when the columns are close to saturation; the difference between the natural frequencies before and after cyclic test grows as the moisture content rises. The damping ratio slightly decreases first and then increases with the increase of moisture content; the damping ratio after the cyclic test is larger than before the test due to the development of the micro-cracks. Conclusion: The trend of energy dissipation is on the rise with increasing moisture content, although at an early stage, it decreases slightly. According to the experimental result, a formula for the moisture content on the average energy dissipation of reinforced concrete columns is proposed.

Sign in / Sign up

Export Citation Format

Share Document